NCP164ASN180
LDO RegulatorThe NCP164ASN180 is a ldo regulator from onsemi. View the full NCP164ASN180 datasheet below including key specifications, absolute maximum ratings.
NCP164ASN180 shares its datasheet with NCP164AMT120, whose page lists every part number it covers.
Official NCP164ASN180 datasheet (PDF) — the source this page was extracted from.
NCP164ASN180 Key Specifications
| Parameter | Value |
|---|---|
| Packaging | MouseReel |
| Standard Pack Qty | 3000 |
| PSRR | 85 dB typ at 1 kHz, 10 mA |
| Output Noise | 9 µVRMS (10 Hz to 100 kHz, fixed version) |
| Output Capacitor | 1 µF ceramic |
| Shutdown Current | 0.01 µA typ, 1.5 µA max |
| Thermal Shutdown | 165 °C, 15 °C hysteresis |
| Quiescent Current | 30 µA typ, 40 µA max |
| Package Dimensions | TSOP-5 3 mm x 1.5 mm x 1 mm |
| Input Voltage Range | 1.6V to 5.5V |
| Output Current Limit | 350 mA min, 560 mA typ |
| Power Good Thresholds | 95% rising, 90% falling |
| Maximum Output Current | 300 mA |
| Active Output Discharge | 260 Ω (Version A) |
| Output Voltage Accuracy | ±2% over load and temperature |
| Junction Temperature Range | -40°C to 150°C |
| Output Voltage (This Variant) | 1.8V fixed |
| Dropout Voltage (1.8 V, 300 MA) | 155 mV typ, 255 mV max |
NCP164ASN180 Overview
Part: NCP164AMT120TAG — onsemi
Type: Low Dropout (LDO) Linear Regulator with Power Good
Description: 300 mA LDO with 1.6–5.5 V input, 1.2 V fixed output (±2% accuracy), 30 μA typical quiescent current, 85 dB PSRR at 1 kHz and 9 μVRMS output noise, in a WDFN6 2x2 package.
Operating Conditions:
- Supply voltage: 1.6–5.5 V
- Operating junction temperature: -40 to 150 °C (electrical characteristics specified over this range)
- Output current: up to 300 mA
- Output capacitor: 1 μF or greater ceramic, input capacitor at least 1 μF
Absolute Maximum Ratings:
- Input voltage (VIN): -0.3 to 6 V
- Output voltage (VOUT): -0.3 to VIN + 0.3 V, max 6 V
- Chip enable voltage (VCE): -0.3 to 6 V
- Power Good voltage: -0.3 to 6 V
- Power Good current: 30 mA
- Maximum junction temperature: 150 °C
- Storage temperature: -55 to 150 °C
- ESD: HBM 2000 V, CDM 1000 V
Key Specs:
- Output voltage accuracy: ±2% (VIN = VOUT(NOM) + 0.5 V to 5.0 V, 0.1 mA ≤ IOUT ≤ 300 mA)
- Dropout voltage: 170 mV typ, 295 mV max at 300 mA for 1.5 V output; 110 mV typ for 3.3 V output
- Quiescent current: 30 μA typ, 40 μA max (IOUT = 0 mA)
- Shutdown current: 0.01 μA typ, 1.5 μA max (VEN ≤ 0.4 V)
- Current limit: 350 mA min, 560 mA typ (VOUT = 90% of nominal); short-circuit current 580 mA typ
- PSRR (VOUT = 3.3 V, IOUT = 10 mA): 83 dB at 100 Hz, 85 dB at 1 kHz, 80 dB at 10 kHz, 61 dB at 100 kHz
- Output noise: 9 μVRMS (10 Hz–100 kHz, IOUT = 10 mA)
- Turn-on time: 120 μs typ (COUT = 1 μF)
- Power Good thresholds: 95% rising, 90% falling; PG low voltage 0.3 V max at 5 mA
- Thermal shutdown: 165 °C typ, 15 °C hysteresis
- Thermal resistance WDFN6: RθJA 51 °C/W
Features:
- Fixed output options from 1.2 V to 5 V, plus adjustable version with 1.1 V reference
- Ultra-low noise and ultra-high PSRR
- Open-collector Power Good output
- Enable pin (EN threshold: 0.7 V high, 0.2 V low)
- Active output discharge (version A)
- Current limiting, soft-start and thermal protection
- Stable with small 1 μF ceramic capacitors
- Pb-free, halogen-free/BFR-free, RoHS compliant
Applications:
- Communication systems
- Telematics, infotainment and clusters
- In-vehicle networking
- General-purpose automotive
Package:
- WDFN6 2 mm x 2 mm x 0.75 mm, 0.65 mm pitch (Case 511BR), non-wettable flanks, 3000 / tape and reel
- Other family option: TSOP-5 (Case 483)
NCP164ASN180 Features
- Operating Input Voltage Range: 1.6 V to 5.5 V
- Available in Fixed Voltage Option: 1.2 V to 5 V
- 2% Accuracy Over Load and Temperature
