Skip to main content

TPS610993

The TPS610993 is an electronic component from Texas Instruments. View the full TPS610993 datasheet below including electrical characteristics, absolute maximum ratings.

Manufacturer

Texas Instruments

Category

Voltage Regulators - Switching

Pin Configuration

图 6-1. YFF Package 6-Pin YFF Top View

图 6-2. DRV Package 6-Pin DRV Top View

表 6-1. Pin Functions

PINPINPINTYPEDESCRIPTION
NAMEYFFDRVTYPEDESCRIPTION
VINA16IIC power supply input
SWB15PWRSwitch pin of the converter. It is connected to the inductor
ENC14IEnable logic input. Logic high voltage enables the device; logic low voltage disables the device. Do not leave it floating.
GNDA21PWRGround
VOUTB22PWRBoost converter output
FBC23IVoltage feedback of adjustable output voltage. Connect to the center tap of a resistor divider to program the output voltage. Connect to GND pin for fixed output voltage versions.
PowerPad7Connect to GND

Electrical Characteristics

TJ = -40°C to 125°C and VIN = 0.7 V to 5.5 V. Typical values are at V IN = 3.7 V, TJ = 25°C, unless otherwise noted.

PARAMETERVersionTEST CONDITIONSMINTYPMAXUNIT
POWER SUPPLYPOWER SUPPLYPOWER SUPPLYPOWER SUPPLYPOWER SUPPLYPOWER SUPPLYPOWER SUPPLYPOWER SUPPLY
V INInput voltage rangeTPS61099x0.75.5V
V UVLOInput under voltage lockout thresholdTPS61099xV IN rising0.60.7V
UVLO hysteresisTPS61099x200mV
Quiescent current into VIN pinTPS61099xIC enabled, no Load, no Switching T J = -40 °C to 85 °C0.41.1μA
I QQuiescent current into VOUT pinTPS61099xIC enabled, no Load, no Switching, Boost or Down Mode T J = -40 °C to 85 °C0.61.5μA
I SDShutdown current into VIN pinTPS61099xIC disabled, V IN = 3.7 V, V OUT = 0 V T J = -40 °C to 85 °C0.51.6μA
OUTPUTOUTPUTOUTPUTOUTPUTOUTPUTOUTPUTOUTPUTOUTPUT
V OUTOutput voltage rangeTPS610991.85.5V
TPS610997VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		4.905.00
5.15		5.10V
TPS610994VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		3.233.30
3.4		3.37V
TPS610993VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		2.943.0
3.1		3.06V
Output accuracyTPS610996VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		4.44.5
4.63		4.6V
TPS610992VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		2.452.5
2.58		2.55V
TPS610995VIN < VOUT, PWM mode
VIN < VOUT, PFM mode		3.533.6
3.71		3.67V
V REFFeedback reference voltageTPS61099V IN < V OUT , PWM mode0.981.001.02V
TPS61099V IN < V OUT , PFM mode1.03V
V OVPOutput overvoltage protection thresholdTPS61099xV OUT rising5.65.86.0V
OVP hysteresisTPS61099x100200mV
I FB_LKGLeakage current into FB pinTPS61099xV FB = 1.0 V1050nA
POWER SWITCHPOWER SWITCHPOWER SWITCHPOWER SWITCH
V OUT = 5.0 V		POWER SWITCHPOWER SWITCH
250		POWER SWITCHPOWER SWITCH
m Ω
R DS(on)_LSLow side switch on resistanceTPS61099xV OUT = 3.3 V
V OUT = 1.8 V		300
400		m Ω
m Ω
V OUT = 5.0 V300350m Ω
R DS(on)_HSRectifier on resistanceTPS61099xV OUT = 3.3 V350450m Ω
V OUT = 1.8 V
V OUT = 5.0 V		500
350		750m Ω
mA
I LHInductor current rippleTPS61099xV OUT = 3.3 V
V OUT = 1.8 V		300
250		mA
mA
I LIMCurrent limit thresholdTPS61099xV OUT ≥ 2.5 V, boost operation0.811.25A
V OUT < 2.5 V, boost operation0.50.75A
I SW_LKGLeakage current into SW pin (from SW pin to GND)TPS61099xV SW = 5.0 V, no switch, T J = -40 °C to 85 °C200nA

JULY 2016

Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1)

MINMAXUNIT
Voltage range at terminals (2)VIN, SW, VOUT, FB, EN-0.36V
Operating junction temperature, T J- 40150°C
Storage temperature range, T stg- 65150°C

Recommended Operating Conditions

MINNOMMAXUNIT
V INInput voltage range0.75.5V
V OUTOutput voltage range1.85.5V
LInductor0.72.22.86μH
C INInput capacitor1.010μF
C OUTOutput capacitor1020100μF
T JOperating virtual junction temperature- 40125°C

Thermal Information

TPS61099TPS61099
THERMAL METRIC (1)YFF (6 BALLS, WCSP)DRV(6 PINS, WSON)
R θ JAJunction-to-ambient thermal resistance134.471.7
R θ JCtopJunction-to-case (top) thermal resistance0.983.0
R θ JBJunction-to-board thermal resistance36.133.9
ψ JTJunction-to-top characterization parameter0.12.7
ψ JBJunction-to-board characterization parameter36.233.4
R θ JCbotJunction-to-case (bottom) thermal resistanceN/A14.4

Typical Application

The TPS61099x is a synchronous boost converter designed to operate at a wide input voltage from 0.7 V to 5.5 V with 1-A peak switch current limit. The device adopts a hysteretic control scheme so the operating frequency is not a constant value, which varies with different input/output voltages and inductor values. It only consumes 1μA quiescent current under light load condition. It also supports true shutdown to disconnect the load from the input in order to minimize the leakage current. Therefore, it is very suitable for alkaline battery, coin-cell battery, Li-ion or Li-polymer battery powered systems to extend the battery running time.

Related Variants

The following components are covered by the same datasheet.

Part NumberManufacturerPackage
TPS61099Texas Instruments—
TPS610991Texas Instruments—
TPS610992Texas Instruments—
TPS610992YFFRTexas Instruments—
TPS610992YFFTTexas Instruments—
TPS610993YFFRTexas Instruments—
TPS610993YFFTTexas Instruments—
TPS610994Texas Instruments—
TPS610994YFFRTexas Instruments—
TPS610994YFFTTexas Instruments—
TPS610995Texas Instruments—
TPS610995DRVRTexas Instruments—
TPS610995DRVTTexas Instruments—
TPS610995YFFRTexas Instruments—
TPS610995YFFTTexas Instruments—
TPS610996Texas Instruments—
TPS610996YFFRTexas Instruments—
TPS610996YFFTTexas Instruments—
TPS610997Texas Instruments—
TPS610997YFFRTexas Instruments—
TPS610997YFFTTexas Instruments—
TPS61099DRVRTexas Instruments6-WDFN Exposed Pad
TPS61099XTexas Instruments—
TPS61099YFFRTexas Instruments
TPS61099YFFTTexas Instruments—
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Get structured datasheet data via API

Get started free