Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

TPS22917DBVT

Load Switch

The TPS22917DBVT is a load switch from Texas Instruments. View the full TPS22917DBVT datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

TPS22917DBVT shares its datasheet with TPS22917, whose page lists every part number it covers.

Official TPS22917DBVT datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Load Switch

Package

SOT-23-6

Lifecycle

Production (Last Updated: 1 day ago)

TPS22917DBVT Key Specifications

ParameterValue
Case/PackageSOT-23
Control Input LogicActive High
Current - Output (Max)2A
Fall Time22 µs
Fault ProtectionReverse Current
FeaturesLoad Discharge, Slew Rate Controlled
FeaturesSoft-start;Output discharge function;Reverse current blocking
Height0 m
Input TypeNon-Inverting
InterfaceOn/Off
Length2.9 mm
Lifecycle StatusProduction (Last Updated: 1 day ago)
Manufacturer Lifecycle StatusACTIVE (Last Updated: 1 day ago)
Max Junction Temperature (Tj)125 °C
Max Operating Temperature125 °C
Max Supply Voltage5.5 V
Maximum Continuous Current2A
Min Operating Temperature-40 °C
Min Supply Voltage1 V
Mounting TypeSurface Mount
Nominal Input Voltage5.5 V
Nominal Supply Current500 nA
number of channels1
Number of Channels1
Number of Drivers1
Number of Outputs1
Number of Outputs1
Number of Pins6
Operating Temperature-40℃~+125℃ °C
Operating Temperature-40°C ~ 125°C
Operating Voltage1V~5.5V
Output ConfigurationHigh Side
Output Current2 A
Output TypeP-Channel
Output Voltage5.5 V
Package / CaseSOT-23-6
PackagingCut Tape
PackagingMouseReel
Ratio - Input:Output1:1
Rds On (Typ)80mOhm
RDS(on)80mΩ
Rise Time55 µs
RoHSCompliant
Schedule B8542390000, 8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|85
Standard Pack Qty250
Supplier Device PackageSOT-23-6
Switch TypePower Switch
Thickness1.2 mm
Turn-Off Delay Time10 µs
Turn-On Delay Time100 µs
TypeLoad Switch
Load Voltage0V ~ 5.5V
Supply Voltage1V ~ 5.5V
Width1.6 mm

TPS22917DBVT Overview

Part: TPS22917DBVT — Texas Instruments (TPS22917x family)

Type: Load Switch (single-channel, P-channel MOSFET, ultra-low leakage)

Description: 1–5.5 V input, 2 A load switch with 80 mΩ typical on-resistance at 5 V, 0.5 μA typical quiescent current, adjustable turn-on slew rate, and always-on reverse current blocking.

Operating Conditions:

  • Supply voltage (VIN): 1 to 5.5 V
  • Operating temperature: -40 to 125 °C
  • ON pin: VIH 1 to 5.5 V, VIL 0 to 0.35 V
  • Output voltage (VOUT): 0 to 5.5 V

Absolute Maximum Ratings:

  • Max input voltage (VIN): 6 V
  • Max continuous switch current: 2 A
  • Max pulsed switch current: 2.5 A (pulse < 300 μs, 2% duty cycle)
  • Max junction temperature: 125 °C
  • Storage temperature: -65 to 150 °C

Key Specs:

  • On-resistance (IOUT = 200 mA, 25 °C typ): 80 mΩ at VIN = 5 V, 120 mΩ at 3.6 V, 220 mΩ at 1.0 V
  • On-resistance at 5 V, max: 100 mΩ at 25 °C (160 mΩ over -40 to +125 °C)
  • Quiescent current (enabled, VOUT open): 0.5 μA typ, 1.0 μA max (-40 to +85 °C), 1.2 μA max (-40 to +125 °C)
  • Shutdown current (TPS22917, VOUT = GND): 10 nA typ, 100 nA max (-40 to +85 °C)
  • ON pin leakage (TPS22917): ±10 nA max
  • Smart pulldown resistance (VON ≤ VIL): 750 kΩ
  • Reverse current blocking activation: -0.5 A typ; reverse leakage (IIN,RCB) -1 μA max
  • Turn-on time at VIN = 5 V: 100 μs typ (CT open); turn-on slew rate 72 mV/μs (CT open)
  • Quick output discharge resistance: 150 Ω min (internal)
  • Thermal resistance θJA: 183 °C/W (SOT-23)

