Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

TLV9001T

Operational Amplifier

The TLV9001T is a operational amplifier from Texas Instruments. View the full TLV9001T datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

TLV9001T shares its datasheet with TLV9001, whose page lists every part number it covers.

Official TLV9001T datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Operational Amplifiers

Package

SC70-5

TLV9001T Key Specifications

ParameterValue
Input/OutputRail-to-rail input and output
Broadband Noise27 nV/√Hz
Package Body Size1.25 mm × 2.00 mm
Input Bias Current5 pA
Input Offset Voltage±0.4 mV
Supply Voltage Range1.8V to 5.5V
Unity-Gain Bandwidth1 MHz
Capacitive Load Drive500 pF
Shutdown Quiescent Current0.5 µA typ (1.5 µA max), S-variants only
Operating Temperature Range-40°C to 125°C
Quiescent Current Per Channel60 µA typ (75-77 µA max at 5.5V)

TLV9001T Overview

Part: TLV9001IDBVR — Texas Instruments (TLV9001 single-channel, SOT-23-5 package; TLV900x family)

Type: Low-Power Rail-to-Rail Input/Output Operational Amplifier

Description: 1.8–5.5 V, 1 MHz unity-gain bandwidth CMOS op amp with rail-to-rail input and output, ±0.4 mV typical offset voltage and 60 μA/channel quiescent current.

Operating Conditions:

  • Supply voltage: 1.8–5.5 V
  • Operating (specified) temperature: -40 to 125 °C
  • Capacitive-load drive: 500 pF

Absolute Maximum Ratings:

  • Max supply voltage (V+) - (V-): 7 V
  • Common-mode input range: (V-) - 0.5 V to (V+) + 0.5 V
  • Signal input pin current: ±10 mA
  • Output short-circuit: continuous
  • Max junction temperature: 150 °C
  • Storage temperature: -65 to 150 °C

Key Specs:

  • Unity-gain bandwidth: 1 MHz
  • Input offset voltage: ±0.4 mV
  • Input bias current: 5 pA
  • Broadband noise: 27 nV/√Hz
  • Quiescent current: 60 μA per channel
  • Rail-to-rail input and output
  • Unity-gain stable
  • Shutdown variants (TLV900xS): standby current typically below 1 μA

Features:

  • Scalable CMOS amplifier for low-cost applications
  • Internal RFI and EMI filter
  • No phase reversal in overdrive
  • Resistive open-loop output impedance eases stabilization with larger capacitive loads
  • Operational down to 1.8 V
  • Extended temperature range: -40 °C to 125 °C

Applications:

  • Sensor signal conditioning
  • Power modules
  • Active filters
  • Low-side current sensing
  • Smoke and motion detectors
  • Wearable devices
  • Appliances
  • EPOS and barcode scanners
  • HVAC
  • Motor control (AC induction)

Package:

  • SOT-23 (5), 1.60 mm × 2.90 mm (TLV9001 single-channel)
  • Other TLV9001 packages: SC70 (5), SOT-553 (5, preview), X2SON (5)

TLV9001T Features

  • Scalable CMOS amplifier for low-cost applications
  • Rail-to-rail input and output
  • Low input offset voltage: ±0.4 mV
  • ·
  • Unity-gain bandwidth: 1 MHz
  • Low broadband noise: 27 nV/√Hz
  • Low input bias current: 5 pA
  • Low quiescent current: 60 μA/Ch
  • Unity-gain stable
  • Internal RFI and EMI filter
  • Operational at supply voltages as low as 1.8 V
  • Easier to stabilize with higher capacitive load due to resistive open-loop output impedance
  • Extended temperature range: -40°C to 125°C

TLV9001T Applications

  • Sensor signal conditioning

  • Power modules

  • Active filters

  • Low-side current sensing

  • Smoke detectors

  • Motion detectors

  • Wearable devices

  • Large and small appliances

  • EPOS

  • Barcode scanners

  • Personal electronics

  • HVAC: heating, ventilating, and air conditioning

  • Motor control: AC induction

TLV9001T Pin Configuration

Figure 6-1. TLV9001 DBV, TLV9001T DCK Package 5-Pin SOT-23, SC70 Top View

Figure 6-2. TLV9001 DCK Package, TLV9001 DRL Package, TLV9001U DBV Package 5-Pin SC70, SOT-553, SOT-23 Top View

