NRF9151-LACA-R7

Part: nRF9151

Type: LTE-M/NB-IoT/DECT NR+ and GNSS System-in-Package with ARM Cortex-M33 MCU

Description: Low-power cellular IoT SiP integrating an Arm Cortex-M33 microcontroller with 1 MB flash and 256 KB RAM, LTE-M/NB-IoT modem, DECT NR+, and GPS receiver operating from 3.0 V to 5.5 V.

Operating Conditions:

• Supply voltage: 3.0 V to 5.5 V

Absolute Maximum Ratings:

• Max junction/storage temperature: -40 to 95 °C (Storage temperature)

Key Specs:

• LTE Cat-M1 sensitivity: -108 dBm (low band), -107 dBm (mid band)
• RF output power: Up to 23 dBm (Power Class 3), up to 20 dBm (Power Class 5)
• DECT NR+ transmit power: 21 dBm (Class II) on bands 1, 2, 9, 22; 19 dBm (Class III) on band 4
• LTE PSM floor current: 2.7 μA (at 3.7 V)
• eDRX current @ 81.92 s: 18 μA (Cat-M1), 32 μA (Cat-NB1) at 3.7 V (UICC included)
• Antenna input level: 10 dBm max (ANT), -15 dBm max (GPS, LNA turned on, max gain)
• ADC: 12-bit, 200 ksps, 8 configurable channels
• Flash endurance / retention: 10,000 write/erase cycles; 10 years at 85 °C

Features:

• Arm Cortex-M33 application processor with Arm TrustZone and Arm CryptoCell 310
• Multimode LTE-M, NB-IoT (3GPP Rel 14), and IoT NTN (3GPP Rel 17) modem
• Integrated GPS receiver supporting GPS L1 C/A and QZSS L1 C/A
• Support for DECT NR+
• Peripheral set including EasyDMA-supported SPI, I2C, UART, PDM, I2S, and PWM
• Single 50 Ω antenna interface
• 32 general-purpose I/O pins

Applications:

• Sensor networks
• Logistics and asset tracking
• Smart energy
• Smart building automation
• Smart agriculture

Package:

• LGA package (12.1 × 11.1 × 1.2 mm)

• Peripheral tasks can subscribe to channels

• Peripheral events can be published on channels

• Publish/subscribe pattern enabling multiple connection options that include the following:

• One-to-one

• One-to-many

• Many-to-one

• Many-to-many

The DPPI consists of several PPIBus modules, which are connected to a fixed number of DPPI channels and a DPPI configuration (DPPIC).

Figure 18: DPPI overview

• Sensor networks
• Logistics and asset tracking
• Smart energy
• Smart building automation
• Smart agriculture

The GPIO port peripheral implements up to 32 pins, PIN0 through PIN31 . Each of these pins can be individually configured in the PIN_CNF[n] registers (n=0..31).

The following parameters can be configured through these registers:

• Direction
• Drive strength
• Enabling of pull-up and pull-down resistors
• Pin sensing
• Input buffer disconnect
• Analog input (for selected pins)

Note: All write-capable registers are retained registers, see POWER - Power control on page 67 for more information.

The input buffer of a GPIO pin can be disconnected from the pin to enable power savings when the pin is not used as an input, see GPIO port and the GPIO pin details on page 163. Inputs must be connected to get a valid input value in the IN register, and for the sense mechanism to get access to the pin.

Other peripherals in the system can connect to GPIO pins and override their output value and configuration, or read their analog or digital input value. See GPIO port and the GPIO pin details on page 163.

Selected pins also support analog input signals, see ANAIN in GPIO port and the GPIO pin details on page 163. The assignment of the analog pins can be found in Pin assignments on page 518.

The following delays should be taken into considerations:

• There is a delay of 2 CPU clock cycles from the GPIO pad to the IN register.
• The GPIO pad must be low (or high depending on the SENSE polarity) for 3 CPU clock cycles after DETECT has gone high to generate a new DETECT signal.

Note: When a pin is configured as digital input, care has been taken to minimize increased current consumption when the input voltage is between VIL and VIH. However, it is a good practice to ensure that the external circuitry does not drive that pin to levels between VIL and VIH for a long period of time.

Maximum ratings are the extreme limits to which the chip can be exposed for a limited amount of time without permanently damaging it. Exposure to absolute maximum ratings for prolonged periods of time may affect the reliability of the device.

Table 62: Supply voltage

Table 63: I/O pin voltage

Table 64: Radio

Table 65: Environmental (LGA package)

2 AUX pin excluded.