TCAN1046AV-Q1
Automotive Dual CAN FD TransceiverThe TCAN1046AV-Q1 is a automotive dual can fd transceiver from Texas Instruments. View the full TCAN1046AV-Q1 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
Official TCAN1046AV-Q1 datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Interface ICsTCAN1046AV-Q1 Key Specifications
| Parameter | Value |
|---|---|
| Channels | 2 independent CAN channels |
| Data Rate | up to 8 Mbps (CAN FD), down to 9.2 kbps |
| Standards | ISO 11898-2:2016 |
| Qualification | AEC-Q100 Grade 1 |
| Package Options | VSON-14 4.5x3.0mm, SOIC-14, SOT-23-14 |
| Standby Pin Logic | Active-high (STB) |
| VCC Supply Voltage | 4.5V to 5.5V |
| VIO Supply Voltage | 1.7V to 5.5V |
| Bus Fault Protection | ±58 V |
| Operating Junction Temperature | -40°C to 150°C |
| VCC Rising Undervoltage Detection | 4.2V typ, 4.4V max |
| VIO Rising Undervoltage Detection | 1.56V typ, 1.65V max |
| Receiver Common-Mode Input Voltage | ±12 V |
TCAN1046AV-Q1 Overview
Part: TCAN1046AV-Q1 / TCAN1048AV-Q1 — Texas Instruments
Type: Automotive Dual CAN FD Transceiver
Description: AEC-Q100 Grade 1 dual high-speed CAN FD transceiver with 4.5–5.5 V VCC, 1.7–5.5 V VIO, data rates up to 8 Mbps, ±58 V bus fault protection and standby mode with remote wake-up.
Operating Conditions:
- Supply voltage: VCC 4.5–5.5 V; VIO 1.7–5.5 V
- Operating junction temperature: -40 to 150 °C
- Data rates: up to 8 Mbps (CAN FD); down to 9.2 kbps
Absolute Maximum Ratings:
- Max supply voltage: VCC 6 V; VIO 6 V
- Bus voltage (CANH/CANL): ±58 V
- Max differential bus voltage: ±45 V
- RXD output current: ±8 mA
- Max junction temperature: 165 °C
- Storage temperature: -65 to 150 °C
Key Specs:
- ICC normal mode, recessive, two channels (RL = 50 Ω): 10 mA typ, 15 mA max
- ICC normal mode, dominant two channels (RL = 60 Ω): 95 mA typ, 140 mA max
- ICC standby mode: 0.4 μA typ, 3 μA max
- IIO standby mode: 17 μA typ, 30 μA max
- IIO normal mode, recessive two channels: 50 μA typ, 100 μA max
- UVCC rising: 4.2 V typ, 4.4 V max; falling: 4 V typ (3.5–4.25 V)
- UVVIO rising: 1.56 V typ, 1.65 V max; falling: 1.51 V typ (1.4–1.59 V)
- RθJA: 75.8 °C/W (SOIC), 87.2 °C/W (SOT-23), 38.1 °C/W (VSON)
- ESD: HBM ±4 kV all pins, ±10 kV on CANH/CANL; CDM ±750 V
Features:
- Two high-speed CAN transceivers with independent mode control
- Meets ISO 11898-2:2016 physical layer
- Classical CAN and CAN FD at 2, 5 and 8 Mbps
- Short, symmetrical propagation delays
- Receiver common-mode input range ±12 V
- Supports 12 V and 24 V battery applications
- Bus fault protection ±58 V, undervoltage protection, TXD dominant time-out, thermal shutdown
- Normal and low-power standby modes with remote wake-up (WUP)
- Bus and logic pins high impedance when unpowered; hot-plug capable
- Functional Safety-Capable
- TCAN1046AV: active-high STB; TCAN1048AV: active-low nSTB
Applications:
- Body control modules
- Automotive gateway
- Advanced driver assistance systems (ADAS)
- Infotainment
Package:
- VSON-14 (DMT), 4.50 mm x 3.00 mm
- SOIC-14 (D), 8.65 mm x 3.91 mm (TCAN1046AV-Q1), 8.95 mm x 3.91 mm (TCAN1048AV-Q1)
- SOT-23-14 (DYY), 4.20 mm x 2 mm (TCAN1046AV-Q1)
TCAN1046AV-Q1 Features
- AEC-Q100 (Grade 1): Qualified for automotive applications
- Two high-speed CAN transceivers with independent mode control
