Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

TPS7A4701RGWR

Low-Dropout (LDO) Voltage Regulator

The TPS7A4701RGWR is a low-dropout (ldo) voltage regulator from Texas Instruments. View the full TPS7A4701RGWR datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

TPS7A4701RGWR shares its datasheet with TPS7A4701, whose page lists every part number it covers.

Official TPS7A4701RGWR datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Package

VQFN-20

TPS7A4701RGWR Key Specifications

ParameterValue
Control FeaturesEnable
Output Current1A
Quiescent Current1 mA
Supply Current (Max)6.1 mA
Mounting TypeSurface Mount
Number of Regulators1
Operating Temperature-40°C ~ 125°C
Output ConfigurationPositive
Output TypeAdjustable
Package / Case20-VQFN Exposed Pad
Protection FeaturesOver Current, Over Temperature, Under Voltage Lockout (UVLO)
PSRR78dB (1kHz)
Supplier Device Package20-VQFN (5x5)
Input Voltage (Max)35V
Output Voltage (Max)34V
Output Voltage1.4V
Dropout Voltage0.45V @ 1A

TPS7A4701RGWR Overview

Part: TPS7A4701RGWT — Texas Instruments (TPS7A470x family)

Type: Positive High-Voltage Ultralow-Noise RF LDO Linear Regulator

Description: 3–35 V input, 1 A LDO with 4 μVRMS output noise (10 Hz–100 kHz), 307 mV typical dropout at 1 A, and an output range of 1.4–20.5 V (ANY-OUT) or up to 34 V (adjustable, TPS7A4701 only).

Operating Conditions:

  • Supply voltage (VI): 3.0–35.0 V
  • Operating temperature: -40 to 125 °C (junction)
  • Output voltage: 1.4–34.0 V; output current 0–1.0 A

Absolute Maximum Ratings:

  • Max voltage, IN / EN / OUT / NR / SENSE/FB / programming pins to GND: +36 V (min -0.4 V)
  • EN pin to IN pin: -36 V to +0.4 V
  • Peak output current: internally limited
  • Operating virtual junction temperature: -40 to 125 °C
  • Storage temperature: -65 to 150 °C

Key Specs:

  • Dropout voltage: 216 mV typ at 0.5 A; 307 mV typ, 450 mV max at 1 A (VI = 95% VO(nom))
  • Output accuracy: ±1.0% nominal (TJ = 25 °C); ±2.5% overall over line, load and temperature
  • Current limit: 1.26 A typ (1 A min), VO = 90% VO(nom)
  • Ground pin current: 0.58 mA typ (1.0 mA max) at IO = 0 mA; 6.1 mA typ at IO = 1 A
  • Shutdown current: 2.55 μA typ (8 μA max) at VEN = 0.4 V
  • PSRR: 78 dB typ at 1 kHz (VI = 16 V, VO = 15 V, IO = 500 mA, COUT = 50 μF, CNR = 1 μF)
  • Output noise: 4.17 μVRMS typ (VO = 1.4 V); 4.67 μVRMS typ (VO = 5 V); 10 Hz–100 kHz, CNR = 1 μF, COUT = 50 μF
  • UVLO: 2.67 V rising, 2.5 V falling; thermal shutdown 170 °C (reset at 150 °C)
  • Reference voltage: 1.4 V (TPS7A4701 adjustable mode); feedback pin current 350 nA typ

Features:

  • ANY-OUT user-programmable output via PCB layout, with no external feedback resistors or feed-forward capacitors
  • Adjustable output with external resistors (TPS7A4701 only)
  • Power-supply ripple rejection: 82 dB at 100 Hz; at least 55 dB from 10 Hz to 10 MHz
  • CMOS logic-compatible enable pin
  • Built-in fixed current limit and thermal shutdown
  • High-performance thermal package: 5 mm × 5 mm QFN

Applications:

  • Voltage-controlled oscillators and frequency synthesizers
  • Test and measurement, instrumentation, medical, audio
  • RX, TX and PA circuitry
  • Supply rails for op amps, DACs, ADCs and other precision analog circuitry
  • Post DC-DC converter regulation and ripple filtering
  • Base stations and telecom infrastructure
  • +12 V and +24 V industrial buses

Package:

