TDA7706
AM/FM Car-Radio Tuner ICThe TDA7706 is a am/fm car-radio tuner ic from STMicroelectronics. View the full TDA7706 datasheet below including key specifications.
Official TDA7706 datasheet (PDF) — the source this page was extracted from.
Manufacturer
STMicroelectronicsCategory
RF / WirelessTDA7706 Key Specifications
| Parameter | Value |
|---|---|
| Package | LQFP64 (10x10x1.4 mm) |
| AM LNA Gain | 26 dB typical (with 470 ohm) |
| Other Features | RDS demodulation, HD Radio interface, 2 DSP cores |
| Supply Voltage | 5 V single supply (3.3 V IO ring, 1.2 V DSP core internally regulated) |
| Reception Bands | FM, AM (LW/MW/SW), Weather band |
| Control Interface | I2C |
| Crystal Frequency | 36.48 MHz fundamental |
| PLL Settling Time | approx. 100 us |
| PLL Frequency Step | 5 kHz (FM), 500 Hz (AM) |
| VCO Center Frequency | approx. 2.7 GHz |
| IF ADC Input Bandwidth | up to 325 kHz |
| Audio DAC Dynamic Range | >100 dB |
| Digital Audio Interface | I2S input/output |
| IF ADC Sampling Frequency | 36.48 MHz |
| FM PIN Diode Driver Current | up to 15 mA |
TDA7706 Overview
Part: TDA7706 — STMicroelectronics
Type: Highly integrated tuner for AM/FM car-radio
Description: The TDA7706 is a highly integrated AM/FM tuner IC for car-radio applications, suitable for HD Radio™ reception, featuring a fully integrated VCO and PLL synthesizer, digital IF processing, stereo decoder, RDS decoder, and digital interfaces.
Operating Conditions:
- Supply voltage: 5 V
- Crystal oscillator frequency: 36.48 MHz
- PLL settling time: ~100 μs (for fast RDS applications)
Key Specs:
- VCO center frequency: Approximately 2.7 GHz
- PLL frequency step: 5 kHz (FM), 500 Hz (AM)
- PIN diode driver current: up to 15 mA
- AM LNA maximum gain: 26 dB (with 470 ohm external resistor)
- IFADC sampling frequency: 36.48 MHz
- Audio DAC dynamic range: >100 dB
Features:
- FM, AM and weather band reception
- Fully integrated VCO for world tuning
- High performance PLL for fast RDS system
- Integrated AM-LNA and PIN diodes
- Automatic self alignment for FM front-end preselection filter and image rejection
- Integrated IF filters with high selectivity, dynamic range and adaptive bandwidth control
- Drift-free Digital-IF signal processing with high performance
- RDS demodulation with group and block synchronization
- High performance stereo decoder with noiseblanker
- Digital interface for HD Radio™ reception with digital audio blending
- Fully programmable DSP core
- I2C bus-controlled
- I2S input/output digital audio interfaces
- Single 5 V supply
Applications:
- Car-radio applications
- HD Radio™ reception
Package:
- LQFP64 (10x10x1.4mm)
TDA7706 Features
- ■ FM, AM and weather band reception
- ■ Fully integrated VCO for world tuning
- ■ High performance PLL for fast RDS system
- ■ Integrated AM-LNA and PIN diodes
- ■ Automatic self alignment for FM front-end preselection filter and image rejection
- ■ Integrated IF filters with high selectivity, dynamic range and adaptive bandwidth control
- ■ Drift-free Digital-IF signal processing with high performance
- ■ RDS demodulation with group and block synchronization
- ■ High performance stereo decoder with noiseblanker
- ■ Digital interface for HD Radio™ reception with digital audio blending
- ■ Fully programmable DSP core
- ■ I 2 C bus-controlled
- ■ I 2 S input/output digital audio interfaces
- ■ Single 5 V supply
- ■ LQFP64 package
TDA7706 Pin Configuration
Figure 2. Pin connection (top view)
Table 2. Pin description
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 1 | FMPINDRV | Out | FM | FM PIN diode driver output | |
| 2 | FMPINDdec | In | FM | Integrated FM PINdiode decoupling | '!0'03 |
| 3 | FMMIXdec | - | FM | FM RF signal ground | |
| 4 | FMMIXin2 | In | FM | FM mixer input 2 | |
| 5 | FMMIXin1 | In | FM | FM mixer input 1 | '!0'03 |
| 6 | GNDRF | - | - | RF power ground | - |
Table 2. Pin description
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 7 | TCAM | - | - | AM AGC time constant | '!0'03 |
| 8 | VCCRF | In | - | RF 5V supply | - |
| 9 | CK_SEL | In | - | Master/Slave clock operation select | '!0'03 |
| 10 | GNDVCO | - | VCO | VCO ground | - |
| 11 | LFref | - | VCO | Loop filter reference | - |
| 12 | LF1 | - | VCO | Loop filter output | - |
| 13 | VCCVCO | In | VCO | VCO 5V supply | - |
| 14 | TCAM2 | - | VCO | AM AGC 2 nd order time constant | '!0'03 |
| 15 | PINDdec | - | AM pin diode | AM AGC internal PIN diode decoupling | |
| 16 | PINDin | - | AM pin diode | AM AGC internal PIN diode input | |
| 17 | GNDLNA | - | AM LNA | AM LNA ground | - |
| 18 | LNAin | In | AM LNA | AM LNA input | |
| 19 | LNAdec | - | AM LNA | AM LNA decoupling | |
| 20 | LNAout | Out | AM LNA | AM LNA output | - |
| 21 | LNAin2 | - | AM LNA | AM LNA input 2 nd stage | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 22 | LNAout2 | - | AM LNA | AM LNA output 2 nd stage | |
