SY6970QCC
Synchronous Buck ChargerThe SY6970QCC is a synchronous buck charger from Silergy Corp.. View the full SY6970QCC datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
SY6970QCC shares its datasheet with SY6970, whose page lists every part number it covers.
Official SY6970QCC datasheet (PDF) — the source this page was extracted from.
SY6970QCC Key Specifications
| Parameter | Value |
|---|---|
| BUS operating range | 3.9–14 V; BUS over-voltage rising threshold 14.3 V (typ) |
| Input current limit range | 100–3250 mA (I²C programmable) |
| USB input current limits | USB100 ≤100 mA, USB500 ≤500 mA, USB900 ≤900 mA |
| Battery discharge current (no BUS, VBAT = 4.2 V) | 5 µA typ |
| BUS supply current in High-Z mode | 15 µA typ (VBUS = 5 V); 25 µA typ (VBUS = 12 V) |
| BUS supply current, converter not switching | 1.5 mA typ, 3 mA max |
| BATFET discharge over-current threshold | 9 A |
| Battery over-voltage threshold | 104% of VBAT_REG (typ) |
SY6970QCC Overview
Part: SY6970QCC — Silergy Corp.
Type: Single-Cell Li-Ion/Li-Polymer Switching Battery Charger with Power Path Management
Description: 3.9–14 V input, 5 A, 1.5 MHz buck battery charger with I²C control, USB BC1.2 detection, JEITA compliance and up to 2.4 A boost OTG output, in a QFN4x4-24 package.
Operating Conditions:
- Supply voltage (BUS): 3.9–14 V operating range (recommended BUS/PMID/LX: 0 to 16 V; other pins: 0 to 5.5 V)
- Operating temperature: -40 to 85 °C ambient
- Junction temperature: -40 to 125 °C (recommended)
- Charge voltage adjustable 3.84–4.608 V; OTG output voltage 4.55–5.51 V
Absolute Maximum Ratings:
- BUS, PMID, LX: -0.3 V to +18 V
- Other pins: -0.3 V to +6 V
- Junction temperature: -40 to +150 °C
- Storage temperature: -65 to +150 °C
- Lead temperature (soldering, 10 s): +300 °C
- ESD: HBM 2 kV, MM 200 V
Key Specs:
- BUS operating range: 3.9–14 V; BUS over-voltage rising threshold 14.3 V (typ)
- Charge voltage regulation ±0.5%; charge current regulation ±7%
- Input current limit range: 100–3250 mA (I²C programmable)
- USB input current limits: USB100 ≤100 mA, USB500 ≤500 mA, USB900 ≤900 mA
- Battery discharge current (no BUS, VBAT = 4.2 V): 5 µA typ
- BUS supply current in High-Z mode: 15 µA typ (VBUS = 5 V); 25 µA typ (VBUS = 12 V)
- BUS supply current, converter not switching: 1.5 mA typ, 3 mA max
- BATFET discharge over-current threshold: 9 A
- Thermal regulation 120 °C (typ, TREG bits = 11); thermal shutdown 160 °C with 30 °C hysteresis
- Battery over-voltage threshold: 104% of VBAT_REG (typ)
Features:
- 5 A, 1.5 MHz buck mode charger with narrow VDC power path management
- Programmable IDPM/VDPM for USB and adapter inputs
- USB SDP/DCP/CDP and non-standard adapter detection (BC1.2)
- JEITA compliance
- Battery path impedance compensation to accelerate charging
- Boost OTG mode with up to 2.4 A current limit, 500 kHz/1.5 MHz, ±1% regulation
- Battery monitor for voltage, temperature and charge current
- Full BATFET control supporting shipping mode, wake-up and system reset
- Safety: NTC sensing, charging safety timer, thermal regulation and shutdown, input/system OVP, MOSFET OCP
- Low battery leakage current and shipping mode support
- STAT and INT outputs for status and fault reporting
Applications:
- Smart phone
- Tablet PC
- Power bank
- Portable internet devices
Package:
- QFN4x4-24
SY6970QCC Features
- High Efficiency 5A 1.5MHz Buck Mode Charger
- -Support 3.9V-14V Input Voltage Range
- -Programmable IDPM/VDPM to Support the USB and Adapter
- -Support USB SDP/DCP/CDP and NonStandard Adapter Detection
- -3.84-4.608V Adjustable Charge Voltage
- -Support Narrow VDC Power Path Management
- -JEITA Compliance
- -±0.5% Charge Voltage Regulation
- -±7% Charge Current Regulation
- -Accelerate Charge Time by Battery Path Impedance Compensation.
