R5F11BBX

Part: R5F11BBCAFP — Renesas Electronics (RL78F family)

Type: 16-bit RL78 MCU (CISC core, 32 KB code flash)

Description: 1.6–5.5 V, 32 MHz RL78 MCU with 32 KB code flash, 4 KB data flash and 5.5 KB RAM, in a 32-pin LQFP, with consumption as low as 66 μA/MHz.

Operating Conditions:

• Supply voltage: 1.6–5.5 V
• Operating temperature: -40 to +85 °C (A grade, which includes this part)
• Max CPU clock: 32 MHz
• High-speed on-chip oscillator: 1 to 64 MHz selectable, ±1.0% (VDD = 1.8–5.5 V, TA = -20 to +85 °C)

Absolute Maximum Ratings:

• Supply voltage (VDD, EVDD0): -0.5 to +6.5 V
• Input voltage, P60 to P63 (N-ch open-drain): -0.3 to +6.5 V
• Output current, high (per pin, P00–P06, P10–P17, etc.): -40 mA
• Output current, low (per pin, same pins): 40 mA
• Storage temperature: -65 to +150 °C

Key Specs:

• Code flash: 32 KB (1 KB blocks); data flash: 4 KB; RAM: 5.5 KB
• Minimum instruction time: 0.03125 μs at 32 MHz
• Data flash endurance: 1,000,000 rewrites (typ.), rewrite voltage VDD = 1.8–5.5 V
• A/D converter: 8/10-bit, VDD = 1.6–5.5 V, internal 1.45 V reference and temperature sensor
• D/A converter: 8-bit, 1 or 2 channels
• Serial interfaces: simplified SPI (CSI) 3 to 6 channels, UART 3 channels, I2C/simplified I2C 3 to 6 channels, IrDA 1 channel
• Timers: 9 16-bit channels, 12-bit interval timer, RTC, watchdog
• LVD: 14 selectable levels

Features:

• RL78 CPU core with 3-stage pipeline and multiply/divide/MAC instructions
• HALT, STOP and SNOOZE low-power modes
• On-chip POR and voltage detector
• Data transfer controller (DTC) and event link controller (ELC)
• 2 comparators and a programmable gain amplifier
• Self-programming with boot swap and flash shield window; on-chip debug
• Different-potential interface for 1.8/2.5/3 V devices
• BCD correction circuit

Applications:

• General-purpose applications
• Consumer applications (A grade)

Package:

• 32-pin plastic LQFP (7 × 7 mm, 0.8 mm pitch), PLQP0032GB-A / PLQP0032GE-A

This chapter describes the following electrical specifications.

Target products A: Consumer applications TA = -40 to +85°C

R5F11BxxAxx

• G: Industrial applications when TA = -40 to +105°C products is used in the range of TA = -40 to +85°C R5F11BxxGxx
• Caution 1. The RL78 microcontrollers have an on-chip debug function, which is provided for development and evaluation. Do not use the on-chip debug function in products designated for mass production, because the guaranteed number of rewritable times of the flash memory may be exceeded when this function is used, and product reliability therefore cannot be guaranteed. Renesas Electronics is not liable for problems occurring when the on-chip debug function is used.
• Caution 2. With products not provided with an EVDD0, EVSS0 pin, replace EVDD0 with VDD, or replace EVSS0 with VSS.
• Caution 3. The pins mounted depend on the product. Refer to 2.1 Port Functions to 2.2.1 Functions for each product in the RL78F User's Manual.

(1/2)

Note 1. Connect the REGC pin to VSS via a capacitor (0.47 to 1 μ F). This value regulates the absolute maximum rating of the REGC pin. Do not use this pin with voltage applied to it.

Note 2. Must be 6.5 V or lower.

Note 3. Do not exceed AVREF (+) + 0.3 V in case of A/D conversion target pin.

Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded.

Remark 1. Unless specified otherwise, the characteristics of alternate-function pins are the same as those of the port pins.

Remark 2. AVREF (+): + side reference voltage of the A/D converter.

Remark 3. VSS: Reference voltage

(2/2)

Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded.

Remark Unless specified otherwise, the characteristics of alternate-function pins are the same as those of the port pins.