LMV358/358I
Dual Rail-to-Rail CMOS Op AmpThe LMV358/358I is a dual rail-to-rail cmos op amp from Texas Instruments. View the full LMV358/358I datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
LMV358/358I shares its datasheet with LMV358I, whose page lists every part number it covers.
Official LMV358/358I datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Integrated CircuitsLMV358/358I Key Specifications
| Parameter | Value |
|---|---|
| CMRR | 65 dB typ (5V) |
| PSRR | 60 dB typ |
| Slew Rate | 1 V/µs |
| Phase Margin | 60° |
| Interface/Output | Rail-to-rail output |
| Input Bias Current | <1 nA |
| Number Of Channels | 2 |
| Input Offset Voltage | 1.7 mV typ, 9 mV max |
| Supply Voltage Range | 2.7V to 5.5V |
| Gain Bandwidth Product | 1 MHz |
| Input Common-Mode Range | -0.2V to 4.2V (5V supply) |
| Input-Referred Voltage Noise | 50 nV/√Hz at 50 kHz |
| Output Short Circuit Current | 60 mA source, 160 mA sink typ |
| Operating Temperature (LMV358) | -40°C to 85°C |
| Operating Temperature (LMV358I) | -40°C to 125°C |
| Supply Current (5V, Both Amplifiers) | 210 µA typ, 440 µA max |
| Supply Current (2.7V, Both Amplifiers) | 140 µA typ, 340 µA max |
LMV358/358I Overview
Part: LMV358 / LMV358I (dual) — onsemi (LMV321/LMV324/NCV321 family)
Type: Dual Low-Voltage Rail-to-Rail CMOS Operational Amplifier
Description: 2.7–5.5 V, dual CMOS op amp with rail-to-rail output, 1 MHz gain-bandwidth product and about 210 μA typical supply current (both amplifiers) at 5 V.
Operating Conditions:
- Supply voltage: 2.7–5.5 V (specified at 2.7 V and 5 V)
- Operating temperature: -40 to 85 °C for LMV358; -40 to 125 °C for LMV358I
- Input common-mode range includes ground (0 to 4 V guaranteed at V+ = 5 V for CMRR ≥ 50 dB)
Absolute Maximum Ratings:
- Max supply voltage: 5.5 V
- Max input current: 10 mA
- Input common-mode voltage range: -0.5 to (V+) + 0.5 V
- Max junction temperature: 150 °C
- Storage temperature: -65 to 150 °C
- ESD (LMV358/358I/324): HBM 2000 V, MM 100 V
Key Specs:
- Input offset voltage: 1.7 mV typ, 9 mV max (V+ = 5 V, TA = TLow to THigh)
- Input bias current: <1 nA typ
- Supply current, LMV358/358I (both amplifiers): 210 μA typ, 440 μA max at 25 °C (V+ = 5 V); 140 μA typ, 340 μA max at 2.7 V
- Gain bandwidth product: 1 MHz (CL = 200 pF)
- Slew rate: 1 V/μs (V+ = 5 V)
- Phase margin: 60°; gain margin: 10 dB
- CMRR: 65 dB typ (50 dB min); PSRR: 60 dB typ (50 dB min)
- Output swing at 5 V, RL = 10 kΩ: VOH ≥ VCC - 100 mV, VOL 65 mV typ (180 mV max)
- Output short-circuit current at 5 V: 60 mA typ sourcing, 160 mA typ sinking (10 mA min each)
- Input-referred voltage noise: 50 nV/√Hz at 50 kHz
Features:
- Operation from 2.7 V to 5.0 V single-sided supply
- Rail-to-rail output
- No output crossover distortion
- No output phase reversal from overdriven input
- Low quiescent current (LMV358 dual: 220 μA max per channel)
- Pb-free, halogen-free/BFR-free, RoHS compliant
- NCV prefix for automotive: AEC-Q100 qualified and PPAP capable (NCV321)
Applications:
- Portable battery-operated instruments
- Notebook computers and PDAs
- Active filters
Package:
- SOIC-8 (LMV358DR2G, LMV358IDR2G; 2500/reel)
- Micro8 (LMV358DMR2G; 4000/reel)
- UDFN8, 1.2 × 1.8 × 0.5 mm (LMV358MUTAG; 3000/reel)
LMV358/358I Features
- LMV321 Single Available in Ultra Small 5 Pin SC70 Package
