CP2102N-A02

Part: CP2102N-A02-GQFN28 — Silicon Labs

Type: USB 2.0 Full-Speed to UART Bridge Controller

Description: Single-chip USB-to-UART bridge with an integrated USB transceiver, oscillator and 3.3 V regulator. It supports baud rates from 300 baud to 3 Mbaud and draws 9.5 mA typical in normal operation at 115200 baud.

Operating Conditions:

• Supply voltage: VDD 3.0–3.6 V; VREGIN 3.0–5.25 V; VIO 1.71 V to VDD
• Operating temperature: -40 to +85 °C
• UART baud rates: 300 baud to 3 Mbaud

Absolute Maximum Ratings:

• Max supply voltage: VDD 4.2 V; VREGIN 5.8 V
• Max current sunk into supply pin (IVDD): 400 mA
• Max current sourced or sunk by any UART/GPIO pin: ±100 mA
• Max operating junction temperature: 105 °C
• Storage temperature: -65 to 150 °C

Key Specs:

• Normal operation supply current: 9.5 mA typ (115200 baud, continuous bidirectional data); 13.7 mA typ (3 Mbaud)
• USB suspend current: 195 μA typ
• Current while held in reset: 1.3 mA typ
• USB pull-up current: 200 μA typ, 230 μA max
• VDD supply monitor threshold: 1.95 V min, 2.05 V typ, 2.15 V max
• POR threshold (rising VDD): 1.2 V typ
• Reset delay from POR: 3 ms min, 10 ms typ, 31 ms max
• GPIOs: 7 on the QFN28 device

Features:

• USB 2.0 full-speed (12 Mbps) function controller with integrated transceiver; no external resistors required
• Integrated clock; no external crystal required
• On-chip 3.3 V voltage regulator and power-on reset circuit
• USB Battery Charger Detection (USB BCS 1.2)
• Remote wakeup for waking a suspended host
• UART with full handshaking and modem signals; 5–8 data bits, 1/1.5/2 stop bits, odd/even/mark/space/no parity
• 512-byte receive buffer and 512-byte transmit buffer
• Hardware or Xon/Xoff handshaking
• 960-byte programmable ROM for vendor ID, product ID, serial number and descriptor strings
• Royalty-free Virtual COM port drivers for Windows, Mac and Linux
• GUI-based configurator
• Pin compatible with CP2101/2/9 (QFN28)

Applications:

• POS terminals
• USB dongles
• Gaming controllers
• Medical equipment
• Data loggers

Package:

• QFN28 (CP2102N-A02-GQFN28, Pb-free/RoHS compliant)

• No firmware development required
• Simple GUI-based configurator
• Integrated USB transceiver; no external resistors required
• Integrated clock; no external crystal required
• USB 2.0 full-speed compatible
• Data transfer rates up to 3 Mbaud
• USB Battery Charger Detection (USB BCS 1.2 Specification)
• Remote wakeup for waking a suspended host
• Low operating current : 9.5 mA
• Royalty-free Virtual COM port drivers
• Medical equipment
• Data loggers

All electrical parameters in all tables are specified under the conditions listed in Table 3.1 Recommended Operating Conditions on page 10, unless stated otherwise.

Stresses above those listed in 3.3 Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. For more information on the available quality and reliability data, see the Quality and Reliability Monitor Report at http://www.silabs.com/support/quality/pages/ default.aspx.

Table 3.10. Absolute Maximum Ratings

1. Exposure to maximum rating conditions for extended periods may affect device reliability.

2. On devices without a VIO pin, V IO = V DD

Table 3.1. Recommended Operating Conditions

1. Standard USB compliance tests require 3.0 V on VDD for compliant operation.
2. All voltages with respect to GND.
3. On devices without a VIO pin, V IO = V DD .
4. GPIO levels are undefined whenever VIO is less than 1 V.

Table 3.9. Thermal Conditions

1. Thermal resistance assumes a multi-layer PCB with any exposed pad soldered to a PCB pad.

Figure 6.1. QFN28 Package Drawing

Table 6.1. QFN28 Package Dimensions

1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC outline MO-220 except for custom features D2, E2, L, Z, and Y which are toleranced per supplier designation.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.