Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

TCAN330DR

CAN Transceiver

The TCAN330DR is a can transceiver from Texas Instruments. View the full TCAN330DR datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

TCAN330DR shares its datasheet with TCAN330, whose page lists every part number it covers.

Official TCAN330DR datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Package

SOIC-8

TCAN330DR Key Specifications

ParameterValue
Data Rate1Mbps
Mounting TypeSurface Mount
Number of Drivers/Receivers1/1
Operating Temperature-40°C ~ 125°C
Package / Case8-SOIC (0.154", 3.90mm Width)
PackagingTube
ProtocolCANbus
Standard Pack Qty75
Supplier Device Package8-SOIC
TypeTransceiver
Supply Voltage3V ~ 3.6V

TCAN330DR Overview

Part: TCAN330D (TCAN33x family) — Texas Instruments

Type: 3.3 V CAN Transceiver (CAN FD capable)

Description: 3.3 V single-supply, ISO 11898-2 compatible CAN transceiver with data rates up to 1 Mbps (up to 5 Mbps for TCAN33xG devices), ±12 V common-mode range, ±14 V bus fault protection and total loop delay under 135 ns.

Operating Conditions:

  • Supply voltage: 3–3.6 V
  • Operating temperature: -40 to 125 °C (free-air)
  • Common-mode range: ±12 V in normal and silent modes
  • Logic output current: -2 mA (high) to 2 mA (low)

Absolute Maximum Ratings:

  • Max supply voltage (VCC): 5 V
  • Bus terminal voltage (CANH, CANL): -14 to 14 V
  • Logic input/output voltage: -0.3 to 5 V
  • Logic output current: 8 mA
  • Max junction temperature: 150 °C
  • Storage temperature: up to 150 °C

Key Specs:

  • Supply current, dominant (TXD = 0 V, RL = 60 Ω): 55 mA max; 60 mA max at RL = 50 Ω
  • Supply current, recessive: 3.5 mA max; silent mode: 2.5 mA max
  • Standby current: 15 μA max (TA < 85 °C), 20 μA max over the full range
  • Shutdown current: 1 μA max (TA < 85 °C), 2.5 μA max over the full range
  • Differential output voltage, dominant: 1.6–3 V (50 Ω ≤ RL ≤ 65 Ω)
  • Receiver input threshold (normal mode): 500–900 mV, 120 mV typical hysteresis
  • Bus short-circuit dominant current: ±200 mA max
  • UVLO on VCC: rising 2.2 V typ / 2.6 V max; falling 2 V typ; 200 mV hysteresis
  • Thermal shutdown: 175 °C with 5 °C hysteresis
  • ESD: HBM ±25 kV on CANH/CANL, IEC 61000-4-2 contact ±12 kV

Features:

  • 3.3 V single supply; directly interfaces with 3.3 V CAN controllers/MCUs
  • Compatible with ISO 11898-2 and with 5 V CAN transceivers on the same bus
  • Operating modes: normal (all), standby with wake (TCAN334), silent (TCAN330, TCAN337), shutdown (TCAN330, TCAN334)
  • Driver and receiver dominant time-out (TXD DTO, RXD DTO)
  • Fault output pin (TCAN337 only)
  • Undervoltage protection on VCC, thermal shutdown, current limiting on bus pins
  • Bus and logic pins high impedance when unpowered; glitch-free power up/down
  • Excellent EMC performance

Applications:

  • 5 Mbps CAN FD networks (TCAN33xG devices)
  • 1 Mbps operation in highly loaded CAN networks
  • Industrial automation, control, sensors and drive systems
  • Building, security and climate control automation
  • Telecom base station status and control
  • CANopen, DeviceNet, NMEA2000, ARINC825, ISO11783, CANaerospace

Package:

  • SOIC-8 (D), 4.9 mm × 6 mm (TCAN330/G)
  • SOT-23-8 (DCN), 2.9 mm × 1.6 mm (TCAN332/G, TCAN334/G, TCAN337/G)

