Power Management Datasheets
219 Power Management datasheets read into specs, pinouts and ratings. Parts from Texas Instruments, Analog Devices and Diodes.
Power Management datasheets, page 3
219 parts · page 3 of 8. Most used first, then by part number.
EFP0101
Silicon Labs
Ultra-low quiescent current multi-output PMIC with buck/boost DC-DC, buck DC-DC, LDO outputs and lossless Coulomb counter for primary cell battery systems; EFP0101 is the wired-buck variant with VOB enabled at 1.858 V at startup.
EFP0102
Silicon Labs
Ultra-low-power multi-output PMIC with buck/boost DC-DC, buck DC-DC, LDOs and Coulomb counter for EFM32/EFR32 devices; EFP0102 is the wired-buck configuration with VOB disabled at startup.
EFP0103
Silicon Labs
Ultra-low-power multi-output PMIC with buck/boost and buck DC-DC converters, LDOs, switched output, and lossless Coulomb counter for EFM32/EFR32 systems; EFP0103 is the wired buck with LDO C configuration.
EFP0104
Silicon Labs
Multi-output PMIC with buck DC-DC, LDO outputs, switched output and lossless Coulomb counter for powering EFM32/EFR32 devices from primary cells or USB; EFP0104 is the wired buck with LDO C variant with VOB disabled at startup.
EFP0106
Silicon Labs
Energy-friendly multi-output PMIC (Buck/Boost DC-DC, Buck DC-DC, LDO) with lossless Coulomb counter for EFM32/EFR32 systems, configured for Buck/Boost operation with VOB enabled at 1.858 V at startup
FAN7530
Not explicitly stated, but typically Fairchild/ON Semiconductor for FAN series
Critical conduction mode (CRM) boost PFC controller with voltage-mode PWM, over-voltage/over-current/open-feedback protection, and internal THD optimizer. The datasheet is for FAN7930C; FAN7530 is the older predecessor it is compared agains
FAN7530C
Not explicitly stated, but typically Fairchild/ON Semiconductor for FAN series
Active power factor correction controller for boost PFC applications operating in critical conduction mode (CRM), using voltage-mode PWM with internal THD optimizer and protection features.
FAN7888
onsemi
Monolithic three half-bridge gate-drive IC for driving MOSFETs and IGBTs up to +200 V, with 350 mA/650 mA source/sink current, built-in shoot-through prevention and UVLO, for 3-phase motor drive.
FAN7930B
Not explicitly stated, but typically Fairchild/ON Semiconductor for FAN series
Critical conduction mode (CRM) active power factor correction controller for boost PFC applications with voltage-mode PWM, internal THD optimizer, OVP, OCP, ZCD and a PFC-ready signal.
FAN7930C
Not explicitly stated, but typically Fairchild/ON Semiconductor for FAN series
Voltage-mode critical conduction mode (CRM) boost power factor correction controller with THD optimizer, OVP, OCP, open-feedback protection and PFC-ready signal.
FAN7930CMX-G
Not explicitly stated, but typically Fairchild/ON Semiconductor for FAN series
Active power factor correction controller for critical conduction mode (CRM) boost PFC using voltage-mode PWM with variable on-time control, OVP, OCP, open-feedback protection, and PFC-ready output
FM2113D
SHEN ZHEN FINE MADE ELECTRONICS GROUPCO., LTD.
High-precision single-cell Li-ion/Li-polymer battery protection IC with over-charge, over-discharge, over-current and short-circuit protection and internal delay timers
HLK-PM09
Hi-Link
3W ultra-small encapsulated AC-DC power module with 9V/330mA output, universal 85-265Vac input, isolation, short-circuit and over-current protection
HLK-PM12
Hi-Link
3W ultra-small encapsulated AC-DC power module with 12V/250mA output, universal 85-265Vac input, 3000Vac isolation, short-circuit and over-current protection
HLK-PM15
Hi-Link
3W ultra-small encapsulated AC-DC isolated power module with 15V/200mA output, universal 85-265Vac input, and short-circuit/over-current protection
HLK-PM24
Hi-Link
3W ultra-small encapsulated AC-DC power module with 24V/125mA output, universal 85-265Vac input, 3000Vac isolation, short-circuit and over-current protection.
HR051067
HanRun Electronics
Isolated flyback power transformer with primary, bias and secondary windings for a 36-72V input, 5V 1.4A output converter, with 1500Vrms primary-to-secondary isolation
IR2110
Infineon Technologies
High voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 500V (IR2110) floating channel, 2A source/sink
IR2110-1
Infineon Technologies
High voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 500V offset, 2A output current
IR2110-1PBF
Infineon Technologies
500V high-voltage, high-speed power MOSFET and IGBT driver with independent high- and low-side referenced output channels, 2A peak drive and bootstrap operation.
IR2110-2
Infineon Technologies
High voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 500V floating channel, 2A peak output current
IR2110PBF
Infineon Technologies
500V high-voltage, high-speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 2A source/sink drive current, and 3.3V logic compatibility
IR2110SPBF
Infineon Technologies
500V high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 2A source/sink drive current
IR2110STRPBF
International Rectifier
High voltage (500V), high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, 2A source/sink, 3.3V logic compatible
JY01
Not specified (project document, not a component datasheet)
JY01 is a brushless DC motor controller IC found on cheap JYQD_V6 three-phase driver boards; in this document it is removed so an STM32 NUCLEO-F401RE can drive the JY21L MOSFET drivers directly.
JY21L
Not specified (project document, not a component datasheet)
JY21L is a high-speed power MOSFET driver IC used on cheap JYQD_V6 BLDC driver boards; three of them drive the six MOSFETs of a three-phase brushless motor driver controlled by an STM32 NUCLEO board.
JYQD_V6
Not specified (project document, not a component datasheet)
Low-cost three-phase brushless DC motor driver board using three JY21L high-speed power MOSFET drivers and six MOSFETs, with the JY01 BLDC IC removed so it can be driven by an external microcontroller (STM32 NUCLEO-F401RE) via PWM and GPIO
L298HN
STMicroelectronics
High-voltage, high-current dual full-bridge driver accepting TTL logic levels for driving inductive loads such as DC motors, stepper motors, relays and solenoids
L298N
STMicroelectronics
IC HALF BRIDGE DRVR 15MULTIWATT
L298P
STMicroelectronics
High-voltage, high-current dual full-bridge driver accepting TTL logic levels for driving inductive loads such as relays, solenoids, DC and stepper motors.