- Adjustable Version Reference Voltage: 1.1 V
- Ultra Low Quiescent Current Typ. 30 m A
- Very Low Dropout: 110 mV at 300 mA for 3.3 V Variant
- Standby Current: Typ. 0.1 m A
- Ultra High PSRR: Typ. 85 dB at 10 mA, f = 1 kHz
- Stable with a 1 m F Small Case Size Ceramic Capacitors
- Ultra Low Noise: 9 m VRMS (Fixed Version)
- Available in - TSOP -5 3 mm x 1.5 mm x 1 mm CASE 483
- WDFN6 2 mm x 2 mm x 0.75 mm CASE 511BR
- These Devices are Pb -Free, Halogen Free/BFR Free and are RoHS Compliant
NCP164ASN180 Applications
- Communication Systems
- Telematics, Infotainment and Clusters
- In -Vehicle Networking
- General Purpose Automotive
Figure 1. Typical Application Schematic
TSOP -5 CASE 483
WDFN6 2x2, 0.65P CASE 511BR
NCP164ASN180 Absolute Maximum Ratings
| Rating | Symbol | Value | Unit |
|---|---|---|---|
| Input Voltage (Note 1) | V IN | - 0.3 to 6 | V |
| Output Voltage | V OUT | - 0.3 to V IN +0.3, max. 6 | V |
| Chip Enable Input | V CE | - 0.3 to 6 | V |
| Power Good Voltage | V PG | - 0.3 to 6 | V |
| Power Good Current | I PG | 30 | mA |
| Output Short Circuit Duration | t SC | unlimited | s |
| Maximum Junction Temperature | T J | 150 | C |
| Storage Temperature | T STG | - 55 to 150 | C |
| ESD Capability, Human Body Model (Note 2) | ESD HBM | 2000 | V |
| ESD Capability, Charged Device Model (Note 2) | ESD CDM | 1000 | V |
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected.
-
Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area.
-
This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per AEC -Q100 -002 (EIA/JESD22 -A114) ESD Charged Device Model tested per EIA/JESD22 -C101, Field Induced Charge Model
NCP164ASN180 Thermal Information
| Rating | Symbol | Value | Unit |
|---|---|---|---|
| THERMAL CHARACTERISTICS, TSOP - 5 PACKAGE | |||
| Thermal Resistance, Junction - to - Ambient (Note 3) | R q JA | 158 | C/W |
| Thermal Resistance, Junction - to - Case (top) | R q JC(top) | 155 | C/W |
| Thermal Resistance, Junction - to - Case (bottom) (Note 4) | R q JC(bot) | 102 | C/W |
| Thermal Resistance, Junction - to - Board | R q JB | 197 | C/W |
| Characterization Parameter, Junction - to - Top | Y JT | 40 | C/W |
| Characterization Parameter, Junction - to - Board | Y JB | 82 | C/W |
| THERMAL CHARACTERISTICS, WDFN6 - 2X2, 0.65 PITCH PACKAGE | |||
| Thermal Resistance, Junction - to - Ambient (Note 3) | R q JA | 51 | C/W |
| Thermal Resistance, Junction - to - Case (top) | R q JC(top) | 142 | C/W |
| Thermal Resistance, Junction - to - Case (bottom) (Note 4) | R q JC(bot) | 2.0 | C/W |
| Thermal Resistance, Junction - to - Board | R q JB | 117 | C/W |
| Characterization Parameter, Junction - to - Top | Y JT | 1.9 | C/W |
| Characterization Parameter, Junction - to - Board | Y JB | 7.7 | C/W |
Table 4. ELECTRICAL CHARACTERISTICS ( -40 C T J 150 C; V IN = V OUT(NOM) + 0.5 V; I OUT = 1 mA, C IN = C OUT = 1 m F, V EN = V IN , unless otherwise noted. Typical values are at T J = +25 C (Note 5))
| Parameter | Test Conditions | Test Conditions | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|---|
| Operating Input Voltage | V IN | 1.6 | 5.5 | V | |||
| Output Voltage Accuracy | V IN = V OUT(NOM) + 0.5 V to 5.0 V, 0.1 mA I OUT 300 mA | V IN = V OUT(NOM) + 0.5 V to 5.0 V, 0.1 mA I OUT 300 mA | V OUT | - 2 | +2 | % | |
| Reference Voltage (Adjustable Ver. ADJ pin connected to OUT) | V IN = 1.6 V to 5.0 V, 0.1 mA I OUT 300 mA | V IN = 1.6 V to 5.0 V, 0.1 mA I OUT 300 mA | V ADJ | 1.078 | 1.1 | 1.122 | V |
| Line Regulation | V OUT(NOM) + 0.5 V V IN 5.0 V | V OUT(NOM) + 0.5 V V IN 5.0 V | Line Reg | 0.5 | mV/V | ||
| Load Regulation | I OUT = 1 mA to 300 mA | I OUT = 1 mA to 300 mA | Load Reg | 2 | mV | ||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | I OUT = 300 mA | V OUT(NOM) = 1.5 V | V DO | 170 | 295 | mV | |
