ESP32-D0WDR2-V3
Wi-Fi and Bluetooth SoCThe ESP32-D0WDR2-V3 is a wi-fi and bluetooth soc from Espressif Systems. View the full ESP32-D0WDR2-V3 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
ESP32-D0WDR2-V3 shares its datasheet with ESP32-DevKitC-32E, whose page lists every part number it covers.
Official ESP32-D0WDR2-V3 datasheet (PDF) — the source this page was extracted from.
ESP32-D0WDR2-V3 Key Specifications
| Parameter | Value |
|---|---|
| Contents | Board(s) |
| Frequency | 2.4GHz |
| Packaging | Bulk |
| RoHS | Compliant |
| Standard Pack Qty | 252 |
| Type | Transceiver; 802.11 b/g/n (Wi-Fi, WiFi, WLAN), Bluetooth® Smart Ready 4.x Dual Mode (BLE) |
| Utilized IC / Part | ESP32-WROOM-32E |
ESP32-D0WDR2-V3 Overview
Part: ESP32-DevKitC-32E (ESP32 Series SoC) — Espressif Systems
Type: 2.4 GHz Wi-Fi + Bluetooth / Bluetooth LE SoC
Description: Dual-core Xtensa LX6 32-bit SoC at up to 240 MHz with 802.11b/g/n Wi-Fi (up to 150 Mbps), Bluetooth v4.2 BR/EDR + Bluetooth LE, 520 KB SRAM and 34 GPIOs.
Operating Conditions:
- Supply voltage: 2.3–3.6 V (VDDA, VDD3P3, VDD3P3_RTC pin supply range)
- Max CPU clock: 240 MHz
- VDD_SDIO output: 1.8 V or same as VDD3P3_RTC
Absolute Maximum Ratings:
- Max supply voltage: 3.6 V (VDDA, VDD3P3, VDD3P3_RTC, VDD3P3_CPU, VDD_SDIO; min −0.3 V)
- Max continuous current: 1200 mA (cumulative IO output current)
- Storage temperature: −40 to 150 °C
Key Specs:
- CPU: Xtensa single-/dual-core 32-bit LX6, up to 240 MHz; 539.98 CoreMark (1 core), 1079.96 CoreMark (2 cores)
- Memory: 448 KB ROM, 520 KB SRAM, 16 KB RTC SRAM
- Wi-Fi: 802.11b/g/n, 2.4 GHz, up to 150 Mbps
- Bluetooth: v4.2 BR/EDR and LE, +9 dBm transmit power, −94 dBm Bluetooth LE sensitivity
- Deep-sleep power consumption: 10 μA
- ADC: 12-bit SAR, up to 18 channels; two 8-bit DACs; 10 touch sensors
- GPIOs: 34 programmable
- Peripheral interfaces: 4 SPI, 2 I2S, 2 I2C, 3 UART, SD/eMMC/SDIO host, SDIO/SPI slave, TWAI (CAN 2.0), Ethernet MAC
Features:
- Four virtual Wi-Fi interfaces; simultaneous Station, SoftAP and promiscuous modes
- Class-1/2/3 Bluetooth transmitter without external power amplifier
- Five power modes: Active, Modem-sleep, Light-sleep, Deep-sleep, Hibernation
- Ultra-Low-Power coprocessor
- Secure boot and flash encryption
- 1024-bit OTP
- AES, SHA-2, RSA and RNG hardware acceleration
- Motor PWM, LED PWM (up to 16 channels), RMT, pulse counter
Applications:
- Smart home
- Industrial automation
- Health care
- Consumer electronics
- Smart agriculture
- POS machines
- Service robots
- Audio devices
- IoT sensor hubs and data loggers
- Video streaming cameras
- Speech and image recognition
- SDIO Wi-Fi + Bluetooth networking card
Package:
- QFN48 (6×6 mm)
- QFN48 (5×5 mm)
ESP32-D0WDR2-V3 Features
- Programmable data transfer length, in multiples of 1 byte
- Four-line full-duplex/half-duplex communication and three-line half-duplex communication support
- Master mode and slave mode
- Programmable CPOL and CPHA
- Programmable clock
For details, see ESP32 Technical Reference Manual > Chapter SPI Controller .