- Meets the requirements of ISO 11898-2:2016 physical layer standard
- Functional Safety-Capable
- -Documentation available to aid in functional safety system design
- Support of classical CAN and optimized CAN FD performance at 2, 5, and 8 Mbps
- -Short and symmetrical propagation delays for enhanced timing margin
- I/O voltage range supports 1.7 V to 5.5 V
- Support for 12-V and 24-V battery applications
- Receiver common-mode input voltage: ±12 V
- Protection features:
- -Bus fault protection: ±58 V
- -Undervoltage protection
- -TXD-dominant time-out (DTO)
- Data rates down to 9.2 kbps
- -Thermal-shutdown protection (TSD)
- Operating modes:
- -Normal mode
- -Low power standby mode supporting remote wake-up request
- Optimized behavior when unpowered
- -Bus and logic pins are high impedance (no load to operating bus or application)
- -Hot-plug capable: power-up and power-down glitch-free operation on bus and RXD output
- Junction temperatures from: -40°C to 150°C
- Available in space-saving SOT-23, SOIC (14) and leadless VSON (14) packages (4.5 mm x 3.0 mm) with improved automated optical inspection (AOI) capability
TCAN1046AV-Q1 Applications
- Automotive and Transportation
- -Body control modules
- -Automotive gateway
- -Advanced driver assistance system (ADAS)
- -Infotainment
TCAN1046AV-Q1 Pin Configuration
Figure 7-1. D Package, 14 Pin SOIC, Top View
Table 6-1. Device Comparison Table
Figure 7-2. DYY Package, 14 Pin SOT-23, Top View
Figure 7-3. DMT Package, 14 Pin VSON, Top View
Table 7-1. Pin Functions
| Pins - Name | Pins - No. | Type | Description |
|---|---|---|---|
| TXD1 | 1 | Digital Input | CAN transmit data input channel 1; integrated pull-up |
| GND1 | 2 | GND | Ground connection |
| V CC | 3 | Supply | 5-V supply voltage |
| RXD1 | 4 | Digital Output | CAN receive data output channel 1; tri-state when V IO < UV VIO |
| GND2 | 5 | GND | Ground connection |
| TXD2 | 6 | Digital Input | CAN transmit data input channel 2; integrated pull-up |
| RXD2 | 7 | Digital Output | CAN receive data output channel 2; tri-state when V IO < UV VIO |
| STB2 | 8 | Digital Input | Standby input of channel 2 for mode control; integrated pull-up (TCAN1046AV-Q1) |
| nSTB2 | 8 | Digital Input | Standby input of channel 2 for mode control; inverse logic with integrated pull-down (TCAN1048AV-Q1) |
| CANL2 | 9 | Bus IO | Low-level CAN bus channel 2 input/output line |
| CANH2 | 10 | Bus IO | High-level CAN bus channel 2 input/output line |
| V IO | 11 | Supply | I/O supply voltage |
| CANL1 | 12 | Bus IO | Low-level CAN bus channel 1 input/output line |
Table 7-1. Pin Functions
TCAN1046AV-Q1 Electrical Characteristics
Over recommended operating conditions with TJ = -40 °C to 150 °C (unless otherwise noted), CAN electrical parameters apply to both channels www.ti.com
| PARAMETER | PARAMETER | PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT |
|---|---|---|---|---|---|---|---|
| Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics | Driver Electrical Characteristics |
| Dominant output voltage | CANH | STB = 0 V / nSTB = V IO | 2.75 | 4.5 | V | ||
| V O(DOM) | Normal mode | CANL | TXD = 0 V 50 Ω ≤ R L ≤ 65 Ω, C L = open; See Figure 9-2 and Figure 10-3 | 0.5 | 2.25 | V | |
| V O(REC) | Recessive output voltage Normal mode | CANH and CANL | STB = 0 V / nSTB = V IO TXD = V IO R L = open (no load); See Figure 9-2 and Figure 10-3 | 2 | 0.5 V CC | 3 | V |