- -Charge Status Outputs for LED or Host Processor
- Maximum 2.4A 500KHz/1.5MHz Boost OTG Current
- -4.55-5.51V Adjustable OTG Output Voltage
- -Selectable OTG Output Current Limit
- -Up to 2.4A OTG Current Limit on BUS
- -± 1% Output Regulation in Boost Mode
- Battery Monitor for Voltage, Temperature and Charge Current Measurements
- Full BATFET Control to Support Shipping Mode, Wake Up, and System Reset
- Up to 9A Battery Discharge Current
- Safety
- -Battery Temperature Sensing for Charge and Boost Mode
- -Battery Charging Safety Timer
- -Thermal Regulation and Thermal Shutdown
- -Input/System Over-voltage Protection
- -MOSFET Over-current Protection
- Low Battery Leakage Current and Support Shipping Mode
- 4mm x 4mm QFN-24 Package
SY6970QCC Applications
- Smart Phone
- Tablet PC
- Power Bank
- Portable Internet Devices
SY6970QCC Pin Configuration
| Pin Name | Pin Number | Pin Description |
|---|---|---|
| BUS | 1 | Charger power input pin. Connect a 1μF ceramic capacitor from BUS to PGND as close as possible to the IC. |
| DP | 2 | USB identification port. USB detection strategy is compliant with BC1.2. SDP, CDP, DCP and adapter port can be identified according to the detection results thru DP/DM pins. |
| DM | 3 | USB identification port. USB detection strategy is compliant with BC1.2. SDP, CDP, DCP and adapter port can be identified according to the detection results thru DP/DM pins. |
| STAT | 4 | Open drain charge status indication pin. Pull up to a logic rail via 10kΩ resistor. STAT pin low indicates charge in progress; high indicates charge done or charge disabled. When any charge fault occurs, STAT pin blinks at 1Hz. The stat pin function can be disabled by setting STAT_DIS bit. |
| SCL | 5 | I 2 C Interface clock pin. Pull up to a logic rail via 10kΩ resistor. |
| SDA | 6 | I 2 C Interface data pin. Pull up to a logic rail via 10kΩ resistor. |
| INT | 7 | Open-drain Interrupt Output. Pull up to a logic rail via 10kΩ resistor. The INT pin generates active low, 256us pulse to notify the host about charge status and charge fault. |
| OTG | 8 | Boost mode active high enable pin. Boost mode is enabled when REG03[5]=1 and OTG pin is high. |
| /CE | 9 | Charge mode active low enable pin. Battery charging is enabled when REG03[4]=1 and /CE pin =Low. /CE pin must be pulled high or low. |
| ILIM | 10 | ILIM pin sets the maximum input current limit. A resistor is connected from ILIM pin to ground to set the maximum limit as I INMAX = K ILIM /R ILIM . The actual input current limit is the lower one set by ILIM and by I 2 C REG00[5:0]. The ILIM pin function can be disabled by setting EN_ILIM bit to 0 |
| NTC | 11 | Connect a resistor divider from REGN to NTC to GND to achieve battery |
© 2019 Silergy Corp. All Rights Reserved.