Features:

  • Smart ON pin pulldown disconnects after ON is driven high
  • Adjustable turn-on time via CT capacitor to limit inrush current
  • Adjustable output discharge and fall time via QOD pin
  • Always-on true reverse current blocking
  • Leaded SOT-23 package allows visual solder joint inspection
  • TPS22917 active-high enable; TPS22917L active-low enable
  • ESD: HBM ±2000 V, CDM ±500 V

Applications:

  • Industrial systems
  • Set top box
  • Blood glucose meters
  • Electronic point of sale

Package:

  • SOT-23 (DBV), 6 pins, 2.90 mm × 1.60 mm

TPS22917DBVT Features

  • Input operating voltage range (VIN ): 1 V to 5.5 V
  • Maximum continuous current (IMAX): 2 A
  • On-resistance (RON):
  • -5 VIN = 80 mΩ (typical)
  • -1.8 VIN = 120 mΩ (typical)
  • -1 VIN = 220 mΩ (typical)
  • Ultra-low power consumption:
  • -ON state (I Q ): 0.5 μA (typical)
  • Smart ON pin pulldown (RPD):
  • -OFF state (I SD ): 10 nA (typical)
  • -ON ≥ VIH (ION): 10 nA (maximum)
  • -ON ≤ VIL (RPD): 750 kΩ (typical)
  • Adjustable turn ON limits inrush current (t ON):
  • -5-V tON = 100 μs at 72 mV/μs (CT = open)
  • -5-V tON = 4000 μs at 2.3 mV/μs (CT = 1000 pF)
  • Adjustable output discharge and fall time:
  • -Optional QOD resistance ≥ 150 Ω (internal)
  • Always-ON true Reverse Current Blocking (RCB):
  • -Activation current (I RCB): -500 mA (typical)
  • -Reverse leakage (IIN,RCB): -1 μA (maximum)

TPS22917DBVT Applications

  • Industrial systems
  • Set top box
  • Blood glucose meters
  • Electronic point of sale

TPS22917DBVT Pin Configuration

Figure 6-1. DBV Package 6-Pin SOT-23 Top View

Table 6-1. Pin Functions

PIN - NO.PIN - NAMEI/ODESCRIPTION
1VINISwitch input
2GND-Device ground
3ONIActive high switch control input. Do not leave floating.
4CTOSwitch slew rate control. Connect capacitor from this pin to VIN to increase output slew rate and turn-on time. Can be left floating for fastest timing.
5QODOQuick Output Discharge pin. This functionality can be enabled in one of three ways. • Placing an external resistor between VOUT and QOD • Tying QOD directly to VOUT and using the internal resistor value (R PD ) • Disabling QOD by leaving pin floating See the Fall Time (t FALL ) and Quick Output Discharge (QOD) section for more information.
6VOUTOSwitch output

Table 6-1. Pin Functions

TPS22917DBVT Electrical Characteristics

Unless otherwise noted, the specification in the following table applies for all variants over the entire recommended power supply voltage range of 1 V to 5.5 V. Typical Values are at 25°C.