- Operation from 2.7 V to 5.0 V Single -Sided Power Supply
- No Output Crossover Distortion
- Low Quiescent Current: LMV358 Dual -220 m A, Max per Channel
- Rail -to -Rail Output
- No Output Phase -Reversal from Overdriven Input
- These Devices are Pb -Free, Halogen Free/BFR Free and are RoHS Compliant
- NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC -Q100 Qualified and PPAP Capable
LMV358/358I Applications
- Portable Battery -Operated Instruments
- Notebook Computers and PDA's
- Active Filters
LMV358/358I Electrical Characteristics
| Parameter | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Gain Bandwidth Product | GBWP | C L = 200 pF | 1 | MHz | ||
| Phase Margin | Q m | 60 | ° | |||
| Gain Margin | G m | 10 | dB | |||
| Input - Referred Voltage Noise | e n | f = 50 kHz | 50 | nV/ √ Hz |
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions.
- For LMV321, LMV358, LMV324: T A = -40 C to +85 C For LMV321I, LMV358I, NCV321: T A = -40 ° C to +125 ° C.
° °
- Guaranteed by design and/or characterization.
5.0 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for T A = 25 ° C, V + = 5.0 V, RL = 1 M W , V -= 0 V, V O = V+/2)
| Parameter | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Input Offset Voltage | V IO | T A = T Low to T High (Note 6) | 1.7 | 9 | mV | |
| Input Offset Voltage Average Drift | T C V IO | T A = T Low to T High (Note 6) | 5 | m V/ ° C | ||
| Input Bias Current (Note 7) | I B | T A = T Low to T High (Note 6) | < 1 | nA | ||
| Input Offset Current (Note 7) | I IO | T A = T Low to T High (Note 6) | < 1 | nA | ||
| Common Mode Rejection Ratio | CMRR | 0 V v V CM v 4 V | 50 | 65 | dB | |
| Power Supply Rejection Ratio | PSRR | 2.7 V v V+ v 5 V, V O = 1 V, V CM = 1 V | 50 | 60 | dB | |
| Input Common - Mode Voltage Range | V CM | For CMRR w 50 dB | 0 to 4 | - 0.2 to 4.2 | V | |
| Large Signal Voltage Gain (Note 7) | A V | R L = 2 k W | 15 | 100 | V/mV | |
| Output Swing | T A = T Low to T High (Note 6) | 10 | V/mV | |||
| V OH | R L = 2 k W to 2.5 V T A = T Low to T High (Note 6) | V CC - 300 V CC - 400 | V CC - 40 | mV | ||
| V OL | R L = 2 k W to 2.5 V (Note 7) T A = T Low to T High (Note 6) | 120 | 300 400 | mV | ||
| V OH | R L = 10 k W to 2.5 V (Note 7) T A = T Low to T High (Note 6) | V CC - 100 V CC - 200 | mV | |||
| V OL | R L = 10 k W to 2.5 V T A = T Low to T High (Note 6) | 65 | 180 280 | mV | ||
| Output Short Circuit Current | I O | Sourcing = V O = 0 V (Note 7) Sinking = V O = 5 V (Note 7) | 10 10 | 60 160 | mA | |
| Supply Current | I CC | LMV321 T A = T Low to T High (Note 6) | 130 | 250 350 | m A | |
| Supply Current | NCV321 T A = T Low to T High (Note 6) | 130 | 250 350 | m A | ||
| Supply Current | LMV358/358I Both Amplifiers T A = T Low to T High (Note 6) | 210 | 440 615 | m A | ||
| Supply Current | LMV324 All Four Amplifiers T A = T Low to T High (Note 6) | 410 | 830 1160 | m A |
5.0 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for T A = 25 ° C, V + = 5.0 V, RL = 1 M W , V -= 0 V, V O = V+/2)
| Parameter | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Slew Rate | S R | 1 | V/ m s | |||
| Gain Bandwidth Product | GBWP | C L = 200 pF | 1 | MHz | ||
| Phase Margin | Q m | 60 | ° | |||
| Gain Margin | G m | 10 | dB | |||
| Input - Referred Voltage Noise | e n | f = 50 kHz | 50 | nV/ √ Hz |
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions.