| thermal protection. Charge or discharge suspends when NTC pin is out of range. Recommend 103AT-2 thermistor. | ||
|---|---|---|
| /QON | 12 | BATFET enables control in shipping mode and BATFET reset function. When BATFET is in shipping mode, logic high to low transition on this pin with minimum of T QON_1 low level turns on BATFET to exit shipping mode. This pin is internally pulled up to maintain default high logic. When BUS is not plugged-in, a logic low of T QON_RST (typical 10s) resets system power by turning BATFET off for T BATFET_RST (typical 3s) and then re- enable BATFET. |
| BAT | 13,14 | Battery voltage sense pin. Used as battery constant voltage control and battery voltage protections. Connect at least 10μF ceramic capacitor to the BAT pin. |
| SYS | 15,16 | System connection point. The internal BATFET is connected between BAT and SYS. When the battery falls below the minimum system voltages, switch-mode converter will keep SYS above the minimum system voltage. |
| PGND | 17,18 | Power ground connection. On PCB layout, connect this pin directly to ground connection of input and output capacitors. |
| LX | 19,20 | Switching node pin. Connect this pin to external inductor. |
| BST | 21 | HSFET driver positive supply. Connect a 47nF bootstrap capacitor between LX and BST. |
| REGN | 22 | LSFET driver positive supply. Connect a 4.7μF ceramic capacitor between REGN and analog GND. The capacitor should be placed closely to the IC. REGN also serves as bias rail of NTC pin. |
| PMID | 23 | Connect this pin to the drain of the reverse blocking MOSFET and the drain of HSFET. Connect a 6.8μ F capacitor between PMID and PGND. The capacitor should be placed closely to the IC. |
| DSEL | 24 | Open-drain DP/DM multiplexer selection control. Pull up to a logic rail via 10kΩ resistor. During input source type detection, the pin outputs low to indicate DP/DM detection is in progress. When detection is done, the pin keeps low if HVDCP is detected. The pin returns to float and pulls high by resistor when other input source type is detected. |
| Exposed pad | - | Exposed pad beneath the IC for heat dissipation. Always solder exposed pad to the board, and have vias on the power pad plane star-connecting to PGND and ground plane for high-current power converter. |
© 2019 Silergy Corp. All Rights Reserved.
SY6970QCC Electrical Characteristics
(VBUS_UVLOZ<VBUSVBAT+VSLEEP, TA=25° C for typical values unless other noted.)
| Parameter | Symbol | Test Conditions | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS |
| Battery Discharge Current (BAT) | I BAT | V BUS <V BUS_UVLOZ , V BAT =4.2 V, leakage between BAT and BUS | 5 | μA | ||
| Battery Discharge Current (BAT) | High-Z Mode, no BUS, battery monitor disabled, BATFET disabled, T J <85° C | 12 | μA | |||
| Battery Discharge Current (BAT) | High-Z Mode, no BUS, battery monitor disabled, BATFT enabled, T J =-40° C to 85° C | 32 | μA | |||
| Input Supply Current in High-Z Mode | I BUS_HIZ | V BUS =5V, battery monitor disabled, no battery, High-Z mode enabled | 15 | μA | ||
| Input Supply Current in High-Z Mode | V BUS =12V, battery monitor disabled, no battery, High-Z mode enabled | 25 | μA | |||
| Input Supply Current (BUS) | I BUS | V BUS >V BUS_UVLOZ , V BUS >V BAT , converter not switching | 1.5 | 3 | mA | |
| Input Supply Current (BUS) | I BUS | V BUS >V BUS_UVLOZ , V BUS >V BAT, converter switching, V BAT =3.2V, I SYS =0A | 3 | mA | ||
| Input Supply Current (BUS) | V BUS >V BUS_UVLOZ , V BUS >V BAT , converter switching, charge disabled,V BAT =3.8V, I SYS =0A | 3 | mA | |||
| Battery Discharge Current in Boost Mode | I OTGBOOST | V BAT =4.2V, Boost mode, I BUS =0A, converter switching | 3.5 | mA | ||
| BUS/BATPOWERUP | BUS/BATPOWERUP | BUS/BATPOWERUP | BUS/BATPOWERUP | BUS/BATPOWERUP | BUS/BATPOWERUP | BUS/BATPOWERUP |
| BUS Operating Range | V BUS_OP | 3.9 | 14 | V | ||
| BUS for Active IC and I 2 C, No Battery | V BUS_UVLOZ | V BUS rising | 3.6 | V | ||
| Sleep Mode Falling Threshold | V SLEEP | V BUS falling,V BUS -V BAT | 65 | mV | ||
| Sleep Mode Rising Threshold | V SLEEPZ | V BUS rising,V BUS -V BAT | 250 | mV | ||
| BUS Over-voltage Rising Threshold | V ACOV | V BUS rising | 14.3 | V | ||
| BUS Over-voltage Recovery Threshold | V ACOV_RC | V BUS falling | 300 | mV | ||
| Battery Depletion Threshold | V BAT_DPL | V BAT falling V rising | 2.3 2.5 | V | ||
| Battery Depletion Recovery Threshold | V BAT_DPLZ | BAT | V |
© 2019 Silergy Corp. All Rights Reserved.