  • VQFN-20 (RGW), 5 mm × 5 mm

TPS7A4701RGWR Features

  • Input Voltage Range: +3V to +36V
  • Output Voltage Noise: 4 μVRMS (10Hz, 100kHz)
  • Power-Supply Ripple Rejection:
  • -82dB (100Hz)
  • -≥ 55dB (10Hz, 10MHz)
  • Two Output Voltage Modes:
  • -ANY-OUT ™ Version (User-Programmable Output via PCB Layout):
  • No External Feedback Resistors or FeedForward Capacitors Required
  • Output Voltage Range: +1.4V to +20.5V
  • -Adjustable Version (TPS7A4701 only):
  • Output Voltage Range: +1.4V to +34V
  • Output Current: 1A
  • Dropout Voltage: 307mV at 1A
  • CMOS Logic Level-Compatible Enable Pin
  • Built-In Fixed Current Limit and Thermal Shutdown
  • Available in High-Performance Thermal Package: 5-mm × 5-mm QFN
  • Operating Temperature Range: -40°C to 125°C

TPS7A4701RGWR Applications

  • Voltage-Controlled Oscillators (VCO)
  • Frequency Synthesizers
  • Test and Measurement
  • Instrumentation, Medical, and Audio
  • RX, TX, and PA Circuitry
  • Supply Rails for Operational Amplifiers, DACs, ADCs, and Other High-Precision Analog Circuitry
  • Post DC-DC Converter Regulation and Ripple Filtering
  • Base Stations and Telecom Infrastructure
  • +12-V and +24-V Industrial Buses

TPS7A4701RGWR Pin Configuration

Figure 4-1. RGW Package 5-mm × 5-mm VQFN-20 (Top View)

Table 4-1. Pin Functions

PIN - NAMEPIN - NO.I/ODESCRIPTION
0P1V12IWhen connected to GND, this pin adds 0.1 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
0P2V11IWhen connected to GND, this pin adds 0.2 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
0P4V10IWhen connected to GND, this pin adds 0.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
0P8V9IWhen connected to GND, this pin adds 0.8 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
1P6V8IWhen connected to GND, this pin adds 1.6 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
3P2V6IWhen connected to GND, this pin adds 3.2 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
6P4V15IWhen connected to GND, this pin adds 6.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
6P4V24IWhen connected to GND, this pin adds 6.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating.
EN13IEnable pin. The device is enabled when the voltage on this pin exceeds the maximum enable voltage, V EN(HI) . If enable is not required, tie EN to IN.
GND7-Ground
IN15, 16IInput supply. A capacitor greater than or equal to 1 μF must be tied from this pin to ground to assure stability. A 10-μF capacitor is recommended to be connected from IN to GND (as close to the device as possible) to reduce circuit sensitivity to printed circuit board (PCB) layout, especially when long input traces or high source impedances are encountered.
NC2, 17-19-This pin can be left open or tied to any voltage between GND and IN.
NR14-Noise reduction pin. When a capacitor is connected from this pin to GND, RMS noise can be reduced to very low levels. A capacitor greater than or equal to 10 nF must be tied from this pin to ground to assure stability. A 1-μF capacitor is recommended to be connected from NR to GND (as close to the device as possible) to maximize ac performance and minimize noise.

TPS7A4701RGWR Electrical Characteristics

At -40°C ≤ TJ ≤ 125°C; VI = VO(nom) + 1.0 V or V I = 3.0 V (whichever is greater); V EN = VI ; IO = 0 mA; CIN =10 μF; COUT = 10 μF; CNR = 10 nF; SENSE/FB tied to OUT; and 0P1V, 0P2V, 0P4V, 0P8V, 1P6V, 3P2V, 6P4V1, 6P4V2 pins OPEN, unless otherwise noted.