- For LMV321, LMV358, LMV324: T A = -40 C to +85 C
For LMV321I, LMV358I, NCV321: T A = -40 C to +125 C.
° ° ° °
- Guaranteed by design and/or characterization.
(T A = 25 ° C and V S = 5 V unless otherwise specified)
(T A = 25 ° C and V S = 5 V unless otherwise specified)
(T A = 25 ° C and V S = 5 V unless otherwise specified)
(T A = 25 ° C and V S = 5 V unless otherwise specified)
Figure 19. Source Current vs. Output Voltage VS = 5.0 V
Figure 21. Settling Time vs. Capacitive Load
Figure 20. Settling Time vs. Capacitive Load
Figure 22. Step Response -Small Signal
Figure 23. Step Response -Small Signal
Figure 24. Step Response -Large Signal
(T A = 25 ° C and V S = 5 V unless otherwise specified)
Figure 25. Step Response -Large Signal
LMV358/358I Absolute Maximum Ratings
| Symbol | Rating | Value | Unit |
|---|---|---|---|
| V S | Supply Voltage (Operating Range V S = 2.7 V to 5.5 V) | 5.5 | V |
| V IDR | Input Differential Voltage | $ Supply Voltage | V |
| V ICR | Input Common Mode Voltage Range | - 0.5 to (V+) + 0.5 | V |
| Maximum Input Current | 10 | mA | |
| t So | Output Short Circuit (Note 1) | Continuous | |
| T J | Maximum Junction Temperature | 150 | ° C |
| T A | Operating Ambient Temperature Range LMV321, LMV358, LMV324 LMV321I, LMV358I NCV321 (Note 2) | - 40 to 85 - 40 to 125 - 40 to 125 | ° C ° C ° C |
| q JA | Thermal Resistance: | ° C/W | |
| q JA | SC - 70 | 280 | |
| q JA | Micro8 | 238 | |
| q JA | TSOP - 5 | 333 | |
| q JA | UDFN8 (1.2 mmx 1.8 mmx 0.5 mm) | 350 | |
| q JA | SOIC - 8 | 212 | |
| q JA | SOIC - 14 | 156 | |
| q JA | TSSOP - 14 | 190 | |
| T stg | Storage Temperature | - 65 to 150 | ° C |
| Mounting Temperature (Infrared or Convection - 20 sec) | 260 | ° C | |
| V ESD | ESD Tolerance (Note 3) LMV321, LMV321I, NCV321 Machine Model Human Body Model LMV358/358I/324 Machine Model Human Body Mode | 100 1000 100 2000 | V |
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected.
-
Continuous short -circuit operation to ground at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150 ° C. Output currents in excess of 45 mA over long term may adversely affect reliability. Shorting output to either V+ or V -will adversely affect reliability.
-
NCV prefix is qualified for automotive usage.
-
Human Body Model, applicable std. MIL -STD -883, Method 3015.7 Machine Model, applicable std. JESD22 -A115 -A (ESD MM std. of JEDEC) Field -Induced Charge -Device Model, applicable std. JESD22 -C101 -C (ESD FICDM std. of JEDEC).