| V SYM | Driver symmetry (V O(CANH) + V O(CANL) )/V CC | STB = 0 V / nSTB = V IO TXD = 250 kHz, 1 MHz, 2.5 MHz R L = 60 Ω, C SPLIT = 4.7 nF, C L = open; See Figure 9-2 and Figure 10-3 | 0.9 | 1.1 | V/V | ||
| V SYM_DC | DC output symmetry (V CC - V O(CANH) - V O(CANL) ) | STB = 0 V / nSTB = V IO R L = 60 Ω, C L = open; See Figure 9-2 and Figure 10-3 | -400 | 400 | mV | ||
| V OD(DOM) | Differential output voltage Normal mode Dominant | CANH - CANL | STB = 0 V / nSTB = V IO TXD = 0 V 50 Ω ≤ R L ≤ 65 Ω, C L = open; See Figure 9-2 and Figure 10-3 | 1.5 | 3 | V | |
| CANH - CANL | STB = 0 V / nSTB = V IO TXD = 0 V 45 Ω ≤ R L ≤ 70 Ω, C L = open; See Figure 9-2 and Figure 10-3 | 1.4 | 3.3 | V | |||
| Differential output voltage | STB = 0 V / nSTB = V IO TXD = 0 V R L = 2240 Ω, C L = open; See Figure 9-2 and Figure 10-3 | 1.5 | 5 | V | |||
| V OD(REC) | Normal mode Recessive | CANH - CANL | STB = 0 V / nSTB = V IO TXD = V IO R L = 60 Ω, C L = open; See Figure 9-2 and Figure 10-3 | -120 | 12 | mV | |
| CANH - CANL | STB = 0 V / nSTB = V IO TXD = V IO R L = open, C L = open; See Figure 9-2 and Figure 10-3 | -50 | 50 | mV | |||
| V O(STB) | Bus output voltage Standby mode | CANH | STB = V / nSTB = 0 V | -0.1 | 0.1 | V | |
| V O(STB) | CANL | IO R L = open; | -0.1 | 0.1 | V | ||
| V O(STB) | CANH - CANL | See Figure 9-2 and Figure 10-3 | -0.2 | 0.2 | V | ||
| I OS(SS_DOM) | Short-circuit steady-state output current, dominant mode | Short-circuit steady-state output current, dominant mode | STB = 0 V / nSTB = V IO TXD = 0 V V (CANH) = -15 V to 40 V, CANL = open; See Figure 9-8 and Figure 10-3 | -115 | mA | ||
| I OS(SS_DOM) | Normal | Normal | STB = 0 V / nSTB = V IO TXD = 0 V V (CAN_L) = -15 V to 40 V, CANH = open; See Figure 9-8 and Figure 10-3 | 115 | mA | ||
| I OS(SS_REC) | Short-circuit steady-state output current, recessive Normal mode | Short-circuit steady-state output current, recessive Normal mode | STB = 0 V / nSTB = V IO TXD = V IO -27 V ≤ V BUS ≤ 32 V, where V BUS = CANH = CANL; See Figure 9-8 and Figure 10-3 | -5 | 5 | mA | |
| Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics | Receiver Electrical Characteristics |
| V IT | Input threshold voltage Normal mode | Input threshold voltage Normal mode | STB = 0 V / nSTB = V IO -12 V ≤ V CM ≤ 12 V; See Figure 9-3 and Table 10-5 | 500 | 900 | mV | |
| V IT(STB) | Input threshold Standby mode | Input threshold Standby mode | STB = V IO / nSTB = 0 V -12 V ≤ V CM ≤ 12 V; See Figure 9-3 and Table 10-5 | 400 | 1150 | mV |
TCAN1046AV-Q1 Absolute Maximum Ratings
(1) (2)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| V CC | Supply voltage | -0.3 | 6 | V |
| V IO | Supply voltage I/O level shifter | -0.3 | 6 | V |
| V BUS | CAN Bus I/O voltage CANH1, CANL1, CANH2, CANL2 | -58 | 58 | V |
| V DIFF | Max differential voltage between CANHx and CANLx | -45 | 45 | V |
| V Logic_Input | Logic input terminal voltage | -0.3 | 6 | V |
| V RXDx | RXDx output terminal voltage range | -0.3 | 6 | V |
| I O(RXDx) | RXDx output current | -8 | 8 | mA |
| T J | Junction temperature | -40 | 165 | °C |
| T STG | Storage temperature | -65 | 150 | °C |
- (2) All voltage values, except differential I/O bus voltages, are with respect to ground terminal.