TCAN330DR Features

  • 3.3V Single supply operation
  • Data rates up to 5Mbps (TCAN33xG devices)
  • Compatible with ISO 11898-2
  • SOIC-8 and SOT-23 package options
  • Operating Modes:
  • -Normal mode (all devices)
  • -Low power standby mode with wake (TCAN334)
  • -Silent mode (TCAN330, TCAN337)
  • -Shutdown mode (TCAN330, TCAN334)
  • Wide common mode range of operation ±12V
  • Bus pin fault protection of ±14V
  • Total loop delay < 135ns
  • Wide ambient operation temperature range: -40°C to 125°C
  • Optimized behavior when unpowered:
  • -Bus and logic pins are high impedance (no load to operating bus or application)
  • -Power up / down glitch free operation
  • Excellent EMC performance
  • Protection features:
  • -ESD Protection of bus terminals
  • HBM ESD Protection exceeds ±25kV
  • IEC61000-4-2 ESD Contact discharge protection exceeds ±12kV
  • -Driver dominant time out (TXD DTO)
  • -Receiver dominant time out (RXD DTO)
  • -Fault output pin (TCAN337 only)
  • -Undervoltage protection on VCC
  • -Thermal shutdown protection
  • -Current limiting on bus pins

TCAN330DR Applications

TCAN330DR Pin Configuration

Figure 4-1. TCAN330 D, DCN Packages, 8-Pin SOIC, SOT-23, (Top View)

Figure 4-2. TCAN332 D, DCN Packages, 8-Pin SOIC, SOT-23, (Top View)

Figure 4-3. TCAN334 D, DCN Packages, 8-Pin SOIC, SOT-23, (Top View)

Figure 4-4. TCAN337 D, DCN Packages, 8-Pin SOIC, SOT-23, (Top View)

TCAN330DR Electrical Characteristics

over operating free-air temperature range, T J = -40°C to 150°C. All typical values are at 25°C and supply voltages of V CC = 3.3 V, R L = 60 Ω, (unless otherwise noted)

PARAMETERPARAMETERPARAMETERTEST CONDITIONSMINTYPMAXUNIT
Supply
I CCDominantSee Figure 6-1. TXD = 0V, R L = 60Ω, C L = open, S, STB and SHDN = 0V. Typical Bus Load.55mA
I CCSee Figure 6-1. TXD = 0V, R L = 50Ω, C L = open, S, STB and SHDN = 0V. High Bus Load.60mA
I CCDominant with bus faultSee Figure 6-1. TXD = 0V, S, STB and SHDN = 0V, CANH = -12V, R L = open, C L = open180mA
I CCRecessiveSee Figure 6-1. TXD = V CC , R L = 50Ω, C L = open, S, STB and SHDN = 0V3.5mA
I CCSupply Current: Silent ModeSupply Current: Silent ModeSee Figure 6-1. TXD = V CC , R L = 50Ω, C L = open, S = V CC2.5mA
I CCT A < 85°C, STB at V CC , RXD floating, TXD at V CC15μA
I CCSupply Current:Supply Current:STB at V CC , RXD floating, TXD at V CC20μA
I CCSupply Current:Supply Current:T A < 85°C, SHDN at V CC , RXD floating, TXD at V CC1μA
I CCSHDN = V CC , RXD floating, TXD at V CC2.5μA
UV (VCC)Rising under voltage detection on V CC for protected modeRising under voltage detection on V CC for protected mode2.22.6V
UV (VCC)Falling under voltage detection on V CC for protected modeFalling under voltage detection on V CC for protected mode1.6522.5V
V HYS(UVVCC)Hysteresis voltage on UV (VCC)Hysteresis voltage on UV (VCC)200mV
Driver
V O(D)CANHSee Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, R L = 60Ω, C L = open2.45V CCV
V O(D)CANLSee Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, R L = 60Ω, C L = open0.51.25V
V O(R)Bus output voltage (recessive)Bus output voltage (recessive)See Figure 6-3 and Figure 6-2, TXD = V CC , STB, SHDN = 0V, S = 0V or V CC (1) , R L = open (no load)1.851.851.85V

www.ti.com

TCAN330DR Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1) (2)