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 1.8 V | 155 | 255 | ||||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 2.5 V | 125 | 200 | ||||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 2.8 V | 115 | 185 | ||||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 3.0 V | 113 | 177 | ||||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 3.3 V | 110 | 170 | ||||
| Dropout Voltage (Note 6) TSOP - 5, WDFN6 | V OUT(NOM) = 4.5 V | 95 | 135 | ||||
| Output Current Limit | V OUT = 90% V OUT(NOM) | V OUT = 90% V OUT(NOM) | I CL | 350 | 560 | mA | |
| Short Circuit Current | V OUT = 0 V | V OUT = 0 V | I SC | 580 | |||
| Quiescent Current | I OUT = 0 mA | I OUT = 0 mA | I Q | 30 | 40 | m A | |
| Shutdown Current | V EN 0.4 V | V EN 0.4 V | I DIS | 0.01 | 1.5 | m A | |
| EN Pin Threshold Voltage | EN Input Voltage 'H' | EN Input Voltage 'H' | V ENH | 0.7 | V | ||
| EN Input Voltage 'L' | EN Input Voltage 'L' | V ENL | 0.2 | ||||
| EN Pull Down Current | V EN = 5.0 V | V EN = 5.0 V | I EN | 0.2 | 0.6 | m A | |
| Power Good Threshold Voltage | Output Voltage Raising | Output Voltage Raising | V PGUP | 95 | % | ||
| Output Voltage Falling | Output Voltage Falling | V PGDW | 90 | ||||
| Power Good Output Voltage Low | I PG = 5 mA, Open drain | I PG = 5 mA, Open drain | V PGLO | 0.3 | V | ||
| Turn - On Time (Note 7) | C OUT = 1 m F , From assertion of V EN to V OUT = 95% V OUT(NOM) | C OUT = 1 m F , From assertion of V EN to V OUT = 95% V OUT(NOM) | 120 | m s | |||
| Power Supply Rejection Ratio (Note 7) | V OUT(NOM) = 3.3 V , I = 10 mA | f = 100 Hz | P SRR | 83 | dB | ||
| Power Supply Rejection Ratio (Note 7) | OUT | f = 1 kHz | 85 | ||||
| Power Supply Rejection Ratio (Note 7) | f = 10 kHz | 80 | |||||
| Power Supply Rejection Ratio (Note 7) | f = 100 kHz | 61 | |||||
| Output Voltage Noise (Fixed Ver.) | f = 10 Hz to 100 kHz | I OUT = 10 mA | V N | 9 | m V RMS | ||
| Thermal Shutdown Threshold | Temperature rising | Temperature rising | T SDH | 165 | C | ||
| (Note 7) | Temperature hysteresis | Temperature hysteresis | T HYST | 15 | C | ||
| Active output discharge resistance | V EN < 0.2 V, Version A only | V EN < 0.2 V, Version A only | R DIS | 260 | W |
NCP164ASN180 Typical Application
- Communication Systems
- Telematics, Infotainment and Clusters
- In -Vehicle Networking
- General Purpose Automotive
Figure 1. Typical Application Schematic
TSOP -5 CASE 483
WDFN6 2x2, 0.65P CASE 511BR
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| NCP164 | onsemi | — |
| NCP164AMT120 | onsemi | WDFN6 2x2mm |
| NCP164AMT120TAG | onsemi | TSOP-5 (3 mm x 1.5 mm |
| NCP164AMT180 | onsemi | WDFN-6 2x2mm |
| NCP164AMT280 | onsemi | WDFN-6 2x2mm |
| NCP164AMT330 | onsemi | WDFN6 2x2mm |
| NCP164AMTADJ | onsemi | WDFN6 2x2mm |
| NCP164ASN280 | onsemi | TSOP-5 |
| NCP164ASN330 | onsemi | TSOP-5 |
| NCP164ASNADJ | onsemi | TSOP-5 |
Other Linear Regulators (LDO)
- LP5907MFX-3.3/NOPB – Texas Instruments, Low-Noise, Low-IQ LDO
- AP7343D-30FS4-7B – Diodes Incorporated, 300mA High PSRR Low-Noise LDO
- MC78M12ACDTRKG – onsemi, Positive Voltage Regulator
- LM317 – Texas Instruments, Adjustable Regulator
- ME6211C33M5G-N – Nanjing Micro One, High PSRR Low-Noise CMOS LDO Regulator
- AAT3221IGV-3.3-T1 – Skyworks Solutions, LDO Linear Regulator
- AMS1117 – Advanced Monolithic Systems, Low Dropout Voltage Regulator
- AMS1117-1.2 – EVVO, Low Dropout Regulator
All Linear Regulators (LDO) datasheetsAll onsemi datasheets (337)
Ask your AI agent about the NCP164ASN180
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the NCP164ASN180 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.