MSP430F5526

Part: MSP430F5529IPN — Texas Instruments

Type: 16-bit Mixed-Signal Microcontroller (MSP430 with USB)

Description: 16-bit RISC MCU running at up to 25 MHz from a 1.8–3.6 V supply, with integrated full-speed USB, 12-bit ADC, four 16-bit timers, and 63 I/O pins in an 80-pin LQFP package.

Operating Conditions:

• Supply voltage: 1.8–3.6 V (minimum VCC rises with PMMCOREVx setting: 1.8 V at 0, 2.0 V at 1, 2.2 V at 2, 2.4 V at 3)
• Operating temperature: -40 to 85 °C (I version)
• Max processor frequency: 8 MHz (PMMCOREVx=0), 12 MHz (1), 20 MHz (2), 25 MHz (3)
• USB operation needs a minimum processor frequency of 1.5 MHz

Absolute Maximum Ratings:

• Supply voltage at VCC to VSS: -0.3 to 4.1 V
• Voltage applied to any pin (excluding VCORE, VBUS, V18): -0.3 V to VCC + 0.3 V
• Diode current at any device pin: ±2 mA
• Max operating junction temperature: 95 °C
• Storage temperature: -55 to 150 °C

Key Specs:

• Active mode current: 290 μA/MHz at 8 MHz, 3.0 V, flash execution (typical)
• Active mode current: 150 μA/MHz at 8 MHz, 3.0 V, RAM execution (typical)
• Standby (LPM3) with RTC: 1.9 μA at 2.2 V, 2.1 μA at 3.0 V (typical)
• LPM3 with VLO: 1.4 μA at 3.0 V (typical)
• LPM4 (off mode): 1.1 μA at 3.0 V (typical)
• LPM4.5 (shutdown): 0.18 μA at 3.0 V (typical)
• Wake-up from standby: 3.5 μs (typical)
• Recommended VCORE capacitor: 470 nF, with a DVCC/VCORE capacitor ratio of at least 10

Features:

• 16-bit RISC CPU with extended memory, up to 25 MHz system clock
• Integrated LDO with programmable core voltage, plus supply supervision, monitoring, and brownout
• Unified clock system with FLL, VLO, REFO, XT1 (32 kHz) and XT2 (up to 32 MHz)
• Timers: TA0 (5 CCRs), TA1 (3 CCRs), TA2 (3 CCRs), TB0 (7 CCRs)
• USCI_A0/A1: UART with auto-baud and IrDA, or SPI
• USCI_B0/B1: I2C or SPI
• Full-speed USB with integrated PHY, PLL, and 3.3 V/1.8 V power system; 8 input and 8 output endpoints
• 12-bit ADC with internal reference, sample-and-hold, and autoscan
• Comparator, 32-bit hardware multiplier, 3-channel DMA, RTC
• Serial onboard programming with no external programming voltage

Applications:

• Analog and digital sensor systems
• Data loggers
• Connection to USB hosts

Package:

• LQFP (80), 12 mm × 12 mm (MSP430F5529IPN)

• Low supply voltage range: 3.6 V down to 1.8 V
• Ultra-low power consumption
• -Active mode (AM):
• All system clocks active:
• -290 μA/MHz at 8 MHz, 3.0 V, flash program execution (typical)
• -150 μA/MHz at 8 MHz, 3.0 V, RAM program execution (typical)
• -Standby mode (LPM3):
• Real-time clock (RTC) with crystal, watchdog, and supply supervisor operational, full RAM retention, fast wakeup:
• -1.9 μA at 2.2 V, 2.1 μA at 3.0 V (typical)
• Low-power oscillator (VLO), generalpurpose counter, watchdog, and supply supervisor operational, full RAM retention, fast wakeup:
• -1.4 μA at 3.0 V (typical)
• -Off mode (LPM4):
• Full RAM retention, supply supervisor operational, fast wakeup:
• -1.1 μA at 3.0 V (typical)
• -Shutdown mode (LPM4.5):
• 0.18 μA at 3.0 V (typical)
• Wake up from standby mode in 3.5 μs (typical)
• 16-bit RISC architecture, extended memory, up to 25-MHz system clock
• Flexible power-management system
• -Fully integrated LDO with programmable regulated core supply voltage
• -Supply voltage supervision, monitoring, and brownout
• Unified clock system
• -FLL control loop for frequency stabilization
• -Low-power low-frequency internal clock source (VLO)
• -Low-frequency trimmed internal reference source (REFO)
• -32-kHz watch crystals (XT1)
• -High-frequency crystals up to 32 MHz (XT2)
• 16-bit timer TA0, Timer_A with five capture/ compare registers
• 16-bit timer TA1, Timer_A with three capture/ compare registers
• 16-bit timer TA2, Timer_A with three capture/ compare registers
• 16-bit timer TB0, Timer_B with seven capture/ compare shadow registers
• Two universal serial communication interfaces (USCIs)
• -USCI_A0 and USCI_A1 each support:
• Enhanced UART supports automatic baudrate detection
• IrDA encoder and decoder
• Synchronous SPI
• -USCI_B0 and USCI_B1 each support:
• I 2 C
• Synchronous SPI
• Full-speed universal serial bus (USB)
• -Integrated USB-PHY
• -Integrated 3.3-V and 1.8-V USB power system
• -Integrated USB-PLL
• -Eight input and eight output endpoints
• 12-bit analog-to-digital converter (ADC) (MSP430F552x only) with internal reference, sample-and-hold, and autoscan features
• Comparator
• Hardware multiplier supports 32-bit operations
• Serial onboard programming, no external programming voltage needed
• 3-channel internal DMA
• Basic timer with RTC feature
• Development tools and software (also see Tools and Software)
• -LaunchPad ™ development kit (MSP -EXP430F5529LP)
• -MSP430F5529 experimenter's board (MSP -EXP430F5529)
• -80-pin target development board (MSP -TS430PN80USB)
• -64-pin target development board (MSP -TS430RGC64USB)
• -USB developers package (MSP430USBDEVPACK)
• -MSP430Ware ™ code examples
• Device Comparison summarizes the available family members

• Analog and digital sensor systems
• Data loggers
• Connection to USB hosts

MSP430F5529

MSP430F5528

MSP430F5527

MSP430F5526

MSP430F5525

Product Folder Links:

MSP430F5524

MSP430F5522

MSP430F5521

MSP430F5519

MSP430F5517

MSP430F5515

MSP430F5514

MSP430F5513

1

www.ti.com

www.ti.com

over operating free-air temperature range (unless otherwise noted) (1)

NOTE: The numbers within the fields denote the supported PMMCOREVx settings.

Figure 8-1. Maximum System Frequency