TDA7706CB
AM/FM Car-Radio Tuner ICThe TDA7706CB is a am/fm car-radio tuner ic from STMicroelectronics. View the full TDA7706CB datasheet below including key specifications.
TDA7706CB shares its datasheet with TDA7706, whose page lists every part number it covers.
Official TDA7706CB datasheet (PDF) — the source this page was extracted from.
Manufacturer
STMicroelectronicsCategory
RF / WirelessTDA7706CB Key Specifications
| Parameter | Value |
|---|---|
| AM LNA Gain | 26 dB typ. (with 470 ohm) |
| Core Supply | 1.2 V (internal regulator) |
| IO Ring Supply | 3.3 V |
| Supply Voltage | 5 V (single supply) |
| Reception Bands | FM, AM (LW, MW, SW), Weather band |
| Control Interface | I2C |
| Crystal Frequency | 36.48 MHz fundamental |
| PLL Settling Time | approx. 100 us |
| PLL Frequency Step | 5 kHz (FM), 500 Hz (AM) |
| Package Dimensions | 10x10x1.4 mm |
| VCO Center Frequency | approx. 2.7 GHz |
| Audio DAC Dynamic Range | >100 dB |
| Digital Audio Interface | I2S input/output |
| IF ADC Sampling Frequency | 36.48 MHz |
| FM PIN Diode Drive Current | up to 15 mA |
TDA7706CB Overview
Part: TDA7706 — STMicroelectronics
Type: Highly integrated tuner for AM/FM car-radio
Description: The TDA7706 is a highly integrated AM/FM tuner IC for car-radio applications, suitable for HD Radio™ reception, featuring a fully integrated VCO and PLL synthesizer, digital IF processing, stereo decoder, RDS decoder, and digital interfaces.
Operating Conditions:
- Supply voltage: 5 V
- Crystal oscillator frequency: 36.48 MHz
- PLL settling time: ~100 μs (for fast RDS applications)
Key Specs:
- VCO center frequency: Approximately 2.7 GHz
- PLL frequency step: 5 kHz (FM), 500 Hz (AM)
- PIN diode driver current: up to 15 mA
- AM LNA maximum gain: 26 dB (with 470 ohm external resistor)
- IFADC sampling frequency: 36.48 MHz
- Audio DAC dynamic range: >100 dB
Features:
- FM, AM and weather band reception
- Fully integrated VCO for world tuning
- High performance PLL for fast RDS system
- Integrated AM-LNA and PIN diodes
- Automatic self alignment for FM front-end preselection filter and image rejection
- Integrated IF filters with high selectivity, dynamic range and adaptive bandwidth control
- Drift-free Digital-IF signal processing with high performance
- RDS demodulation with group and block synchronization
- High performance stereo decoder with noiseblanker
- Digital interface for HD Radio™ reception with digital audio blending
- Fully programmable DSP core
- I2C bus-controlled
- I2S input/output digital audio interfaces
- Single 5 V supply
Applications:
- Car-radio applications
- HD Radio™ reception
Package:
- LQFP64 (10x10x1.4mm)
TDA7706CB Features
- ■ FM, AM and weather band reception
- ■ Fully integrated VCO for world tuning
- ■ High performance PLL for fast RDS system
- ■ Integrated AM-LNA and PIN diodes
- ■ Automatic self alignment for FM front-end preselection filter and image rejection
- ■ Integrated IF filters with high selectivity, dynamic range and adaptive bandwidth control
- ■ Drift-free Digital-IF signal processing with high performance
- ■ RDS demodulation with group and block synchronization
- ■ High performance stereo decoder with noiseblanker
- ■ Digital interface for HD Radio™ reception with digital audio blending
- ■ Fully programmable DSP core
- ■ I 2 C bus-controlled
- ■ I 2 S input/output digital audio interfaces
- ■ Single 5 V supply
- ■ LQFP64 package
TDA7706CB Pin Configuration
Figure 2. Pin connection (top view)
Table 2. Pin description
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 1 | FMPINDRV | Out | FM | FM PIN diode driver output | |
| 2 | FMPINDdec | In | FM | Integrated FM PINdiode decoupling | '!0'03 |
| 3 | FMMIXdec | - | FM | FM RF signal ground | |
| 4 | FMMIXin2 | In | FM | FM mixer input 2 | |
| 5 | FMMIXin1 | In | FM | FM mixer input 1 | '!0'03 |
| 6 | GNDRF | - | - | RF power ground | - |
Table 2. Pin description
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 7 | TCAM | - | - | AM AGC time constant | '!0'03 |
| 8 | VCCRF | In | - | RF 5V supply | - |
| 9 | CK_SEL | In | - | Master/Slave clock operation select | '!0'03 |
| 10 | GNDVCO | - | VCO | VCO ground | - |
| 11 | LFref | - | VCO | Loop filter reference | - |
| 12 | LF1 | - | VCO | Loop filter output | - |
| 13 | VCCVCO | In | VCO | VCO 5V supply | - |
| 14 | TCAM2 | - | VCO | AM AGC 2 nd order time constant | '!0'03 |
| 15 | PINDdec | - | AM pin diode | AM AGC internal PIN diode decoupling | |
| 16 | PINDin | - | AM pin diode | AM AGC internal PIN diode input | |
| 17 | GNDLNA | - | AM LNA | AM LNA ground | - |
| 18 | LNAin | In | AM LNA | AM LNA input | |
| 19 | LNAdec | - | AM LNA | AM LNA decoupling | |
| 20 | LNAout | Out | AM LNA | AM LNA output | - |
