DRV8313RHHR
Triple 1/2-H Bridge DriverThe DRV8313RHHR is a triple 1/2-h bridge driver from Texas Instruments. View the full DRV8313RHHR datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
Manufacturer
Texas Instruments
Category
Triple 1/2-H Bridge Driver
Key Specifications
| Parameter | Value |
|---|---|
| Applications | General Purpose |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Interface | Parallel |
| Motor Type (DC) | Brushless DC (BLDC) |
| Mounting Type | Surface Mount |
| Operating Temperature | -40°C ~ 150°C (TJ) |
| Output Configuration | Half Bridge (3) |
| Package / Case | 28-PowerTSSOP (0.173", 4.40mm Width) |
| Supplier Device Package | 28-HTSSOP |
| Diode Technology | Power MOSFET |
| Load Voltage | 8V ~ 60V |
| Supply Voltage | 8V ~ 60V |
Overview
Part: DRV8313 — Texas Instruments
Type: Triple 1/2-H Bridge Driver
Description: The DRV8313 is a triple 1/2-H bridge driver IC with 2.5-A peak current capability, designed for 3-phase brushless DC motors, solenoids, or brushed DC motors, featuring an 8-V to 60-V operating supply voltage range and integrated protection functions.
Operating Conditions:
- Supply voltage: 8–60 V
- Operating ambient temperature: -40 to 125 °C
- Digital pin voltage: 0–5.5 V
- V3P3 load current: 0–10 mA
Absolute Maximum Ratings:
- Max supply voltage: 65 V
- Max junction temperature: 150 °C
- Max storage temperature: 150 °C
Key Specs:
- VM operating supply current: 1 mA (typ, VM = 24 V, f PWM < 50 kHz)
- VM sleep-mode supply current: 500 μA (typ, VM = 24 V)
- V3P3 voltage: 3.1 V (min) to 3.52 V (max)
- High-side FET ON-resistance: 0.24 Ω (typ, VM = 24 V, IO = 1 A, TJ = 25°C)
- Low-side FET ON-resistance: 0.24 Ω (typ, VM = 24 V, IO = 1 A, TJ = 25°C)
- VM undervoltage lockout voltage: 6.3 V (typ, VM rising)
- Overcurrent protection trip level: 3 A (min) to 5 A (typ)
- Thermal shutdown temperature: 150 °C (min) to 180 °C (max)
Features:
- Triple 1/2-H Bridge Driver IC
- High Current-Drive Capability: 2.5-A Peak
- Low MOSFET ON-Resistance
- Independent 1/2-H-Bridge Control
- Uncommitted Comparator Can Be Used for Current Limit or Other Functions
- Built-In 3.3-V 10-mA LDO Regulator
- Sleep Mode for Standby Operation
- Internal protection functions: undervoltage, charge pump faults, overcurrent, short circuits, and overtemperature.
Applications:
- Camera Gimbals
- HVAC Motors
- Office Automation Machines
- Factory Automation and Robotics
Package:
- HTSSOP (28) - 9.70 mm × 4.40 mm
- VQFN (36) - 6.00 mm × 6.00 mm
Features
- 1 · Triple 1/2-H Bridge Driver IC
- -3-Phase brushless DC Motors
- -Solenoid and Brushed DC Motors
- High Current-Drive Capability: 2.5-A Peak
- Low MOSFET ON-Resistance
- Independent 1/2-H-Bridge Control
- Uncommitted Comparator Can Be Used for Current Limit or Other Functions
- Built-In 3.3-V 10-mA LDO Regulator
- 8-V to 60-V Operating Supply-Voltage Range
- Sleep Mode for Standby Operation
- Small Package and Footprint
- -28-Pin HTSSOP (PowerPAD™ Package)
- -36-Pin VQFN
Applications
- Camera Gimbals
- HVAC Motors
- Office Automation Machines
- Factory Automation and Robotics
Pin Configuration
PWP Package 28-Pin HTSSOP With PowerPAD Package Top View
NC - No internal connection
Electrical Characteristics
TA = 25°C, over operating free-air temperature range (unless otherwise noted)
| PARAMETER | PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT |
|---|---|---|---|---|---|---|
| POWER SUPPLIES | POWER SUPPLIES | POWER SUPPLIES | POWER SUPPLIES | POWER SUPPLIES | POWER SUPPLIES | POWER SUPPLIES |
| I VM | VM operating supply current | V M = 24 V, f PWM < 50 kHz | 1 | 5 | mA | |
| I VMQ | VM sleep-mode supply current | V M = 24 V | 500 | 800 | μA | |
| INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) | INTERNAL REGULATOR (V3P3) |
| V 3P3 | V3P3 voltage | I OUT = 0 to 10 mA | 3.1 | 3.3 | 3.52 | V |
| LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) | LOGIC-LEVEL INPUTS (nSLEEP, ENx, INx) |
| V IL | Input low voltage | 0.6 | 0.7 | V | ||
| V IH | Input high voltage | 2.2 | 5.25 | V | ||
| V HYS | Input hysteresis | 50 | 600 | mV | ||
| I IL | Input low current | VIN = 0 | -5 | 5 | μA | |
| I IH | Input high current | VIN = 3.3 V | 100 | μA | ||
