TPS7A4701
Low-Dropout (LDO) Voltage RegulatorThe TPS7A4701 is a low-dropout (ldo) voltage regulator from Texas Instruments. View the full TPS7A4701 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
Official TPS7A4701 datasheet (PDF) — the source this page was extracted from.
TPS7A4701 Key Specifications
| Parameter | Value |
|---|---|
| Control Features | Enable |
| Output Current | 1A |
| Quiescent Current | 1 mA |
| Supply Current (Max) | 6.1 mA |
| Mounting Type | Surface Mount |
| Number of Regulators | 1 |
| Operating Temperature | -40°C ~ 125°C |
| Output Configuration | Positive |
| Output Type | Adjustable |
| Package / Case | 20-VQFN Exposed Pad |
| Protection Features | Over Current, Over Temperature, Under Voltage Lockout (UVLO) |
| PSRR | 78dB (1kHz) |
| Supplier Device Package | 20-VQFN (5x5) |
| Input Voltage (Max) | 35V |
| Output Voltage (Max) | 34V |
| Output Voltage | 1.4V |
| Dropout Voltage | 0.45V @ 1A |
TPS7A4701 Overview
Part: TPS7A4701RGWT — Texas Instruments (TPS7A470x family)
Type: Positive High-Voltage Ultralow-Noise RF LDO Linear Regulator
Description: 3–35 V input, 1 A LDO with 4 μVRMS output noise (10 Hz–100 kHz), 307 mV typical dropout at 1 A, and an output range of 1.4–20.5 V (ANY-OUT) or up to 34 V (adjustable, TPS7A4701 only).
Operating Conditions:
- Supply voltage (VI): 3.0–35.0 V
- Operating temperature: -40 to 125 °C (junction)
- Output voltage: 1.4–34.0 V; output current 0–1.0 A
Absolute Maximum Ratings:
- Max voltage, IN / EN / OUT / NR / SENSE/FB / programming pins to GND: +36 V (min -0.4 V)
- EN pin to IN pin: -36 V to +0.4 V
- Peak output current: internally limited
- Operating virtual junction temperature: -40 to 125 °C
- Storage temperature: -65 to 150 °C
Key Specs:
- Dropout voltage: 216 mV typ at 0.5 A; 307 mV typ, 450 mV max at 1 A (VI = 95% VO(nom))
- Output accuracy: ±1.0% nominal (TJ = 25 °C); ±2.5% overall over line, load and temperature
- Current limit: 1.26 A typ (1 A min), VO = 90% VO(nom)
- Ground pin current: 0.58 mA typ (1.0 mA max) at IO = 0 mA; 6.1 mA typ at IO = 1 A
- Shutdown current: 2.55 μA typ (8 μA max) at VEN = 0.4 V
- PSRR: 78 dB typ at 1 kHz (VI = 16 V, VO = 15 V, IO = 500 mA, COUT = 50 μF, CNR = 1 μF)
- Output noise: 4.17 μVRMS typ (VO = 1.4 V); 4.67 μVRMS typ (VO = 5 V); 10 Hz–100 kHz, CNR = 1 μF, COUT = 50 μF
- UVLO: 2.67 V rising, 2.5 V falling; thermal shutdown 170 °C (reset at 150 °C)
- Reference voltage: 1.4 V (TPS7A4701 adjustable mode); feedback pin current 350 nA typ
Features:
- ANY-OUT user-programmable output via PCB layout, with no external feedback resistors or feed-forward capacitors
- Adjustable output with external resistors (TPS7A4701 only)
- Power-supply ripple rejection: 82 dB at 100 Hz; at least 55 dB from 10 Hz to 10 MHz
- CMOS logic-compatible enable pin
- Built-in fixed current limit and thermal shutdown
- High-performance thermal package: 5 mm × 5 mm QFN
Applications:
- Voltage-controlled oscillators and frequency synthesizers
- Test and measurement, instrumentation, medical, audio
- RX, TX and PA circuitry
- Supply rails for op amps, DACs, ADCs and other precision analog circuitry
- Post DC-DC converter regulation and ripple filtering
- Base stations and telecom infrastructure
- +12 V and +24 V industrial buses
Package:
- VQFN-20 (RGW), 5 mm × 5 mm
TPS7A4701 Features
- Input Voltage Range: +3V to +36V
- Output Voltage Noise: 4 μVRMS (10Hz, 100kHz)
- Power-Supply Ripple Rejection:
- -82dB (100Hz)
- -≥ 55dB (10Hz, 10MHz)
- Two Output Voltage Modes:
- -ANY-OUT ™ Version (User-Programmable Output via PCB Layout):
- No External Feedback Resistors or FeedForward Capacitors Required
- Output Voltage Range: +1.4V to +20.5V
- -Adjustable Version (TPS7A4701 only):
- Output Voltage Range: +1.4V to +34V
- Output Current: 1A
- Dropout Voltage: 307mV at 1A
- CMOS Logic Level-Compatible Enable Pin
- Built-In Fixed Current Limit and Thermal Shutdown
- Available in High-Performance Thermal Package: 5-mm × 5-mm QFN
- Operating Temperature Range: -40°C to 125°C
TPS7A4701 Applications
- Voltage-Controlled Oscillators (VCO)
- Frequency Synthesizers
- Test and Measurement
- Instrumentation, Medical, and Audio
- RX, TX, and PA Circuitry
- Supply Rails for Operational Amplifiers, DACs, ADCs, and Other High-Precision Analog Circuitry