| 21 | LNAin2 | - | AM LNA | AM LNA input 2 nd stage | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 22 | LNAout2 | - | AM LNA | AM LNA output 2 nd stage | |
| 23 | LNAdec2 | - | AM LNA | AM LNA decoupling 2 nd stage | |
| 24 | AMMIXin1 | In | AM mixer inputs | AM mixer input 1 | '!0'03 |
| 25 | AMMIXin2 | In | AM mixer inputs | AM mixer input 2 | '!0'03 |
| 26 | GNDSLINK | - | Supply, ground and reset | Internal inter-IC communication bus ground | - |
| 27 | Vdig | In | Supply, ground and reset | Front-end digital 5 V supply | - |
| 28 | VCCreg1V2 | In | Supply, ground and reset | Internal 1.2 V regulator 5 V supply | - |
| 29 | REG1V2 | Out | Supply, ground and reset | Internal 1.2 V regulator output | |
| 30 | Vreg3v3 | Out | Supply, ground and reset | Internal 3.3 V regulator output | |
| 31 | RSTN | In | Supply, ground and reset | Reset (low active) Pull-up 50 k to 3.3 V IO supply | |
| 32 | RDSint | Out | Supply, ground and reset | RDS interrupt output Pull-down 50 k to ground | - |
| 33 | I2CSDA | In/Out | I 2 C interface | I 2 C bus data Pull-up 50 k to 3.3 V IO supply | |
| 34 | I2CSCL | In | I 2 C interface | I 2 C bus clock Pull-up 50 k to 3.3 V IO supply | |
| 35 | VDD3V3 | In | - | IO ring (3.3V) supply | - |
| 36 | GND3V3 | - | - | IO ring (3.3V) supply | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 37 | GPIO8 In/Out | HD Radio connectivity/ Audio output I2S interface | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | '!0'03 | |
| 38 | GPIO7 | In/Out | Audio SAI word-select Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | |
| 39 | In/Out | Audio SAI data-output Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO6 | |
| 40 | In/Out | Audio SAI data-input Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO5 | |
| 41 | In/Out | SAI Base-Band clock Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO4 | |
| 42 | In/Out | SAI Base-Band word-select Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO3 | |
| 43 | Out | SAI Base-Band I data Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO2 | |
| 44 | Out | SAI Base-Band Q data Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO1 | |
| 45 | In | HD blend Pull-down 50 k to ground | GPIO0 | ||
| 46 | GND1V2 - | - | DSP core ground | - | |
| 47 | VDD core 1V2 | In - | DSP core 1.2V supply | - | |
| 48 | Test | In - | Test Mode Pull-down 50 k to ground | ||
| 49 | VDDPLL1V2 | In | - | Digital PLL 1.2 V supply | - |
| 50 | VDDIO1V2 | In | - | Internal inter-IC communication 1.2V supply | - |
| 51 | VCC-REF | In | - | Front-end reference frequency and regulator 5 V supply | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 52 | OSCin | In | Oscillator | Crystal oscilllator input | - |
| 53 | OSCout | Out | Oscillator | Crsystal oscillator output | |
| 54 | GND-REF | - | - | Front-end reference frequency and regulator ground | - |
| 55 | Vrefdec | - | - | 3.3 V Bias generation decoupling | |
| 56 | GND-ADC_DAC | - | DAC | IFADC and audio DAC ground | - |
| 57 | DACoutL | Out | DAC | Audio output left | |
| 58 | DACoutR | Out | DAC | Audio output right | |
| 59 | VCC-ADC_DAC | In | DAC | IFADC and audio DAC 5V supply | - |
| 60 | VCC-PLL | In | PLL | Tuning PLL 5V supply | - |
| 61 | GND-PLL | - | PLL | Tuning PLL ground | - |
| 62 | PLLtest | Out | PLL | PLL Test output | |
| 63 | TCFM | - | - | FM AGC time constant | |
| 64 | TVDAC | Out | - | Tuning voltage output | - |
Table 2. Pin description (continued)
TDA7706CB Typical Application
Figure 6. FM wide-band application
TDA7706CB Package Information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com .
ECOPACK ® is an ST trademark.
| $)- | MM | MM | MM | INCH | INCH | INCH |
|---|---|---|---|---|---|---|
| $)- | -). | 490 | -!8 | -). | 490 | -!8 |
| ! | ||||||
| ! | ||||||
| ! | ||||||
| " | ||||||
| # | ||||||
| $ | ||||||
| $ | ||||||
| $ | ||||||
| E | ||||||
| % | ||||||
| % | ||||||
| % | ||||||
| , | ||||||
| , | ||||||
| + | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ |
| CCC |
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| TDA7706 | STMicroelectronics | — |
Other RF / Wireless
- ST25DV04KC-IE6S3 – STMicroelectronics, Dynamic NFC/RFID Tag IC
- SX1276 – Semtech, Low Power Long Range Transceiver
- XA2214-S14 – Xinluda Information Technology Co., Ltd, GaAs MMIC SPDT Switch
- CC1101 – Texas Instruments, RF Transceiver
- EG915UEUAC-N05-SNNSA – Quectel, LTE Cat 1 Cellular Module
- ESP32-S3 – Espressif Systems, Wireless SoC
- SMTSO2515CTJ – Sinhoo, Surface Mount Nut
- ESP32-WROOM-32 – Espressif Systems, Wi-Fi+BT+BLE MCU module
All RF / Wireless datasheetsAll STMicroelectronics datasheets (808)
Ask your AI agent about the TDA7706CB
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the TDA7706CB run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.