| R PD | Pulldown resistance | 100 | k Ω | |||
| OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) | OPEN-DRAIN OUTPUTS (nFAULT and nCOMPO) |
| V OL | Output low voltage | I O = 5 mA | 0.5 | V | ||
| I OH | Output high leakage current | V O = 3.3 V | 1 | μA | ||
| COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) | COMPARATOR (COMPP, COMPN, nCOMPO) |
| V CM | Common-mode input-voltage range | 0 | 5 | V | ||
| V IO | Input offset voltage | -7 | 7 | mV | ||
| I IB | Input bias current | -300 | 300 | nA | ||
| t R | Response time | 100-mV step with 10-mV overdrive | 2 | μs | ||
| H-BRIDGE FETs | H-BRIDGE FETs | H-BRIDGE FETs | H-BRIDGE FETs | H-BRIDGE FETs | H-BRIDGE FETs | H-BRIDGE FETs |
| r DS(on) | High-side FET ON-resistance | V M = 24 V, I O = 1 A, T J = 25°C | 0.24 | Ω | ||
| r DS(on) | V M = 24 V, I O = 1 A, T J = 85°C (1) | 0.29 | 0.39 | Ω | ||
| r DS(on) | Low-side FET ON-resistance | V M = 24 V, I O = 1 A, T J = 25°C | 0.24 | Ω | ||
| r DS(on) | V M = 24 V, I O = 1 A, T J = 85°C (1) | 0.29 | 0.39 | Ω | ||
| I OFF Off-state leakage current | I OFF Off-state leakage current | I OFF Off-state leakage current | -2 | 2 | μA | |
| PROTECTION CIRCUITS | PROTECTION CIRCUITS | PROTECTION CIRCUITS | PROTECTION CIRCUITS | PROTECTION CIRCUITS | PROTECTION CIRCUITS | PROTECTION CIRCUITS |
| V UVLO | VM undervoltage lockout voltage | V M rising | 6.3 | 8 | V | |
| I OCP | Overcurrent protection trip level | 3 | 5 | A | ||
| t OCP | Overcurrent protection deglitch time | 5 | μs | |||
| T TSD (1) | Thermal shutdown temperature | Die temperature | 150 | 160 | 180 | °C |
| T HYS (1) | Thermal shutdown hysteresis | Die temperature | 35 | °C |
Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)(2)
| MIN | MAX | UNIT | |
|---|---|---|---|
| Power-supply voltage (VM) | -0.3 | 65 | V |
| Power supply voltage ramp rate (VM) | 0 | 2 | V/μs |
| Charge pump voltage (VCP, CPH) | -0.3 | VM + 12 | V |
| Charge pump negative switching pin (CPL) | -0.3 | VM | V |
| Internal regulator current output (V3P3) | 0 | 10 | mA |
| Internal regulator voltage (V3P3) | -0.3 | 3.8 | V |
| Control pin voltage (nRESET, nSLEEP, nFAULT, nCOMPO, ENx, INx) | -0.5 | 7 | V |
| Comparator input-voltage (COMPP, COMPN) | -0.5 | 7 | V |
| Open drain output current (nFAULT, nCOMPO) | 0 | 10 | mA |
| Continuous phase node pin voltage (OUTx) | -0.7 | VM + 0.7 | V |
| Continuous 1/2-H-bridge source voltage (PGNDx) | -600 | 600 | mV |
| Peak output current (OUTx) | Internally limited | Internally limited | A |
| Operating junction temperature T J | -40 | 150 | °C |
| Storage temperature T stg | -60 | 150 | °C |
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| VM | Motor power-supply voltage (1) | 8 | 60 | V |
| V IN | Digital pin voltage | 0 | 5.5 | V |
| f PWM | Applied PWM signal on ENx, INx | 0 | 250 | kHz |
| V GNDX | PGNDx pin voltage | -500 | 500 | mV |
| I V3P3 | V3P3 load current | 0 | 10 (2) | mA |
| T A | Operating ambient temperature | -40 | 125 | °C |
Thermal Information
| DRV8313 | DRV8313 | ||
|---|---|---|---|
| THERMAL METRIC | (1) | PWP (HTSSOP) | RHH (VQFN) |
| 28 PINS | 36 PINS | ||
| R θ JA | Junction-to-ambient thermal resistance | 31.6 | 31.1 |
| R θ JC(top) | Junction-to-case (top) thermal resistance | 15.9 | 17.3 |
| R θ JB | Junction-to-board thermal resistance | 5.6 | 5.6 |
| ψ JT | Junction-to-top characterization parameter | 0.2 | 0.2 |
| ψ JB | Junction-to-board characterization parameter | 5.5 | 5.6 |
| R θ JC(bot) | Junction-to-case (bottom) thermal resistance | 1.4 | 1.3 |
Typical Application
The DRV8313 can be used to drive Brushless-DC motors, Brushed-DC motors, and solenoid loads. The following design procedure can be used to configure the DRV8313.
Related Variants
The following components are covered by the same datasheet.
| Part Number | Manufacturer | Package |
|---|---|---|
| DRV8313 | Texas Instruments | — |
| DRV8313PWP | Texas Instruments | — |
| DRV8313PWPR | Texas Instruments | 28-PowerTSSOP (0.173", 4.40mm Width) |
| DRV8313RHH | Texas Instruments | — |
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.
Get structured datasheet data via API
Get started free