TLE5012B-E5000

Part: TLE5012B — Infineon Technologies AG

Type: GMR-Based Angle Sensor

Description: A 360° angle sensor that detects magnetic field orientation using integrated Giant Magneto Resistance (iGMR) elements, providing 15-bit absolute angle resolution and supporting multiple interfaces including SSC (SPI-compatible), PWM, SPC, HSM, and IIF.

Operating Conditions:

• Supply voltage: 3.0–5.5 V
• Operating temperature: -40 to 150 °C (junction temperature)
• Magnetic field range: 20–80 mT (at Tj = -40 to 150 °C)

Absolute Maximum Ratings:

• Max supply voltage: -0.3 to 7 V
• Max junction/storage temperature: -40 to 150 °C

Key Specs:

• Angle error over lifetime and temperature: Max. 1.0° (with activated auto-calibration)
• Absolute angle resolution: 0.01° (15 bit representation)
• Sine/cosine value representation: 16 bit
• SSC Interface speed: Up to 8 Mbit/s
• Supply current (active mode): Typ. 10 mA (at VDD = 5 V, Tj = 25 °C)
• Supply current (sleep mode): Typ. 10 μA (at VDD = 5 V, Tj = 25 °C)
• Output voltage high (VOH): Min. VDD - 0.4 V (at IOH = -2 mA)
• Output voltage low (VOL): Max. 0.4 V (at IOL = 2 mA)

Features:

• Integrated magnetic field sensing for angle measurement
• 360° angle measurement with revolution counter and angle speed measurement
• Two separate highly accurate single bit SD-ADC
• Bi-directional SSC Interface up to 8Mbit/s
• Supports Safety Integrity Level (SIL) with diagnostic functions and status information
• Interfaces: SSC, PWM, Incremental Interface (IIF), Hall Switch Mode (HSM), Short PWM Code (SPC, based on SENT protocol defined in SAE J2716)
• Output pins can be configured as push-pull or open-drain
• Bus mode operation of multiple sensors on one line is possible with SSC or SPC interface in open-drain configuration
• ESD > 4kV (HBM)
• RoHS compliant (Pb-free package)
• Halogen-free

Applications:

• Electrical commutated motor (e.g. used in Electric Power Steering (EPS))
• Rotary switches
• Steering angle measurements
• General angular sensing

Package:

• PG-DSO-8

• G iant M agneto R esistance (GMR)-based principle
• Integrated magnetic field sensing for angle measurement
• 360° angle measurement with revolution counter and angle speed measurement
• Two separate highly accurate single bit SD-ADC
• 15 bit representation of absolute angle value on the output (resolution of 0.01°)
• 16 bit representation of sine / cosine values on the interface
• Max. 1.0° angle error over lifetime and temperature-range with activated auto-calibration
• Bi-directional SSC Interface up to 8Mbit/s
• Supports Safety Integrity Level (SIL) with diagnostic functions and status information
• Interfaces: SSC, PWM, Incremental Interface (IIF), Hall Switch Mode (HSM), Short PWM Code (SPC, based on SENT protocol defined in SAE J2716)
• Output pins can be configured (programmed or pre-configured) as push-pull or open-drain
• Bus mode operation of multiple sensors on one line is possible with SSC or SPC interface in open-drain configuration
• 0.25 μ m CMOS technology
• Automotive qualified: -40°C to 150°C (junction temperature)
• ESD > 4kV (HBM)
• RoHS compliant (Pb-free package)
• Halogen-free

Figure 2-4 Pin configuration (top view)

Table 4-1 Absolute maximum ratings

Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the device.

The application circuits in this chapter show the various communication possibilities of the TLE5012B. The pin output mode configuration is device-specific and it can be either push-pull or open-drain. The bit IFAB_OD (register IFAB, 0D H ) indicates the output mode for the IFA, IFB and IFC pins. The SSC pins are by default pushpull (bit SSC_OD, register MOD_3, 09 H ).

Figure 3-1 shows a basic block diagram of a TLE5012B with Incremental Interface and SSC configuration. The derivate TLE5012B - E1000 is by default configured with push-pull IFA (IIF_A), IFB (IIF_ B) and IFC (IIF_IDX) pins.

Figure 3-1 Application circuit for TLE5012B with IIF interface and SSC (using internal CLK)

Figure 3-1 shows a basic block diagram of a TLE5012B with Incremental Interface and SSC configuration. The derivate TLE5012B - E1000 is by default configured with push-pull IFA (IIF_A), IFB (IIF_ B) and IFC (IIF_IDX) pins.

In case that the IFA, IFB and IFC pins are configurated via the SSC interface as open-drain pins, three resistors (one for each line) between output line and V DD would be recommended (e.g. 2.2k Ω ).

Figure 3-2 shows a basic block diagram of the TLE5012B with HS Mode and SSC configuration. The derivate TLE5012B - E3005 is by default configurated with push-pull IFA (HS1), IFB (HS2) and IFC (HS3) pins.

Figure 3-2 Application circuit for TLE5012B with HS Mode and SSC (using internal CLK)

Figure 3-2 shows a basic block diagram of the TLE5012B with HS Mode and SSC configuration. The derivate TLE5012B - E3005 is by default configurated with push-pull IFA (HS1), IFB (HS2) and IFC (HS3) pins.

Application Circuits

Figure 3-2 Application circuit for TLE5012B with HS Mode and SSC (using internal CLK)

Figure 6-1 PG-DSO-8 package dimension

Package Information