ATMEGA168A-AUR

Part: ATmega168PA — Microchip Technology (formerly Atmel)

Type: 8-bit Microcontroller

Description: Low power, CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture, featuring 16 KB In-System Self-Programmable Flash, 512 Bytes EEPROM, 1 KB Internal SRAM, and up to 20 MIPS throughput at 20 MHz.

Operating Conditions:

• Supply voltage: 1.8–5.5V
• Operating temperature: -40°C to 85°C
• Max clock frequency: 20 MHz @ 4.5–5.5V

Absolute Maximum Ratings:

Key Specs:

• CPU Throughput: Up to 20 MIPS at 20MHz
• Flash Program Memory: 16 KBytes
• EEPROM: 512 Bytes
• Internal SRAM: 1 KByte
• Flash Write/Erase Cycles: 10,000
• EEPROM Write/Erase Cycles: 100,000
• Active Mode Power Consumption: 0.2mA (at 1MHz, 1.8V, 25°C)
• Power-down Mode Power Consumption: 0.1μA (at 1MHz, 1.8V, 25°C)

Features:

• 131 Powerful Instructions - Most Single Clock Cycle Execution
• 32 x 8 General Purpose Working Registers
• On-chip 2-cycle Multiplier
• QTouch library support for capacitive touch
• Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
• One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode
• Real Time Counter with Separate Oscillator
• Six PWM Channels
• 8-channel 10-bit ADC (TQFP and VQFN package) / 6-channel 10-bit ADC (SPDIP Package)
• Programmable Serial USART
• Master/Slave SPI Serial Interface
• Byte-oriented 2-wire Serial Interface (Philips I2C compatible)
• Programmable Watchdog Timer with Separate On-chip Oscillator
• On-chip Analog Comparator
• Interrupt and Wake-up on Pin Change
• Power-on Reset and Programmable Brown-out Detection
• Internal Calibrated Oscillator
• Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby
• 23 Programmable I/O Lines

Applications:

Package:

• 28-pin SPDIP
• 32-lead TQFP
• 28-pad VQFN
• 32-pad VQFN

• ® 8-Bit Microcontroller Family
• Advanced RISC Architecture

̶

• 131 Powerful Instructions - Most Single Clock Cycle Execution

̶

• 32 x 8 General Purpose Working Registers
• Up to 20 MIPS Throughput at 20MHz

̶

• On-chip 2-cycle Multiplier

̶

• High Endurance Non-volatile Memory Segments

̶

• 4/8/16/32KBytes of In-System Self-Programmable Flash program memory

̶

• 256/512/512/1KBytes EEPROM
• 512/1K/1K/2KBytes Internal SRAM
• Write/Erase Cycles: 10,000 Flash/100,000 EEPROM
• Data retention: 20 years at 85°C/100 years at 25°C (1)
• Optional Boot Code Section with Independent Lock Bits
• In-System Programming by On-chip Boot Program
• True Read-While-Write Operation
• Programming Lock for Software Security

̶

• QTouch ® library support

̶

• Capacitive touch buttons, sliders and wheels

̶

• QTouch and QMatrix™ acquisition

̶

• Up to 64 sense channels
• Peripheral Features

̶

• Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

̶

• One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode

̶

̶

̶

̶

̶

Figure 1-1. Pinout ATmega48A/PA/88A/PA/168A/PA/328/P

Table 29-1. ATmega48A DC characteristics - T A = -40 C to 85 C, V CC = 1.8V to 5.5V (unless otherwise noted)

Notes:

1. Values with 'Minimizing Power Consumption' enabled (0xFF).

2. Typical values at 25 C.

3. The current consumption values include input leakage current.

*NOTICE:

Stresses beyond those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.