| 23 | LNAdec2 | - | AM LNA | AM LNA decoupling 2 nd stage | |
| 24 | AMMIXin1 | In | AM mixer inputs | AM mixer input 1 | '!0'03 |
| 25 | AMMIXin2 | In | AM mixer inputs | AM mixer input 2 | '!0'03 |
| 26 | GNDSLINK | - | Supply, ground and reset | Internal inter-IC communication bus ground | - |
| 27 | Vdig | In | Supply, ground and reset | Front-end digital 5 V supply | - |
| 28 | VCCreg1V2 | In | Supply, ground and reset | Internal 1.2 V regulator 5 V supply | - |
| 29 | REG1V2 | Out | Supply, ground and reset | Internal 1.2 V regulator output | |
| 30 | Vreg3v3 | Out | Supply, ground and reset | Internal 3.3 V regulator output | |
| 31 | RSTN | In | Supply, ground and reset | Reset (low active) Pull-up 50 k to 3.3 V IO supply | |
| 32 | RDSint | Out | Supply, ground and reset | RDS interrupt output Pull-down 50 k to ground | - |
| 33 | I2CSDA | In/Out | I 2 C interface | I 2 C bus data Pull-up 50 k to 3.3 V IO supply | |
| 34 | I2CSCL | In | I 2 C interface | I 2 C bus clock Pull-up 50 k to 3.3 V IO supply | |
| 35 | VDD3V3 | In | - | IO ring (3.3V) supply | - |
| 36 | GND3V3 | - | - | IO ring (3.3V) supply | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 37 | GPIO8 In/Out | HD Radio connectivity/ Audio output I2S interface | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | '!0'03 | |
| 38 | GPIO7 | In/Out | Audio SAI word-select Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | |
| 39 | In/Out | Audio SAI data-output Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO6 | |
| 40 | In/Out | Audio SAI data-input Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO5 | |
| 41 | In/Out | SAI Base-Band clock Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO4 | |
| 42 | In/Out | SAI Base-Band word-select Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO3 | |
| 43 | Out | SAI Base-Band I data Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO2 | |
| 44 | Out | SAI Base-Band Q data Pull-down 50 k to ground, SINE_3V3_LIN pad | SAI clk Pull-down 50 k to ground, SINE_3V3_LIN pad | GPIO1 | |
| 45 | In | HD blend Pull-down 50 k to ground | GPIO0 | ||
| 46 | GND1V2 - | - | DSP core ground | - | |
| 47 | VDD core 1V2 | In - | DSP core 1.2V supply | - | |
| 48 | Test | In - | Test Mode Pull-down 50 k to ground | ||
| 49 | VDDPLL1V2 | In | - | Digital PLL 1.2 V supply | - |
| 50 | VDDIO1V2 | In | - | Internal inter-IC communication 1.2V supply | - |
| 51 | VCC-REF | In | - | Front-end reference frequency and regulator 5 V supply | - |
Table 2. Pin description (continued)
Table 2. Pin description (continued)
| Pin | Pin name | I/O | Function | Description | Equivalent circuit |
|---|---|---|---|---|---|
| 52 | OSCin | In | Oscillator | Crystal oscilllator input | - |
| 53 | OSCout | Out | Oscillator | Crsystal oscillator output | |
| 54 | GND-REF | - | - | Front-end reference frequency and regulator ground | - |
| 55 | Vrefdec | - | - | 3.3 V Bias generation decoupling | |
| 56 | GND-ADC_DAC | - | DAC | IFADC and audio DAC ground | - |
| 57 | DACoutL | Out | DAC | Audio output left | |
| 58 | DACoutR | Out | DAC | Audio output right | |
| 59 | VCC-ADC_DAC | In | DAC | IFADC and audio DAC 5V supply | - |
| 60 | VCC-PLL | In | PLL | Tuning PLL 5V supply | - |
| 61 | GND-PLL | - | PLL | Tuning PLL ground | - |
| 62 | PLLtest | Out | PLL | PLL Test output | |
| 63 | TCFM | - | - | FM AGC time constant | |
| 64 | TVDAC | Out | - | Tuning voltage output | - |
Table 2. Pin description (continued)
TDA7706 Typical Application
Figure 6. FM wide-band application
TDA7706 Package Information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com .
ECOPACK ® is an ST trademark.
| $)- | MM | MM | MM | INCH | INCH | INCH |
|---|---|---|---|---|---|---|
| $)- | -). | 490 | -!8 | -). | 490 | -!8 |
| ! | ||||||
| ! | ||||||
| ! | ||||||
| " | ||||||
| # | ||||||
| $ | ||||||
| $ | ||||||
| $ | ||||||
| E | ||||||
| % | ||||||
| % | ||||||
| % | ||||||
| , | ||||||
| , | ||||||
| + | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ | PLQ ← PLQ PD[ |
| CCC |
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| TDA7706CB | STMicroelectronics | — |
Other RF / Wireless
- ST25DV04KC-IE6S3 – STMicroelectronics, Dynamic NFC/RFID Tag IC
- SX1276 – Semtech, Low Power Long Range Transceiver
- XA2214-S14 – Xinluda Information Technology Co., Ltd, GaAs MMIC SPDT Switch
- CC1101 – Texas Instruments, RF Transceiver
- EG915UEUAC-N05-SNNSA – Quectel, LTE Cat 1 Cellular Module
- ESP32-S3 – Espressif Systems, Wireless SoC
- SMTSO2515CTJ – Sinhoo, Surface Mount Nut
- ESP32-WROOM-32 – Espressif Systems, Wi-Fi+BT+BLE MCU module
All RF / Wireless datasheetsAll STMicroelectronics datasheets (808)
Ask your AI agent about the TDA7706
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the TDA7706 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.