For SPI, the pins are multiplexed with GPIO6 ~ GPIO11 via the IO MUX. For HSPI, the pins are multiplexed with GPIO2, GPIO4, GPIO12 ~ GPIO15 via the IO MUX. For VSPI, the pins are multiplexed with GPIO5, GPIO18 ~ GPIO19, GPIO21 ~ GPIO23 via the IO MUX.
For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix .
ESP32-D0WDR2-V3 Applications
With low power consumption, ESP32 is an ideal choice for IoT devices in the following areas:
- Smart Home
- Industrial Automation
- Health Care
- Consumer Electronics
- Smart Agriculture
- POS Machines
- Service Robot
- Audio Devices
- Generic Low-power IoT Sensor Hubs
- Generic Low-power IoT Data Loggers
- Cameras for Video Streaming
- Speech Recognition
- Image Recognition
- SDIO Wi-Fi + Bluetooth Networking Card
Check the link or the QR code to make sure that you use the latest version of this document:
https://www.espressif.com/documentation/esp32_datasheet_en.pdf
ESP32-D0WDR2-V3 Pin Configuration
Table 4-6. Peripheral Pin Configurations
| Interface | Signal | Pin | Function |
|---|---|---|---|
| ADC | ADC1_CH0 | SENSOR_VP | Two 12-bit SAR ADCs |
| ADC | ADC1_CH1 | SENSOR_CAPP | Two 12-bit SAR ADCs |
| ADC | ADC1_CH2 | SENSOR_CAPN | Two 12-bit SAR ADCs |
| ADC | ADC1_CH3 | SENSOR_VN | Two 12-bit SAR ADCs |
| ADC | ADC1_CH4 | 32K_XP | Two 12-bit SAR ADCs |
| ADC | ADC1_CH5 | 32K_XN | Two 12-bit SAR ADCs |
| ADC | ADC1_CH6 | VDET_1 | Two 12-bit SAR ADCs |
| ADC | ADC1_CH7 | VDET_2 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH0 | GPIO4 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH1 | GPIO0 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH2 | GPIO2 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH3 | MTDO | Two 12-bit SAR ADCs |
| ADC | ADC2_CH4 | MTCK | Two 12-bit SAR ADCs |
| ADC | ADC2_CH5 | MTDI | Two 12-bit SAR ADCs |
| ADC | ADC2_CH6 | MTMS | Two 12-bit SAR ADCs |
| ADC | ADC2_CH7 | GPIO27 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH8 | GPIO25 | Two 12-bit SAR ADCs |
| ADC | ADC2_CH9 | GPIO26 | Two 12-bit SAR ADCs |
| DAC | DAC_1 | GPIO25 | Two 8-bit DACs |
| DAC | DAC_2 | GPIO26 | Two 8-bit DACs |
| DAC | TOUCH0 | GPIO4 | Two 8-bit DACs |
| DAC | TOUCH1 | GPIO0 | Two 8-bit DACs |
| DAC | TOUCH2 | GPIO2 | Two 8-bit DACs |
| DAC | TOUCH3 | MTDO | Two 8-bit DACs |
| Touch Sensor | TOUCH4 | MTCK | Capacitive |
| DAC | TOUCH5 | MTDI | Two 8-bit DACs |
| DAC | TOUCH6 | MTMS | Two 8-bit DACs |
| DAC | TOUCH7 | GPIO27 | Two 8-bit DACs |
| DAC | TOUCH8 | 32K_XN | Two 8-bit DACs |
| DAC | TOUCH9 | 32K_XP | Two 8-bit DACs |
| JTAG | MTDI | MTDI | JTAG for software debugging |
| JTAG | MTCK | MTCK | JTAG for software debugging |
| JTAG | MTMS | MTMS | JTAG for software debugging |
| JTAG | MTDO | MTDO | JTAG for software debugging |
| Interface | Signal | Pin | Function |
|---|---|---|---|
| SD/SDIO/MMC Host Controller | HS2_CLK | MTMS | Supports SD memory card V3.01 standard |
| SD/SDIO/MMC Host Controller | HS2_CMD | MTDO | Supports SD memory card V3.01 standard |
| SD/SDIO/MMC Host Controller | HS2_DATA0 | GPIO2 | Supports SD memory card V3.01 standard |
| SD/SDIO/MMC Host Controller | HS2_DATA1 | GPIO4 | Supports SD memory card V3.01 standard |
| SD/SDIO/MMC Host Controller | HS2_DATA2 | MTDI | Supports SD memory card V3.01 standard |
| SD/SDIO/MMC Host Controller | HS2_DATA3 | MTCK | Supports SD memory card V3.01 standard |
| Motor PWM | PWM0_OUT0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM1_OUT_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM0_FLT_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM1_FLT_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM0_CAP_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM1_CAP_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM0_SYNC_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| Motor PWM | PWM1_SYNC_IN0 ~ 2 | Any GPIO Pins | Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. |
