MX25L6473E

Serial Multi I/O Flash Memory

The MX25L6473E is a serial multi i/o flash memory from Macronix. View the full MX25L6473E datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

MX25L6473E shares its datasheet with MX25L6473EZNI-10G, whose page lists every part number it covers.

Official MX25L6473E datasheet (PDF) — the source this page was extracted from.

Manufacturer

Macronix

MX25L6473E Key Specifications

Parameter	Value
Interface	SPI (Single/Dual/Quad I/O, MXSMIO)
Page Size	256 bytes
Erase Sizes	4KB sector, 32KB block, 64KB block, chip erase
Secured OTP	4K-bit
Memory Density	64 Mbit (8,388,608 x 8)
Supply Voltage	3V
Manufacturer ID	C2h
Max Clock Frequency	104 MHz
Quad Enable (QE) Bit	Permanently fixed QE=1 (4 I/O mode enabled)
Operating Temperature	-40°C to 85°C
Available Packages (Family)	16-SOP 300mil, 8-SOP 200mil, 8-VSOP 200mil, 8-WSON 6x5mm, 12-ball WLCSP

MX25L6473E Overview

Part: MX25L6473EZNI-10G

Type: Serial Multi I/O Flash Memory

Description: 64M-bit Serial Multi I/O Flash Memory with 2.7–3.6V operation, supporting Single, Dual, and Quad I/O modes, and up to 104MHz read speed.

Operating Conditions:

Supply voltage: 2.7 to 3.6 V
Max clock frequency: Up to 104MHz (4 I/O read)

Key Specs:

Memory size: 64M-bit (8,388,608 x 8 bits)
Fast read speed (1 I/O): 104MHz with 8 dummy cycles
Fast read speed (2 I/O): 86MHz with 4 dummy cycles
Fast read speed (4 I/O): Up to 104MHz
Page program time: 0.7ms (typ.), 3ms (max.) per 256-byte page
Sector erase time: 30ms (typ.) per 4K-byte sector
Block erase time: 0.25s (typ.) per 64K-byte block
Active read current: 19mA (max.) at 104MHz
Standby current: 15μA (typ.)
Deep power down current: 1μA (typ.)
Erase/program cycles: 100,000 (Typical)
Data retention: 20 years

Features:

Multi I/O Support - Single I/O, Dual I/O and Quad I/O
Auto Erase and Auto Program Algorithms
Continuous Program mode
Permanently fixed QE bit, QE=1; and 4 I/O mode is enabled
Supports Serial Peripheral Interface -- Mode 0 and Mode 3
2048 Equal Sectors with 4K bytes each
128 Equal Blocks with 64K bytes each
Latch-up protected to 100mA from -1V to Vcc +1V
Advanced Security Features: BP0-BP3 block group protect, Flexible individual block protect, 4K bits secured OTP
Electronic Identification: JEDEC 1-byte Manufacturer ID and 2-byte Device ID, RES, REMS, REMS2, REMS4 commands
Support Serial Flash Discoverable Parameters (SFDP) mode

Package:

16-pin SOP (300mil)
8-pin SOP (200mil)
8-pin VSOP (200mil)
8-WSON (6x5mm)
12-ball WLCSP (Ball Diameter 0.30mm)

MX25L6473E Features

Multi I/O Support - Single I/O, Dual I/O and Quad I/O
Auto Erase and Auto Program Algorithms
Continuous Program mode
Permanently fixed QE bit, QE=1; and 4 I/O mode is enabled

MX25L6473E Pin Configuration

SYMBOL	DESCRIPTION
CS#	Chip Select
SI/SIO0	Serial Data Input (for 1xI/O)/ Serial Data Input & Output (for 2xI/O or 4xI/O mode)
SO/SIO1	Serial Data Output (for 1xI/O)/Serial Data Input & Output (for 2xI/O or 4xI/O mode)
SCLK	Clock Input
SIO2	Serial Data Input & Output (for 4xI/O mode)
SIO3	Serial data Input/Output for 4 x I/O mode
VCC	+ 3.0V Power Supply
GND	Ground
NC	No Connection

Note: SIO2 and SIO3 need to be externally pulled to a high (recommended) or low state when the device is in Standby mode or Deep Power mode.

MX25L6473E Electrical Characteristics

Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V

Symbol	Parameter	Notes	Min.	Typ.	Max.	Units	Test Conditions
ILI	Input Load Current	1			± 2	μA	VCC = VCC Max, VIN = VCC or GND
ILO	Output Leakage Current	1			± 2	μA	VCC = VCC Max, VOUT = VCC or GND
ISB1	VCC Standby Current	1		15	50	μA	VIN = VCC or GND, CS# = VCC
ISB2	Deep Power-down Current			1	25	μA	VIN = VCC or GND, CS# = VCC
ICC1	VCC Read	1			35	mA	f=104MHz (4 x I/O read) SCLK=0.1VCC/0.9VCC, SO=Open
ICC1	VCC Read	1			19	mA	f=104MHz (1 x I/O read) SCLK=0.1VCC/0.9VCC, SO=Open
ICC1	VCC Read	1			25	mA	fQ=86MHz (4 x I/O read) SCLK=0.1VCC/0.9VCC, SO=Open
ICC1	VCC Read	1			20	mA	fT=86MHz (2 x I/O read) SCLK=0.1VCC/0.9VCC, SO=Open
ICC1	VCC Read	1			10	mA	f=33MHz, SCLK=0.1VCC/0.9VCC, SO=Open
ICC2	VCC Program Current (PP)	1		15	25	mA	Program in Progress, CS# = VCC
ICC3	VCC Write Status Register (WRSR) Current			15	20	mA	Program status register in progress, CS#=VCC
ICC4	VCC Sector Erase Current (SE)	1		10	25	mA	Erase in Progress, CS#=VCC
ICC5	VCC Chip Erase Current (CE)	1		15	25	mA	Erase in Progress, CS#=VCC
VIL	Input Low Voltage		-0.5		0.8	V
VIH	Input High Voltage		0.7VCC		VCC+0.4	V
VOL	Output Low Voltage				0.4	V	IOL = 1.6mA
VOH	Output High Voltage		VCC-0.2			V	IOH = -100μA

MX25L6473E Absolute Maximum Ratings

Rating		Value
Ambient Operating Temperature	Industrial grade	-40°C to 85°C
Storage Temperature		-65°C to 150°C
Applied Input Voltage		-0.5V to VCC+0.5V
Applied Output Voltage		-0.5V to VCC+0.5V
VCC to Ground Potential		-0.5V to 4.0V

MX25L6473E Package Information

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part Number	Manufacturer	Package
MX25L6473EZNI-10G	Macronix	16-pin SOP (300mil)

Other Memory ICs

CH347T – WCH, Serial SLC NAND Flash Memory
M24512-DFMC6TG – STMicroelectronics, EEPROM
ST25DV04KC-JF6L3 – STMicroelectronics, Dynamic NFC/RFID Tag IC
ZD25WQ16CTIGT – Zetta, Serial Multi I/O NOR Flash
AT25SL128A-MHE-T – Renesas Electronics, 128-Mbit SPI Serial NOR Flash
23A1024 – Microchip Technology, Serial SRAM
23LC1024 – Microchip Technology, Serial SRAM
23LC1024-I/P – Microchip Technology, Serial SRAM

All Memory ICs datasheets All Macronix datasheets (3)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the MX25L6473E

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the MX25L6473E run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.