© 2019 Silergy Corp. All Rights Reserved.
SY6970QCC Absolute Maximum Ratings
- Others ------------------------------------------------------------------------------------------------------------ -0.3V to +6V
- Package Thermal Resistance (Notes 2) QFN4x4-24 θ JA ----------------------------------------------------------------------------------------- 33.3° C/W QFN4x4-24 θ JC ----------------------------------------------------------------------------------------- 29.7° C/W
- Junction Temperature Range ----------------------------------------------------------------------------- -40° C to C Operating Temperature Range --------------------------------------------------------------------------- -40° C to +100°
- +150° C
- Storage Temperature -------------------------------------------------------------------------------------- -65° C to +150°
- C Lead Temperature (Soldering, 10s) -------------------------------------------------------------------------------- +300° C
- ESD Susceptibility HBM(Human Body Mode) ---------------------------------------------------------------------------------------------
- 2kV MM(Machine Mode) --------------------------------------------------------------------------------------------------- 200V
- Recommended Operating Conditions (Note 3)
- BUS, PMID, LX ------------------------------------------------------------------------------------------------- 0V to +16V Others ------------------------------------------------------------------------------------------------------------- 0V to
- +5.5V
- Junction Temperature Range ------------------------------------------------------------------------------ -40° C to 125° C
- Temperature Range ------------------------------------------------------------------------------- -40° C to 85° C
- Ambient
© 2019 Silergy Corp. All Rights Reserved.
SY6970QCC Thermal Information
The SY6970 monitors the internal junction temperature TJ to avoid overheat the chip and limits the IC surface temperature. When the internal junction temperature exceeds the preset limit (TREG bits), the device will lower down the charge current. The wide thermal regulation range from 60° C to 120° C allows the user to optimize the system thermal performance.
During thermal regulation, the actual charging current is usually below the programmed battery charging current. Therefore, termination is disabled, the safety timer runs at half the clock rate, and the status register THERM_STAT goes high.
Additionally, the device has thermal shutdown to turn off the converter and BATFET. The fault register CHRG_FAULT is 10 and an INT is asserted to the host. The BATFET and converter are enabled to recover when the IC temperature is below TTSD_HYS.
SY6970QCC Typical Application
© 2019 Silergy Corp. All Rights Reserved.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| SY6970 | Silergy Corp. | QFN-24 4x4mm |
Other Battery Chargers
- SLM6305 – SOLA IC, Li-ion Battery Charger / Synchronous Buck Converter
- NPM1300-QEAA-R7 – Nordic Semiconductor, Battery Charger Power Management IC
- MP2639BGR-Z – Monolithic Power Systems, 1S Li-ion Switching Charger with OTG
- BQ24075 – Texas Instruments, Standalone 1-Cell 1.5-A Linear Battery Chargers with Power Path
- BQ24075-Q1 – Texas Instruments, Standalone 1-Cell 1.5-A Linear Battery Chargers with Power Path
- BQ24075RGTR – Texas Instruments, Standalone 1-Cell 1.5-A Linear Battery Chargers with Power Path
- BQ24075RGTR.A – Texas Instruments, Standalone 1-Cell 1.5-A Linear Battery Chargers with Power Path
- BQ24075RGTR.B – Texas Instruments, Standalone 1-Cell 1.5-A Linear Battery Chargers with Power Path
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.
Ask your AI agent about the SY6970QCC
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the SY6970QCC run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.