PARAMETERPARAMETERTEST CONDITIONST JMIN TYPMAXUNIT
INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)INPUT SUPPLY(VIN)
I Q,VINV IN Quiescent current-40°C to +85°C0.51.0μA
I Q,VINV IN Quiescent currentEnabled, V OUT = Open-40°C to +125°C1.2μA
I SD,VINV IN Shutdown current-40°C to +85°C10100nA
I SD,VINV IN Shutdown currentDisabled, V OUT = GND (TPS22917)-40°C to +105°C250nA
I SD,VINV IN Shutdown current-40°C to +85°C175300nA
I SD,VINV IN Shutdown currentDisabled, V OUT = GND (TPS22917L)-40°C to +105°C400nA
ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )ON-RESISTANCE(R ON )
ON-ResistanceV IN = 5 V
V IN = 3.6 V
25°C -40°C to +125°C -40°C to +125°C
-40°C to +85°C
-40°C to +105°C
-40°C to +125°C
25°C
-40°C to +85°C
-40°C to +105°C
25°C
-40°C to +85°C
80
90
120
100 160 200
120
130
140
110
140
150
150
175
R ON= 200 mA V IN = 1.8 V
OUT
V IN = 1.2 V
-40°C to +105°C
OUT
25°C
-40°C to +85°C
-40°C to +105°C
-40°C to +125°C
170185
220
265
280
300
mΩ
VIN = 1.0 V25°C -40°C to +85°C
-40°C to +105°C
-40°C to +125°C
220300 350
370
390
ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)ENABLE PIN(ON)
I ONON Pin leakageEnabled (TPS22917)-40°C to +125°C-1010nA
I ONEnabled (TPS22917L)-40°C to +125°C-2020nA
R PDSmart Pull Down ResistanceV ON ≤ V IL-40°C to +105°C750kΩ
REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)REVERSE CURRENT BLOCKING(RCB)
I RCBRCB Activation CurrentEnabled, V OUT > V IN-40°C to +125°C-0.5-1A
t RCBRCB Activation timeEnabled, V OUT > V IN + 200mV-40°C to +125°C10μs
V RCBRCB Release VoltageEnabled, V OUT > V IN-40°C to +125°C25mV
I IN,RCBVIN Reverse Leakage Current0 V ≤ V IN + V RCB ≤ V OUT ≤ 5.5 V-40°C to +105°C-1μA
QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)QUICK OUTPUT DISCHARGE(QOD)
QODOutput discharge resistanceDisabled-40°C to +105°C150Ω

TPS22917DBVT Absolute Maximum Ratings

Over operating free-air temperature range (unless otherwise noted) (1)

MINMAXUNIT
V INInput voltage-0.36V
V OUTOutput voltage-0.36V
V ONEnable voltage-0.36V
V QODQOD pin voltage-0.36V
I MAXMaximum continuous switch current2A
I PLSMaximum pulsed switch current, pulse < 300-μs, 2% duty cycle2.5A
T J,MAXMaximum junction temperature125°C
T STGStorage temperature-65150°C
T LEADMaximum Lead temperature (10-s soldering time)300°C

Over operating free-air temperature range (unless otherwise noted)

MINMAXUNIT
V INInput voltage15.5V
V OUTOutput voltage05.5V
V IHHigh-level input voltage, ON15.5V
V ILLow-level input voltage, ON00.35V
V QODQOD Pin Voltage05.5V
V CTTiming Capacitor Voltage Rating7V

TPS22917DBVT Thermal Information

Thermal Parameters (1)Thermal Parameters (1)TPS22917 DBV (SOT-23) 6 PINSUNIT
θ JAJunction-to-ambient thermal resistance183°C/W
θ JCtopJunction-to-case (top) thermal resistance152°C/W
θ JBJunction-to-board thermal resistance34°C/W
ψ JTJunction-to-top characterization parameter37°C/W
ψ JBJunction-to-board characterization parameter33°C/W

TPS22917DBVT Typical Application

This section highlights some of the design considerations when implementing this device in various applications.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
TPS22917Texas Instruments—
TPS22917DBVRTexas InstrumentsSOT-23-6
TPS22917DBVR.ATexas Instruments—
TPS22917DBVT.ATexas Instruments—
TPS22917LTexas Instruments—
TPS22917LDBVRTexas InstrumentsSOT-23-6
TPS22917LDBVR.ATexas Instruments—

More datasheets

All Texas Instruments datasheets (2,613)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TPS22917DBVT

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TPS22917DBVT run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.