TCAN1046AV-Q1 Recommended Operating Conditions
| MIN | NOM | MAX | UNIT | ||
|---|---|---|---|---|---|
| V CC | Supply voltage | 4.5 | 5 | 5.5 | V |
| V IO | Supply voltage for I/O level shifter | 1.7 | 5.5 | V | |
| I OH(RXDx) | RXDx terminal high-level output current | -1.5 | mA | ||
| I OL(RXDx) | RXDx terminal low-level output current | 1.5 | mA | ||
| T J | Operating junction temperature | -40 | 150 | °C |
TCAN1046AV-Q1 Thermal Information
| (1) - THERMAL METRIC | TCAN1046AV-Q1 / TCAN1048AV-Q1 - D (SOIC) | TCAN1046AV-Q1 / TCAN1048AV-Q1 - DYY (SOT) | TCAN1046AV-Q1 / TCAN1048AV-Q1 - DMT (VSON) | UNIT | |
|---|---|---|---|---|---|
| R θJA | Junction-to-ambient thermal resistance | 75.8 | 87.2 | 38.1 | °C /W |
| R θJC(top) | Junction-to-case (top) thermal resistance | 35.8 | 35.2 | 38.7 | °C /W |
| R θJB | Junction-to-board thermal resistance | 37.4 | 31.6 | 15.0 | °C /W |
| Ψ JT | Junction-to-top characterization parameter | 6.6 | 11.2 | 2.0 | °C /W |
| Ψ JB | Junction-to-board characterization parameter | 37.0 | 31.5 | 15.0 | °C /W |
| R θJC(bot) | Junction-to-case (bottom) thermal resistance | - | - | 5.9 | °C /W |
TCAN1046AV-Q1 Typical Application
Figure 11-1 shows a typical configuration for 5 V system using the TCAN104xAV-Q1. The bus termination is shown for illustrative purposes.
Figure 11-1. Transceiver Application Using 5 V I/O Connections
Figure 11-1 shows a typical configuration for 5 V system using the TCAN104xAV-Q1. The bus termination is shown for illustrative purposes.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| TCAN1048AV-Q1 | Texas Instruments | — |
Other Interface ICs
- TCA6424ARGJR – Texas Instruments, I2C and SMBus I/O Expander
- BQ25895 – Texas Instruments, I2C Controlled Single Cell 5-A Fast Charger with MaxChargeTM for High Input Voltage and Adjustable Voltage 3.1-A Boost Operation
- CH340N – WCH, USB to Serial Bridge IC
- SE050C2HQ1/Z01SDZ – NXP Semiconductors, IoT Secure Element
- ADM3053BRWZ – Analog Devices, Signal and Power Isolated CAN Transceiver
- ADM3053BRWZ-REEL7 – Analog Devices, Signal and Power Isolated CAN Transceiver
- BQ25895RTWR.A – Texas Instruments, I2C Controlled Single Cell 5-A Fast Charger with MaxChargeTM for High Input Voltage and Adjustable Voltage 3.1-A Boost Operation
- CH334 – WCH, 4-Port USB 2.0 Hub Controller
All Interface ICs datasheetsAll Texas Instruments datasheets (2,418)
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.
Ask your AI agent about the TCAN1046AV-Q1
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the TCAN1046AV-Q1 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.