Figure 6-1. TLV9001 DBV, TLV9001T DCK Package 5-Pin SOT-23, SC70 Top View

Figure 6-3. TLV9001 DPW Package 5-Pin X2SON Top View

Table 6-1. Pin Functions: TLV9001

PIN - NAMEPIN - SOT-23, SC70(T)PIN - SC70, SOT-23(U), SOT-553PIN - X2SONI/ODESCRIPTION
IN-432IInverting input
IN+314INoninverting input
OUT141OOutput
V-223I or-Negative (low) supply or ground (for single-supply operation)
V+555IPositive (high) supply

Figure 6-4. TLV9001S DBV Package 6-Pin SOT-23 Top View

Table 6-1. Pin Functions: TLV9001

Figure 6-5. TLV9001S DCK Package 6-Pin SC70 Top View

Table 6-2. Pin Functions: TLV9001S

PIN - NAMEPIN - SOT-23PIN - SC70I/ODESCRIPTION
IN-43IInverting input
IN+31INoninverting input
OUT14OOutput
SHDN55IShutdown: low = amp disabled, high = amp enabled. See Section 8.5 for more information.
V-22I or-Negative (low) supply or ground (for single-supply operation)
V+66IPositive (high) supply

Figure 6-6. TLV9002 D, DGK, PW, DDF Package 8-Pin SOIC, VSSOP, TSSOP, SOT-23 Top View

Table 6-2. Pin Functions: TLV9001S

A. Connect thermal pad to V-.

Figure 6-7. TLV9002 DSG Package 8-Pin WSON With Exposed Thermal Pad Top View

Table 6-3. Pin Functions: TLV9002

PINPINI/O
NAMENO.I/ODESCRIPTION
IN1-2IInverting input, channel 1
IN1+3INoninverting input, channel 1
IN2-6IInverting input, channel 2
IN2+5INoninverting input, channel 2
OUT11OOutput, channel 1
OUT27OOutput, channel 2
V-4I or-Negative (low) supply or ground (for single-supply operation)
V+8IPositive (high) supply

Table 6-3. Pin Functions: TLV9002

Figure 6-8. TLV9002S DGS Package 10-Pin VSSOP Top View

Figure 6-9. TLV9002S RUG Package 10-Pin X2QFN Top View

Not to scale

Figure 6-10. TLV9002S YCK Package 9-Pin DSBGA (WCSP) Bottom View

TLV9001T Electrical Characteristics

For VS = (V+) - (V-) = 1.8 V to 5.5 V (±0.9 V to ±2.75 V), T A = 25°C, R L = 10 kΩ connected to VS / 2, and VCM = VOUT = VS / 2 (unless otherwise noted)

PARAMETERTEST CONDITIONSMINTYPMAXUNIT
OFFSET VOLTAGEOFFSET VOLTAGE
VV S = 5 V±0.4±1.6
OSInput offset voltageV S = 5 V, T A = -40°C to 125°C±2mV
dV OS /dTV OS vs temperatureT A = -40°C to 125°C±0.6μV/°C
PSRRPower-supply rejection ratioV S = 1.8 to 5.5 V, V CM = (V-)80105dB
INPUT VOLTAGE RANGEINPUT VOLTAGE RANGE
V CMCommon-mode voltage rangeNo phase reversal, rail-to-rail input
V S = 1.8 V, (V-) - 0.1 V < V CM < (V+) - 1.4 V, T A = -40°C to 125°C		(V-) - 0.186(V+) + 0.1V
CMRRCommon-mode rejection ratioV S = 5.5 V, (V-) - 0.1 V < V CM < (V+) - 1.4 V, T A = -40°C to 125°C
V S = 5.5 V, (V-) - 0.1 V < V CM < (V+) + 0.1 V, T A = -40°C to 125°C
V S = 1.8 V, (V-) - 0.1 V < V CM < (V+) + 0.1 V, T A = -40°C to 125°C		6395
77
68		dB
INPUT BIAS CURRENTINPUT BIAS CURRENT
I BInput bias currentV S = 5 V±5pA
I OSInput offset current±2pA
NOISENOISE
E nInput voltage noise (peak-to- peak)ƒ = 0.1 Hz to 10 Hz, V S = 5 V
ƒ = 1 kHz, V S = 5 V		4.7
30		μV PP
nV/√ Hz
e nInput voltage noise densityƒ = 10 kHz, V S = 5 V27
i nInput current noise densityƒ = 1 kHz, V S = 5 V23fA/√ Hz
INPUT CAPACITANCEINPUT CAPACITANCE
C IDDifferential1.5pF
C ICCommon-mode5pF
OPEN-LOOP GAINOPEN-LOOP GAIN
V S = 5.5 V, (V-) + 0.05 V < V O < (V+) - 0.05 V, R L = 10 kΩ
V S = 1.8 V, (V-) + 0.04 V < V O < (V+) - 0.04 V, R L = 10 kΩ		104117
100		dB
dB
A OLOpen-loop voltage gainV S = 1.8 V, (V-) + 0.1 V < V O < (V+) - 0.1 V, R L = 2 kΩ
V S = 5.5 V, (V-) + 0.15 V < V O < (V+) - 0.15 V, R L = 2 kΩ		115
130		dB
dB
FREQUENCY RESPONSEFREQUENCY RESPONSE
GBWGain-bandwidth productV S = 5 V1MHz
φ mPhase marginV S = 5.5 V, G = 178°
SRSlew rateV S = 5 V
To 0.1%, V S = 5 V, 2-V step, G = +1, C L = 100 pF		2
2.5		V/μs
t SSettling timeTo 0.01%, V S = 5 V, 2-V step, G = +1, C L = 100 pF3μs
t OROverload recovery timeV S = 5 V, V IN × gain > V S0.85μs
THD+NTotal harmonic distortion + noiseV S = 5.5 V, V CM = 2.5 V, V O = 1 V RMS , G = +1, ƒ = 1 kHz, 80-kHz measurement BW0.004%
OUTPUTOUTPUT
VVoltage output swing fromV S = 5.5 V, R L = 10 kΩ1020mV
Osupply railsV S = 5.5 V, R L = 2 kΩ3555
I SCShort-circuit currentV S = 5.5 V±40mA
Z OOpen-loop output impedanceV S = 5 V, ƒ = 1 MHz1200Ω