MINMAXUNIT
Supply Voltage range, V CC-0.35V
Voltage at any bus terminal (CANH or CANL), V (BUS)-1414V
Logic input terminal voltage range V (Logic_Input)-0.35V
Logic output terminal voltage range, V (Logic_Output)-0.35V
Logic output current, I O(LOGIC)8mA
Operating junction temperature range, T J-40150°C
Storage temperature, T stg150°C

over operating free-air temperature range (unless otherwise noted)

MINNOMMAXUNIT
V CCSupply voltage33.6V
I OH(LOGIC)Logic terminal HIGH level output current-2mA
I OL(LOGIC)Logic terminal LOW level output current2mA
T AOperational free-air temperature-40125°C

TCAN330DR Thermal Information

THERMAL METRICTCAN33x D (SOIC)TCAN33x DCN (SOT-23)UNIT
Junction-to-ambient thermal resistance114.4154.4°C/W
R θJA
R θJC(top)Junction-to-case (top) thermal resistance58.776.6°C/W
R θJBJunction-to-board thermal resistance55.249.2°C/W
ψ JTJunction-to-top characterization parameter11.711.9°C/W
ψ JBJunction-to-board characterization parameter54.649.2°C/W
R θJC(bot)Junction-to-case (bottom) thermal resistanceN/AN/A°C/W
P D TAverage power dissipation CC at 0 V, Input wave, C6565mW
SDThermal shutdown temperature175175°C
T HYSThermal shutdown hysteresis55°C

TCAN330DR Typical Application

Copyright © 2016, Texas Instruments Incorporated www.ti.com

Figure 7-1. Typical 3.3V Application

TCAN330DR Package Information

PART NUMBERPACKAGE (1)PACKAGE SIZE (2)
TCAN330/GSOIC (8)4.9mm × 6mm
TCAN332/G TCAN334/G TCAN337/GSOT-23 (8)2.9mm x 1.6mm
  • (1) For all available packages, see Section 9.
  • (2) The package size (length × width) is a nominal value and includes pins, where applicable.

Copyright © 2016, Texas Instruments Incorporated

  • A: Sleep Receiver and Wake Detect are device dependent options and are only available in TCAN334.
  • B: Fault Logic are only available in TCAN337.
  • C: Pin 5 and 8 functions are device dependent. Refer to Device Comparison Table.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
TCAN330Texas Instruments—
TCAN330/GTexas Instruments—
TCAN330DTexas Instruments8-SOIC (0.154", 3.90mm Width)
TCAN330D.BTexas InstrumentsSOIC-8
TCAN330DCNRTexas InstrumentsSOT-23-8
TCAN330DCNR.BTexas InstrumentsSOT-23-8
TCAN330DCNTTexas InstrumentsSOT-23-8
TCAN330DCNT.BTexas InstrumentsSOT-23-8
TCAN330DR.BTexas InstrumentsSOIC-8
TCAN330GTexas Instruments—
TCAN330GDTexas InstrumentsSOIC-8
TCAN330GD.BTexas InstrumentsSOIC-8
TCAN330GDCNRTexas InstrumentsSOT-23-8
TCAN330GDCNR.BTexas InstrumentsSOT-23-8
TCAN330GDCNTTexas InstrumentsSOT-23-8
TCAN330GDCNT.BTexas InstrumentsSOT-23-8
TCAN330GDG4Texas InstrumentsSOIC-8
TCAN330GDG4.BTexas InstrumentsSOIC-8
TCAN330GDRTexas InstrumentsSOIC-8
TCAN330GDR.BTexas InstrumentsSOIC-8
TCAN332Texas Instruments—
TCAN332GTexas Instruments—
TCAN334Texas Instruments—
TCAN334GTexas Instruments—
TCAN337Texas Instruments—
TCAN337GTexas Instruments—

Other Integrated Circuits

All Integrated Circuits datasheetsAll Texas Instruments datasheets (2,417)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TCAN330DR

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TCAN330DR run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.