- Post DC-DC Converter Regulation and Ripple Filtering
- Base Stations and Telecom Infrastructure
- +12-V and +24-V Industrial Buses
TPS7A4701 Pin Configuration
Figure 4-1. RGW Package 5-mm × 5-mm VQFN-20 (Top View)
Table 4-1. Pin Functions
| PIN - NAME | PIN - NO. | I/O | DESCRIPTION |
|---|---|---|---|
| 0P1V | 12 | I | When connected to GND, this pin adds 0.1 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 0P2V | 11 | I | When connected to GND, this pin adds 0.2 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 0P4V | 10 | I | When connected to GND, this pin adds 0.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 0P8V | 9 | I | When connected to GND, this pin adds 0.8 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 1P6V | 8 | I | When connected to GND, this pin adds 1.6 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 3P2V | 6 | I | When connected to GND, this pin adds 3.2 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 6P4V1 | 5 | I | When connected to GND, this pin adds 6.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| 6P4V2 | 4 | I | When connected to GND, this pin adds 6.4 V to the nominal output voltage of the regulator. Do not connect any voltage other than GND to this pin. If not used, leave this pin floating. |
| EN | 13 | I | Enable pin. The device is enabled when the voltage on this pin exceeds the maximum enable voltage, V EN(HI) . If enable is not required, tie EN to IN. |
| GND | 7 | - | Ground |
| IN | 15, 16 | I | Input supply. A capacitor greater than or equal to 1 μF must be tied from this pin to ground to assure stability. A 10-μF capacitor is recommended to be connected from IN to GND (as close to the device as possible) to reduce circuit sensitivity to printed circuit board (PCB) layout, especially when long input traces or high source impedances are encountered. |
| NC | 2, 17-19 | - | This pin can be left open or tied to any voltage between GND and IN. |
| NR | 14 | - | Noise reduction pin. When a capacitor is connected from this pin to GND, RMS noise can be reduced to very low levels. A capacitor greater than or equal to 10 nF must be tied from this pin to ground to assure stability. A 1-μF capacitor is recommended to be connected from NR to GND (as close to the device as possible) to maximize ac performance and minimize noise. |
TPS7A4701 Electrical Characteristics
At -40°C ≤ TJ ≤ 125°C; VI = VO(nom) + 1.0 V or V I = 3.0 V (whichever is greater); V EN = VI ; IO = 0 mA; CIN =10 μF; COUT = 10 μF; CNR = 10 nF; SENSE/FB tied to OUT; and 0P1V, 0P2V, 0P4V, 0P8V, 1P6V, 3P2V, 6P4V1, 6P4V2 pins OPEN, unless otherwise noted.
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | ||
|---|---|---|---|---|---|---|---|
| V I | Input voltage range | 3 | 35 | V | |||
| V | Under-voltage lockout threshold | V I rising | 2.67 | V | |||
| UVLO | V I falling | 2.5 | V | ||||
| V (REF) | Reference voltage | V (REF) = V (FB) , TPS7A4701 only | 1.4 | V | |||
| V UVLO(HYS) V NR | Under-voltage lockout hysteresis Noise reduction pin voltage | TPS7A4700, TPS7A4701 using ANY-OUT option | 177 | mV | |||
| V UVLO(HYS) V NR | Under-voltage lockout hysteresis Noise reduction pin voltage | TPS7A4701 in adjustable mode | only | V OUT 1.4 | V V | ||
| V O | Output voltage range | V I ≥ V O(nom) + 1.0 V or 3 V (whichever is greater), C OUT = 20 μF | TPS7A4700, TPS7A4701 using ANY- OUT option | 1.4 | 20.5 | V | |
| V O | Output voltage range | V I ≥ V O(nom) + 1.0 V or 3 V (whichever is greater), C OUT = 20 μF | TPS7A4701 using adjustable option | 1.4 | 34 | V | |
| V O | Nominal accuracy | T J = 25°C, C OUT = 20 μF | -1.0 | 1.0 | %V O | ||
| V O | Overall accuracy | V O(nom) + 1.0 V ≤ V I ≤ 35 V, 0 mA ≤ I O ≤ 1 A, C OUT = 20 μF | -2.5 | 2.5 | %V O | ||
| ΔV O(ΔVI) | Line regulation | V O(nom) + 1.0 V ≤ V I ≤ 35 V | 0.092 | %V O | |||
| ΔV O(ΔIO) | Load regulation | 0 mA ≤ I O ≤ 1 A | 0.3 | %V O | |||
| V (DO) | Dropout voltage | V I = 95% V O(nom) , I O = 0.5 A | 216 | mV | |||
| V (DO) | Dropout voltage | V I = 95% V O(nom) , I O = 1 A | 307 | 450 | mV | ||
| I (CL) | Current limit | V O = 90% V O(nom) | 1 | 1.26 | A | ||
| I (GND) | Ground pin current | I O = 0 mA | 0.58 | 1.0 | mA | ||