PARAMETERTEST CONDITIONSMINTYPMAXUNIT
V IInput voltage range335V
VUnder-voltage lockout thresholdV I rising2.67V
UVLOV I falling2.5V
V (REF)Reference voltageV (REF) = V (FB) , TPS7A4701 only1.4V
V UVLO(HYS) V NRUnder-voltage lockout hysteresis Noise reduction pin voltageTPS7A4700, TPS7A4701 using ANY-OUT option177mV
V UVLO(HYS) V NRUnder-voltage lockout hysteresis Noise reduction pin voltageTPS7A4701 in adjustable modeonlyV OUT 1.4V V
V OOutput voltage rangeV I ≥ V O(nom) + 1.0 V or 3 V (whichever is greater), C OUT = 20 μFTPS7A4700, TPS7A4701 using ANY- OUT option1.420.5V
V OOutput voltage rangeV I ≥ V O(nom) + 1.0 V or 3 V (whichever is greater), C OUT = 20 μFTPS7A4701 using adjustable option1.434V
V ONominal accuracyT J = 25°C, C OUT = 20 μF-1.01.0%V O
V OOverall accuracyV O(nom) + 1.0 V ≤ V I ≤ 35 V, 0 mA ≤ I O ≤ 1 A, C OUT = 20 μF-2.52.5%V O
ΔV O(ΔVI)Line regulationV O(nom) + 1.0 V ≤ V I ≤ 35 V0.092%V O
ΔV O(ΔIO)Load regulation0 mA ≤ I O ≤ 1 A0.3%V O
V (DO)Dropout voltageV I = 95% V O(nom) , I O = 0.5 A216mV
V (DO)Dropout voltageV I = 95% V O(nom) , I O = 1 A307450mV
I (CL)Current limitV O = 90% V O(nom)11.26A
I (GND)Ground pin currentI O = 0 mA0.581.0mA
I (GND)Ground pin currentI O = 1 A6.1mA
I (EN)Enable pin currentV EN = V I0.782μA
I (EN)Enable pin currentV I = V EN = 35 V0.812μA
I (SHDN)Shutdown supply currentV EN = 0.4 V2.558μA
I (SHDN)Shutdown supply currentV EN = 0.4 V, V I = 35 V3.0460μA
V +EN(HI)Enable high-level voltage2.0V IV
V +EN(LO)Enable low-level voltage0.00.4V
I (FB)Feedback pin current350nA
PSRRPower-supply rejection ratioV I = 16 V, V O(nom) = 15 V, C OUT = 50 I O = 500 mA, C NR = 1 μF, f = 1 kHzμF,78dB
V nOutput noise voltageV I = 3 V, V O(nom) = 1.4 V, C OUT = 50 μF, C NR = 1 μF, BW = 10 Hz to 100 kHz4.17μV RMS
V nOutput noise voltageV IN = 6 V, V O(nom) = 5 V, C OUT = 50 μF, C NR = 1 μF, BW = 10 Hz to 100 kHz4.67μV RMS
T sdThermal shutdown temperatureShutdown, temperature increasing170°C
T sdThermal shutdown temperatureReset, temperature decreasing150°C
T JOperating junction temperature-40125°C

TPS7A4701RGWR Absolute Maximum Ratings

Over junction temperature range, unless otherwise noted. (1)

MINMAXUNIT
Voltage (2)IN pin to GND pin-0.4+36V
Voltage (2)EN pin to GND pin-0.4+36V
Voltage (2)EN pin to IN pin-36+0.4V
Voltage (2)OUT pin to GND pin-0.4+36V
Voltage (2)NR pin to GND pin-0.4+36V
Voltage (2)SENSE/FB pin to GND pin-0.4+36V
Voltage (2)0P1V pin to GND pin-0.4+36V
Voltage (2)0P2V pin to GND pin-0.4+36V
Voltage (2)0P4V pin to GND pin-0.4+36V
Voltage (2)0P8V pin to GND pin-0.4+36V
Voltage (2)1P6V pin to GND pin-0.4+36V
Voltage (2)3P2V pin to GND pin-0.4+36V
Voltage (2)6P4V1 pin to GND pin-0.4+36V
Voltage (2)6P4V2 pin to GND pin-0.4+36V
CurrentPeak outputInternally limitedInternally limitedInternally limited
TemperatureOperating virtual junction, T J-40125°C

over junction temperature range (unless otherwise noted)

MINNOMMAXUNIT
V I3.035.0V
V O1.434.0V
V EN0V INV
I O01.0A

TPS7A4701RGWR Thermal Information

THERMAL METRIC(1)TPS7A47xx RGW - 20 PINSUNIT
R θJAJunction-to-ambient thermal resistance32.5°C/W
R θJC(top)Junction-to-case (top) thermal resistance27°C/W
R θJBJunction-to-board thermal resistance11.9°C/W
ψ JTJunction-to-top characterization parameter0.3°C/W
ψ JBJunction-to-board characterization parameter11.9°C/W
R θJC(bot)Junction-to-case (bottom) thermal resistance1.7°C/W

TPS7A4701RGWR Typical Application

The TPS7A740x is a high-voltage, low-noise, 1-A LDO. Low-noise performance makes this LDO ideal for providing rail voltages to noise-sensitive loads, such as PLLs, oscillators, and high-speed ADCs.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
TPS7A4700Texas InstrumentsVQFN-20 5x5mm
TPS7A4701Texas InstrumentsVQFN-20 5x5mm
TPS7A4701RGWTTexas InstrumentsVQFN-20-EP(5x5)

Other Integrated Circuits

All Integrated Circuits datasheetsAll Texas Instruments datasheets (2,418)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TPS7A4701RGWR

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TPS7A4701RGWR run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.