| SDIO/SPI Slave Controller | SD_CLK | MTMS MTDO | SDIO interface that conforms to the industry standard SDIO 2.0 card specification |
| SDIO/SPI Slave Controller | SD_CMD | SDIO interface that conforms to the industry standard SDIO 2.0 card specification | |
| SDIO/SPI Slave Controller | SD_DATA0 | GPIO2 | SDIO interface that conforms to the industry standard SDIO 2.0 card specification |
| SDIO/SPI Slave Controller | SD_DATA1 | GPIO4 | SDIO interface that conforms to the industry standard SDIO 2.0 card specification |
| SDIO/SPI Slave Controller | SD_DATA2 | MTDI | SDIO interface that conforms to the industry standard SDIO 2.0 card specification |
| SDIO/SPI Slave Controller | SD_DATA3 | MTCK | SDIO interface that conforms to the industry standard SDIO 2.0 card specification |
| UART | U0RXD_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U0CTS_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U0DSR_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U0TXD_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U0RTS_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U0DTR_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U1RXD_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U1CTS_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U1RTS_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U2RXD_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U2CTS_in | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U2TXD_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| UART | U2RTS_out | Any GPIO Pins | Three UART devices with hardware flow-control and DMA |
| I2C | I2CEXT0_SCL_in | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT0_SDA_in | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT1_SCL_in | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT1_SDA_in | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT0_SCL_out | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT0_SDA_out | Any GPIO Pins | Two I2C devices in slave or master mode |
| I2C | I2CEXT1_SDA_out | Any GPIO Pins | Two I2C devices in slave or master mode |
Table 4-6. Peripheral Pin Configurations
| Interface | Signal | Pin | Function |
|---|---|---|---|
| LED PWM | ledc_hs_sig_out0 ~ 7 | Any GPIO | 16 independent channels @80 MHz clock/RTC CLK. Duty accuracy: 16 bits. |
| I2S | ledc_ls_sig_out0 ~ 7 I2S0I_DATA_in0 ~ 15 I2S0O_BCK_in I2S0O_WS_in I2S0I_BCK_in I2S0I_WS_in I2S0I_H_SYNC I2S0I_V_SYNC I2S0I_H_ENABLE I2S0O_BCK_out | ||
| I2S0O_WS_out | Stereo input and output from/to the audio | ||
| I2S0I_BCK_out | codec; parallel LCD data output; parallel | ||
| I2S0I_WS_out | camera data input. | ||
| I2S0O_DATA_out0 ~ 23 I2S1I_DATA_in0 ~ 15 | Any GPIO | ||
| I2S1O_BCK_in | Note: I2S0_CLK and I2S1_CLK can only | ||
| I2S1O_WS_in | be mapped to GPIO0, U0RXD (GPIO3), | ||
| I2S1I_BCK_in | U0TXD (GPIO1) via IO MUX by selecting | ||
| I2S1I_WS_in | GPIO functions CLK_OUT1, CLK_OUT2, | ||
| I2S1I_H_SYNC | and CLK_OUT3. For more information, | ||
| I2S1I_V_SYNC | see ESP32 Technical Reference Manual | ||
| I2S1I_H_ENABLE | Chapter IO_MUX and GPIO Matrix > Table | ||
| I2S1O_BCK_out I2S1O_WS_out I2S1I_BCK_out I2S1I_WS_out I2S1O_DATA_out0 ~ 23 | IO MUX Pad Summary . | ||
| I2S0_CLK | GPIO0, U0RXD, | ||
| I2S1_CLK | or U0TXD | ||
| RMT | RMT_SIG_IN0 ~ 7 | Any GPIO Pins | Eight channels for an IR transmitter and receiver of various waveforms Standard SPI consists of clock, |
| RMT | RMT_SIG_OUT0 ~ 7 | Any GPIO Pins | Eight channels for an IR transmitter and receiver of various waveforms Standard SPI consists of clock, |
