Part: VN750-E — STMicroelectronics

Type: High-side driver

Description: Monolithic high-side driver designed in VIPower M0-3 technology for driving loads connected to ground, featuring 60 mΩ on-state resistance, 6 A output current, and 36 V supply voltage.

Operating Conditions:

• Supply voltage: 5.5–36 V
• Operating temperature: -40 to 150 °C

Absolute Maximum Ratings:

• Max reverse DC output current: -6 A
• Max storage temperature: -55 to 150 °C

Key Specs:

• On-state resistance (R_ON): 60 mΩ (I_OUT=2 A; T_j=25 °C; V_CC > 8 V)
• Supply current (I_S, off-state): 10 μA (V_CC=13 V; V_IN=V_OUT=0 V; T_j=25 °C)
• Turn-on delay time (t_d(on)): 40 μs (R_L=6.5 Ω)
• Turn-off delay time (t_d(off)): 30 μs (R_L=6.5 Ω)
• Input low level (V_IL): 1.25 V
• Input high level (V_IH): 3.25 V
• Shutdown temperature (T_TSD): 150 °C (Min)
• Current limitation (I_lim): 6 A (9 V < V_CC < 36 V)

Features:

• ECOPACK®: lead free and RoHS compliant
• Automotive Grade: compliance with AEC guidelines
• CMOS compatible input
• On-state open-load detection
• Off-state open-load detection
• Shorted load protection
• Undervoltage and overvoltage shutdown
• Protection against loss of ground
• Very low standby current
• Reverse battery protection

Applications:

• Driving any kind of load with one side connected to ground

Package:

• PENTAWATT
• P 2 PAK
• PPAK
• PENTAWATT in-line

• ■ ECOPACK ® : lead free and RoHS compliant
• ■ Automotive Grade: compliance with AEC guidelines
• ■ CMOS compatible input
• ■ On-state open-load detection
• ■ Off-state open-load detection
• ■ Shorted load protection
• ■ Undervoltage and overvoltage shutdown
• ■ Protection against loss of ground
• ■ Very low standby current
• ■ Reverse battery protection

Table 1. Device summary

VN750PTTR-E Pinout

Package: TO-252-5 (DPAK, 4 Leads + Tab)

Notes

• Pin 5 (STATUS): Provides diagnostic information including overvoltage detection, undervoltage detection, overtemperature detection, on-state/open-load detection, and off-state/output-shorted-to-VCC detection.
• Tab (GND): The exposed thermal tab on the back of the DPAK package is electrically connected to GND (pin 1) and should be soldered to a ground plane for thermal management.
• Unused pins: Per Table 2, floating pins are acceptable for N.C. pins; outputs should float or connect to ground; inputs should connect to ground through a 10 kΩ resistor.

Figure 3. Current and voltage conventions

Stress values that exceed those listed in the 'Absolute maximum ratings' table can cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions greater than those, indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics sure program and other relevant quality documents.

Table 3. Absolute maximum ratings

Table 3. Absolute maximum ratings

Table 3. Absolute maximum ratings (continued)

Table 4. Thermal data

Figure 35. PENTAWATT package dimensions

Table 12. PENTAWATT mechanical data

Table 12. PENTAWATT mechanical data

Table 12. PENTAWATT mechanical data (continued)

Table 12. PENTAWATT mechanical data (continued)