TLV9001T Absolute Maximum Ratings

over operating temperature range (unless otherwise noted) (1)

MINMAXUNIT
Supply voltage (V+) - (V-)Supply voltage (V+) - (V-)Supply voltage (V+) - (V-)7V
Signal input pinsCommon-mode(V-) - 0.5(V+) + 0.5V
Signal input pinsDifferential(V+) - (V-) + 0.2(V+) - (V-) + 0.2V
Signal input pinsCurrent (2)Current (2)-1010mA
Output short-circuit (3)Output short-circuit (3)Output short-circuit (3)ContinuousContinuousContinuous
Operating, T AOperating, T AOperating, T A-55150°C
Junction, T JJunction, T JJunction, T J150°C
Storage, T stgStorage, T stgStorage, T stg-65150°C

TLV9001T Recommended Operating Conditions

over operating temperature range (unless otherwise noted)

MINMAXUNIT
V SSupply voltage1.85.5V
T ASpecified temperature-40125°C

TLV9001T Thermal Information

TLV9001T Typical Application

The TLV900x family of low-power, rail-to-rail input and output operational amplifiers is specifically designed for portable applications. The devices operate from 1.8 V to 5.5 V, are unity-gain stable, and are suitable for a wide range of general-purpose applications. The class AB output stage is capable of driving less than or equal to 10 -kΩ loads connected to any point between V+ and V-. The input common-mode voltage range includes both rails, and allows the TLV900x devices to be used in any single-supply application.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
TLV9001Texas Instruments—
TLV9001IDBVRTexas InstrumentsSOT-23 (5)
TLV9001IDCKRTexas InstrumentsSC70-5
TLV9001IDPWRTexas InstrumentsX2SON-5
TLV9001STexas Instruments—
TLV9001SIDCKTexas InstrumentsSC70-6
TLV9001UTexas InstrumentsSOT-23-5
TLV9002Texas Instruments—
TLV9002STexas Instruments—
TLV9004Texas Instruments—
TLV9004STexas InstrumentsWQFN-16 3.00x3.00mm

Other Operational Amplifiers

  • LM358 – onsemi, Dual Operational Amplifier
  • NE5532 – Texas Instruments, Dual Operational Amplifier
  • AD623A – Analog Devices, Rail-to-Rail Instrumentation Amplifier
  • AD623ARMZ-REEL7 – Analog Devices, Rail-to-Rail Instrumentation Amplifier
  • AD623ARZ – Analog Devices, Rail-to-Rail Instrumentation Amplifier
  • AD623ARZ-RL – Analog Devices, Rail-to-Rail Instrumentation Amplifier
  • AD623B – Analog Devices, Rail-to-Rail Instrumentation Amplifier
  • AD623BNZ – Analog Devices, Rail-to-Rail Instrumentation Amplifier

All Operational Amplifiers datasheetsAll Texas Instruments datasheets (2,418)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TLV9001T

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TLV9001T run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.