| RMT | HSPIQ_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | HSPID_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | HSPICLK_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | HSPI_CS0_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | HSPI_CS1_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| General Purpose | HSPI_CS2_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| SPI | VSPIQ_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | VSPID_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | VSPICLK_in/_out | Any GPIO Pins | can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; |
| RMT | VSPI_CS0_in/_out | Any GPIO Pins | Up to 64 bytes of FIFO and DMA. |
| RMT | VSPI_CS1_out | Any GPIO Pins | • |
| Interface | Signal | Pin | Function |
| Parallel QSPI | SPIHD | SD_DATA_2 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | SPIWP | SD_DATA_3 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | SPICS0 | SD_CMD | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | SPICLK | SD_CLK | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | SPIQ | SD_DATA_0 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | SPID | SD_DATA_1 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | HSPICLK | MTMS | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | HSPICS0 | MTDO | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | HSPIQ | MTDI | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | HSPID | MTCK | external flash and SRAM |
| Parallel QSPI | HSPIHD | GPIO4 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | HSPIWP | GPIO2 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPICLK | GPIO18 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPICS0 | GPIO5 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPIQ | GPIO19 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPID | GPIO23 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPIHD | GPIO21 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| Parallel QSPI | VSPIWP | GPIO22 | Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the |
| EMAC_TX_CLK | GPIO0 | Ethernet MAC with MII/RMII interface | |
| EMAC_RX_CLK | GPIO5 | ||
| EMAC_TX_EN | GPIO21 | ||
| EMAC_TXD0 | GPIO19 | ||
| EMAC_TXD1 | GPIO22 | ||
| EMAC_TXD2 | MTMS | ||
| EMAC_TXD3 | MTDI | ||
| EMAC_RX_ER | MTCK | ||
| EMAC_RX_DV | GPIO27 | ||
| EMAC_RXD0 | GPIO25 | ||
| EMAC | EMAC_RXD1 | GPIO26 | |
| EMAC_RXD2 | U0TXD | ||
| EMAC_RXD3 | MTDO | ||
| EMAC_CLK_OUT | GPIO16 | ||
| EMAC_CLK_OUT_180 | GPIO17 | ||
| EMAC_TX_ER | GPIO4 | ||
| EMAC_MDC_out | Any GPIO Pins | ||
| EMAC_MDI_in | Any GPIO Pins | ||
| EMAC_MDO_out | Any GPIO Pins | ||
| EMAC_CRS_out | Any GPIO Pins | ||
| EMAC_COL_out | Any GPIO Pins |
| Interface | Signal | Pin | Function |
|---|---|---|---|
| Pulse Counter | pcnt_sig_ch0_in0 pcnt_sig_ch1_in0 pcnt_ctrl_ch0_in0 pcnt_ctrl_ch1_in0 pcnt_sig_ch0_in1 pcnt_sig_ch1_in1 pcnt_ctrl_ch0_in1 pcnt_ctrl_ch1_in1 pcnt_sig_ch0_in2 pcnt_sig_ch1_in2 pcnt_ctrl_ch0_in2 pcnt_ctrl_ch1_in2 pcnt_sig_ch0_in3 pcnt_sig_ch1_in3 pcnt_ctrl_ch0_in3 pcnt_ctrl_ch1_in3 pcnt_sig_ch0_in4 pcnt_sig_ch1_in4 pcnt_ctrl_ch0_in4 pcnt_ctrl_ch1_in4 pcnt_sig_ch0_in5 pcnt_sig_ch1_in5 pcnt_ctrl_ch0_in5 pcnt_ctrl_ch1_in5 pcnt_sig_ch0_in6 pcnt_sig_ch1_in6 pcnt_ctrl_ch0_in6 pcnt_ctrl_ch1_in6 pcnt_sig_ch0_in7 pcnt_sig_ch1_in7 pcnt_ctrl_ch0_in7 pcnt_ctrl_ch1_in7 | Any GPIO Pins | Operating in seven different modes, the pulse counter captures pulse and counts pulse edges. |
| TWAI | twai_rx | Any GPIO Pins | Compatible with ISO 11898-1 protocol (CAN Specification 2.0) |
| TWAI | twai_tx | Any GPIO Pins | Compatible with ISO 11898-1 protocol (CAN Specification 2.0) |
| TWAI | twai_bus_off_on | Any GPIO Pins | Compatible with ISO 11898-1 protocol (CAN Specification 2.0) |