2.7 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for T A = 25 ° C, V + = 2.7 V, RL = 1 M W , V -= 0 V, V O = V+/2)
| Parameter | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Input Offset Voltage | V IO | T A = T Low to T High (Note 4) | 1.7 | 9 | mV | |
| Input Offset Voltage Average Drift | ICV OS | T A = T Low to T High (Note 4) | 5 | m V/ ° C | ||
| Input Bias Current | I B | T A = T Low to T High (Note 4) | <1 | nA | ||
| Input Offset Current | I IO | T A = T Low to T High (Note 4) | <1 | nA | ||
| Common Mode Rejection Ratio | CMRR | 0 V v V CM v 1.7 V | 50 | 63 | dB | |
| Power Supply Rejection Ratio | PSRR | 2.7 V v V+ v 5 V, V O = 1 V | 50 | 60 | dB | |
| Input Common - Mode Voltage Range | V CM | For CMRR w 50 dB | 0 to 1.7 | - 0.2 to 1.9 | V | |
| Output Swing | V OH | R L = 10 k W to 1.35 V | V CC - 100 | V CC - 10 | mV | |
| Output Swing | V OL | R L = 10 k W to 1.35 V (Note 5) | 60 | 180 | mV | |
| Supply Current LMV321, NCV321 LMV358/LMV358I (Both Amplifiers) LMV324 (4 Amplifiers) | I CC | 80 140 260 | 185 340 680 | m A |
LMV358/358I Typical Application
- Portable Battery -Operated Instruments
- Notebook Computers and PDA's
- Active Filters
LMV358/358I Package Information
| DIM | MILLIMETERS - MIN | MILLIMETERS - MAX | INCHES - MIN | INCHES - MAX |
|---|---|---|---|---|
| A | 4.80 | 5.00 | 0.189 | 0.197 |
| B | 3.80 | 4.00 | 0.150 | 0.157 |
| C | 1.35 | 1.75 | 0.053 | 0.069 |
| D | 0.33 | 0.51 | 0.013 | 0.020 |
| G | 1.27 BSC | 1.27 BSC | 0.050 BSC | 0.050 BSC |
| H | 0.10 | 0.25 | 0.004 | 0.010 |
| J | 0.19 | 0.25 | 0.007 | 0.010 |
| K | 0.40 | 1.27 | 0.016 | 0.050 |
| M | 0 _ | 8 _ | 0 _ | 8 _ |
| N | 0.25 | 0.50 | 0.010 | 0.020 |
| S | 5.80 | 6.20 | 0.228 | 0.244 |
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| LMV358 | Texas Instruments | — |
| LMV358/358I/324 | Texas Instruments | — |
| LMV358DMR2G | Texas Instruments | Micro8 |
| LMV358DR2G | Texas Instruments | SOIC-8 |
| LMV358I | Texas Instruments | — |
| LMV358IDR | Texas Instruments | 8-SOIC (0.154", 3.90mm Width) |
| LMV358IDR2G | Texas Instruments | SOIC-8 |
| LMV358MUTAG | Texas Instruments | UDFN8 |
Other Integrated Circuits
- STM32F103C8T6 – STMicroelectronics, Microcontroller
- STM32F405RGT6 – STMicroelectronics, ARM Cortex-M4 MCU
- SN74AVC4T245PWR – Texas Instruments, Dual-Supply Bus Transceiver Level Translator
- STM32F446RCT6 – STMicroelectronics, ARM Cortex-M4 MCU
- STM32G070RBT6 – STMicroelectronics, Arm Cortex-M0+ 32-bit MCU
- ADS131M08IPBSR – Texas Instruments, Delta-Sigma ADC
- ISO1540DR – Texas Instruments, Bidirectional I²C Isolator
- ISO7740DBQR – Texas Instruments, Digital Isolator
All Integrated Circuits datasheetsAll Texas Instruments datasheets (2,442)
Ask your AI agent about the LMV358/358I
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the LMV358/358I run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.