| I (GND) | Ground pin current | I O = 1 A | 6.1 | mA | |||
| I (EN) | Enable pin current | V EN = V I | 0.78 | 2 | μA | ||
| I (EN) | Enable pin current | V I = V EN = 35 V | 0.81 | 2 | μA | ||
| I (SHDN) | Shutdown supply current | V EN = 0.4 V | 2.55 | 8 | μA | ||
| I (SHDN) | Shutdown supply current | V EN = 0.4 V, V I = 35 V | 3.04 | 60 | μA | ||
| V +EN(HI) | Enable high-level voltage | 2.0 | V I | V | |||
| V +EN(LO) | Enable low-level voltage | 0.0 | 0.4 | V | |||
| I (FB) | Feedback pin current | 350 | nA | ||||
| PSRR | Power-supply rejection ratio | V I = 16 V, V O(nom) = 15 V, C OUT = 50 I O = 500 mA, C NR = 1 μF, f = 1 kHz | μF, | 78 | dB | ||
| V n | Output noise voltage | V I = 3 V, V O(nom) = 1.4 V, C OUT = 50 μF, C NR = 1 μF, BW = 10 Hz to 100 kHz | 4.17 | μV RMS | |||
| V n | Output noise voltage | V IN = 6 V, V O(nom) = 5 V, C OUT = 50 μF, C NR = 1 μF, BW = 10 Hz to 100 kHz | 4.67 | μV RMS | |||
| T sd | Thermal shutdown temperature | Shutdown, temperature increasing | 170 | °C | |||
| T sd | Thermal shutdown temperature | Reset, temperature decreasing | 150 | °C | |||
| T J | Operating junction temperature | -40 | 125 | °C |
TPS7A4701 Absolute Maximum Ratings
Over junction temperature range, unless otherwise noted. (1)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| Voltage (2) | IN pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | EN pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | EN pin to IN pin | -36 | +0.4 | V |
| Voltage (2) | OUT pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | NR pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | SENSE/FB pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 0P1V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 0P2V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 0P4V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 0P8V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 1P6V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 3P2V pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 6P4V1 pin to GND pin | -0.4 | +36 | V |
| Voltage (2) | 6P4V2 pin to GND pin | -0.4 | +36 | V |
| Current | Peak output | Internally limited | Internally limited | Internally limited |
| Temperature | Operating virtual junction, T J | -40 | 125 | °C |
TPS7A4701 Recommended Operating Conditions
over junction temperature range (unless otherwise noted)
| MIN | NOM | MAX | UNIT | |
|---|---|---|---|---|
| V I | 3.0 | 35.0 | V | |
| V O | 1.4 | 34.0 | V | |
| V EN | 0 | V IN | V | |
| I O | 0 | 1.0 | A |
TPS7A4701 Thermal Information
| THERMAL METRIC | (1) | TPS7A47xx RGW - 20 PINS | UNIT |
|---|---|---|---|
| R θJA | Junction-to-ambient thermal resistance | 32.5 | °C/W |
| R θJC(top) | Junction-to-case (top) thermal resistance | 27 | °C/W |
| R θJB | Junction-to-board thermal resistance | 11.9 | °C/W |
| ψ JT | Junction-to-top characterization parameter | 0.3 | °C/W |
| ψ JB | Junction-to-board characterization parameter | 11.9 | °C/W |
| R θJC(bot) | Junction-to-case (bottom) thermal resistance | 1.7 | °C/W |
TPS7A4701 Typical Application
The TPS7A740x is a high-voltage, low-noise, 1-A LDO. Low-noise performance makes this LDO ideal for providing rail voltages to noise-sensitive loads, such as PLLs, oscillators, and high-speed ADCs.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| TPS7A4700 | Texas Instruments | VQFN-20 5x5mm |
| TPS7A4701RGWR | Texas Instruments | VQFN-20 5x5mm |
| TPS7A4701RGWT | Texas Instruments | VQFN-20-EP(5x5) |
Other Integrated Circuits
- STM32F103C8T6 – STMicroelectronics, Microcontroller
- STM32F405RGT6 – STMicroelectronics, ARM Cortex-M4 MCU
- SN74AVC4T245PWR – Texas Instruments, Dual-Supply Bus Transceiver Level Translator
- STM32F446RCT6 – STMicroelectronics, ARM Cortex-M4 MCU
- STM32G070RBT6 – STMicroelectronics, Arm Cortex-M0+ 32-bit MCU
- ADS131M08IPBSR – Texas Instruments, Delta-Sigma ADC
- ISO1540DR – Texas Instruments, Bidirectional I²C Isolator
- ISO7740DBQR – Texas Instruments, Digital Isolator
All Integrated Circuits datasheetsAll Texas Instruments datasheets (2,418)
Ask your AI agent about the TPS7A4701
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the TPS7A4701 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.