| TWAI | twai_clkout | Any GPIO Pins | Compatible with ISO 11898-1 protocol (CAN Specification 2.0) |
ESP32-D0WDR2-V3 Electrical Characteristics
Table 5-3. DC Characteristics (3.3 V, 25 °C)
| Parameter | Description | Description | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| C IN | Pin capacitance | Pin capacitance | - | 2 | - | pF |
| V IH | High-level input voltage | High-level input voltage | 0.75 × VDD 1 | - | VDD 1 + 0.3 | V |
| V IL | Low-level input voltage | Low-level input voltage | - 0.3 | - | 0.25 × VDD 1 | V |
| I IH | High-level input current | High-level input current | - | - | 50 | nA |
| I IL | Low-level input current | Low-level input current | - | - | 50 | nA |
| V OH | High-level output voltage | High-level output voltage | 0.8 × VDD 1 | - | - | V |
| V OL | Low-level output voltage | Low-level output voltage | - | - | 0.1 × VDD 1 | V |
| I OH | High-level source current (VDD 1 = 3.3 V, V OH >= 2.64 V, | VDD3P3_CPU power domain 1 , 2 | - | 40 | - | mA |
| I OH | High-level source current (VDD 1 = 3.3 V, V OH >= 2.64 V, | VDD3P3_RTC power domain 1 , 2 | - | 40 | - | mA |
| I OH | High-level source current (VDD 1 = 3.3 V, V OH >= 2.64 V, | VDD_SDIO power domain 1 , 3 | - | 20 | - | mA |
| I OL | Low-level sink current (VDD 1 = 3.3 V, V OL = 0.495 V, output drive strength set to the maximum) | Low-level sink current (VDD 1 = 3.3 V, V OL = 0.495 V, output drive strength set to the maximum) | - | 28 | - | mA |
| R PU | Resistance of internal pull-up resistor | Resistance of internal pull-up resistor | - | 45 | - | k Ω |
| R PD | Resistance of internal pull-down resistor | Resistance of internal pull-down resistor | - | 45 | - | k Ω |
| V IH _ nRST | Chip reset release voltage (CHIP_PU voltage is within the specified range) | Chip reset release voltage (CHIP_PU voltage is within the specified range) | 0.75 × VDD 1 | - | VDD 1 + 0.3 | V |
| V IL _ nRST | Low-level input voltage of CHIP_PU to shut down the chip | Low-level input voltage of CHIP_PU to shut down the chip | - | - | 0.6 | V |
- For VDD3P3_CPU and VDD3P3_RTC power domain, per-pin current sourced in the same domain is gradually reduced from around 40 mA to around 29 mA, V OH >=2.64 V, as the number of current-source pins increases.
- For VDD_SDIO power domain, per-pin current sourced in the same domain is gradually reduced from around 30 mA to around 10 mA, V OH >=2.64 V, as the number of current-source pins increases.
ESP32-D0WDR2-V3 Absolute Maximum Ratings
Stresses above those listed in T able 5-1 Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and normal operation of the device at these or any other conditions beyond those indicated in Section 5.2 Recommended Power Supply Characteristics is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Table 5-1. Absolute Maximum Ratings
| Parameter | Description | Min | Max | Unit |
|---|---|---|---|---|
| VDDA, VDD3P3, VDD3P3_RTC, VDD3P3_CPU, VDD_SDIO | Allowed input voltage | - 0.3 | 3.6 | V |
| I output 1 | Cumulative IO output current | - | 1200 | mA |
| T STORE | Storage temperature | - 40 | 150 | °C |
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| ESP32 | Espressif Systems | ESP32-WROOM-32E (18.0 x 25.5 x 3.1 mm) |
| ESP32-D0WD | Espressif Systems | QFN 5*5 |
| ESP32-D0WD-V3 | Espressif Systems | 48-VFQFN Exposed Pad |
| ESP32-D0WDQ6 | Espressif Systems | QFN 6*6 |
| ESP32-D0WDQ6-V3 | Espressif Systems | QFN 6*6 |
| ESP32-D2WD | Espressif Systems | — |
| ESP32-DevKitC-32E | Espressif Systems | QFN 5*5 |
| ESP32-S0WD | Espressif Systems | QFN 5*5 |
| ESP32-U4WDH | Espressif Systems | 48-QFN |
More datasheets
Ask your AI agent about the ESP32-D0WDR2-V3
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the ESP32-D0WDR2-V3 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.