MK22FN512VLL12

Part: MK22FN512VLH12 — NXP Type: ARM Cortex-M4 Microcontroller with FPU Description: 120 MHz ARM Cortex-M4 core with DSP instructions, 512 KB Flash, 128 KB RAM, USB connectivity, and low-power features.

Operating Conditions:

• Supply voltage: 1.71 to 3.6 V
• Operating temperature: -40 to 105 °C
• Max CPU frequency: 120 MHz

Absolute Maximum Ratings:

• Max supply voltage: 3.8 V
• Max continuous current: 169 mA (Digital supply current)
• Max junction/storage temperature: 150 °C

Key Specs:

• CPU Speed: 120 MHz
• Flash Memory: 512 KB
• RAM: 128 KB
• Run power consumption: down to 156 μA/MHz
• Lowest static mode power consumption: down to 140 nA
• ADC Resolution: Two 16-bit SAR ADCs
• DAC Resolution: Two 12-bit DACs
• USB VREG input voltage: -0.3 to 6 V
• Input leakage current (per pin): 0.002 μA (typ), 0.5 μA (max)

Features:

• 120 MHz Arm Cortex-M4 core with DSP instructions and FPU
• USB LS/FS OTG 2.0 with embedded 3.3 V, 120 mA LDO voltage regulator
• FlexBus external bus interface (package dependent)
• Serial programming interface (EzPort)
• Hardware CRC module and random-number generator
• Two 16-bit SAR ADCs (1.2 MS/s in 12-bit mode)
• Two 12-bit DACs (package dependent)
• Two SPI, three UART, two I2C, and I2S modules
• Up to 81 general-purpose I/O (GPIO)

Applications:

• Cost-sensitive applications requiring low-power
• Applications requiring USB connectivity
• Applications requiring processing efficiency and high peripheral integration

Package:

• 121 XFBGA (8x8x0.5mm)
• 100 LQFP (14x14x1.7mm)
• 64 LQFP (10x10x1.6mm)
• 64 MAPBGA (5x5x1.23mm)
• 88 QFN (10x10x0.9mm)

The following table shows the signals available on each pin and the locations of these pins on the devices supported by this document. The Port Control Module is responsible for selecting which ALT functionality is available on each pin.

NOTE The MK22FN512VFX12 (88QFN) does not support the FlexBus function.

64 MAP BGA	64 LQFP	88 QFN	100 LQFP	121 XFPB GA	Pin Name	Default	ALT0	ALT1	ALT2	ALT3	ALT4	ALT6	ALT7	EZPORT
A1	1	1	1	E4	PTE0/ CLKOUT3 2K	ADC1_ SE4a	ADC1_ SE4a	PTE0/ CLKOUT3 2K	SPI1_ PCS1	UART1_ TX		I2C1_SDA	RTC_ CLKOUT
B1	2	2	2	E3	PTE1/ LLWU_P0	ADC1_ SE5a	ADC1_ SE5a	PTE1/ LLWU_P0	SPI1_ SOUT	UART1_ RX		I2C1_SCL	SPI1_SIN
-	-	3	3	E2	PTE2/ LLWU_P1	ADC1_ SE6a	ADC1_ SE6a	PTE2/ LLWU_P1	SPI1_SCK	UART1_ CTS_b
-	-	4	4	F4	PTE3	ADC1_ SE7a	ADC1_ SE7a	PTE3	SPI1_SIN	UART1_ RTS_b			SPI1_ SOUT
-	-	5	5	H7	PTE4/ LLWU_P2	DISABLED		PTE4/ LLWU_P2	SPI1_ PCS0	LPUART0_ TX
-	-	6	6	G4	PTE5	DISABLED		PTE5	SPI1_ PCS2	LPUART0_ RX		FTM3_ CH0
-	-	7	7	F3	PTE6	DISABLED		PTE6	SPI1_ PCS3	LPUART0_ CTS_b	I2S0_ MCLK	FTM3_ CH1	USB_ SOF_OUT
C5	3	8	8	E6	VDD	VDD	VDD
C4	4	9	9	G7	VSS	VSS	VSS
-	-	9	-	L6	VSS	VSS	VSS
E1	5	10	10	F1	USB0_DP	USB0_DP	USB0_DP
D1	6	11	11	F2	USB0_DM	USB0_DM	USB0_DM
E2	7	12	12	G1	VOUT33	VOUT33	VOUT33
D2	8	13	13	G2	VREGIN	VREGIN	VREGIN
-	-	-	14	H1	ADC0_ DP1	ADC0_ DP1	ADC0_ DP1
-	-	-	15	H2	ADC0_ DM1	ADC0_ DM1	ADC0_ DM1

Unless otherwise specified, propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured at the 20% and 80% points, as shown in the following figure.

Figure 2. Input signal measurement reference

Symbol	Description	Min.	Max.	Unit	Notes
T STG	Storage temperature	-55	150	°C	1
T SDR	Solder temperature, lead-free	-	260	°C	2

Package dimensions are provided in package drawings.

To find a package drawing, go to nxp.com and perform a keyword search for the drawing's document number:

If you want the drawing for this package	Then use this document number
64-pin LQFP	98ASS23234W
64-pin MAPBGA	98ASA00420D
88-pin QFN	98ASA00935D
100-pin LQFP	98ASS23308W
121-pin XFBGA	98ASA00595D