TPS22917DBVR.A
Load SwitchThe TPS22917DBVR.A is a load switch from Texas Instruments. View the full TPS22917DBVR.A datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
TPS22917DBVR.A shares its datasheet with TPS22917, whose page lists every part number it covers.
Official TPS22917DBVR.A datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Load Switch
TPS22917DBVR.A Key Specifications
| Parameter | Value |
|---|---|
| Case/Package | SOT-23 |
| Control Input Logic | Active High |
| Current - Output (Max) | 2A |
| Fall Time | 22 µs |
| Fault Protection | Reverse Current |
| Features | Load Discharge, Slew Rate Controlled |
| Features | Soft-start;Output discharge function;Reverse current blocking |
| Height | 0 m |
| Input Type | Non-Inverting |
| Interface | On/Off |
| Length | 2.9 mm |
| Lifecycle Status | Production (Last Updated: 1 day ago) |
| Manufacturer Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Max Junction Temperature (Tj) | 125 °C |
| Max Operating Temperature | 125 °C |
| Max Supply Voltage | 5.5 V |
| Maximum Continuous Current | 2A |
| Min Operating Temperature | -40 °C |
| Min Supply Voltage | 1 V |
| Mounting Type | Surface Mount |
| Nominal Input Voltage | 5.5 V |
| Nominal Supply Current | 500 nA |
| number of channels | 1 |
| Number of Channels | 1 |
| Number of Drivers | 1 |
| Number of Outputs | 1 |
| Number of Outputs | 1 |
| Number of Pins | 6 |
| Operating Temperature | -40℃~+125℃ °C |
| Operating Temperature | -40°C ~ 125°C |
| Operating Voltage | 1V~5.5V |
| Output Configuration | High Side |
| Output Current | 2 A |
| Output Type | P-Channel |
| Output Voltage | 5.5 V |
| Package / Case | SOT-23-6 |
| Packaging | Cut Tape |
| Packaging | MouseReel |
| Ratio - Input:Output | 1:1 |
| Rds On (Typ) | 80mOhm |
| RDS(on) | 80mΩ |
| Rise Time | 55 µs |
| RoHS | Compliant |
| Schedule B | 8542390000, 8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|85 |
| Standard Pack Qty | 250 |
| Supplier Device Package | SOT-23-6 |
| Switch Type | Power Switch |
| Thickness | 1.2 mm |
| Turn-Off Delay Time | 10 µs |
| Turn-On Delay Time | 100 µs |
| Type | Load Switch |
| Load Voltage | 0V ~ 5.5V |
| Supply Voltage | 1V ~ 5.5V |
| Width | 1.6 mm |
TPS22917DBVR.A Overview
Part: TPS22917DBVT — Texas Instruments (TPS22917x family)
Type: Load Switch (single-channel, P-channel MOSFET, ultra-low leakage)
Description: 1–5.5 V input, 2 A load switch with 80 mΩ typical on-resistance at 5 V, 0.5 μA typical quiescent current, adjustable turn-on slew rate, and always-on reverse current blocking.
Operating Conditions:
- Supply voltage (VIN): 1 to 5.5 V
- Operating temperature: -40 to 125 °C
- ON pin: VIH 1 to 5.5 V, VIL 0 to 0.35 V
- Output voltage (VOUT): 0 to 5.5 V
Absolute Maximum Ratings:
- Max input voltage (VIN): 6 V
- Max continuous switch current: 2 A
- Max pulsed switch current: 2.5 A (pulse < 300 μs, 2% duty cycle)
- Max junction temperature: 125 °C
- Storage temperature: -65 to 150 °C
Key Specs:
- On-resistance (IOUT = 200 mA, 25 °C typ): 80 mΩ at VIN = 5 V, 120 mΩ at 3.6 V, 220 mΩ at 1.0 V
- On-resistance at 5 V, max: 100 mΩ at 25 °C (160 mΩ over -40 to +125 °C)
- Quiescent current (enabled, VOUT open): 0.5 μA typ, 1.0 μA max (-40 to +85 °C), 1.2 μA max (-40 to +125 °C)
- Shutdown current (TPS22917, VOUT = GND): 10 nA typ, 100 nA max (-40 to +85 °C)
- ON pin leakage (TPS22917): ±10 nA max
- Smart pulldown resistance (VON ≤ VIL): 750 kΩ
- Reverse current blocking activation: -0.5 A typ; reverse leakage (IIN,RCB) -1 μA max
- Turn-on time at VIN = 5 V: 100 μs typ (CT open); turn-on slew rate 72 mV/μs (CT open)
- Quick output discharge resistance: 150 Ω min (internal)
- Thermal resistance θJA: 183 °C/W (SOT-23)
Features:
- Smart ON pin pulldown disconnects after ON is driven high
- Adjustable turn-on time via CT capacitor to limit inrush current
- Adjustable output discharge and fall time via QOD pin
- Always-on true reverse current blocking
- Leaded SOT-23 package allows visual solder joint inspection
- TPS22917 active-high enable; TPS22917L active-low enable
- ESD: HBM ±2000 V, CDM ±500 V
Applications:
- Industrial systems
- Set top box
- Blood glucose meters
- Electronic point of sale
Package:
- SOT-23 (DBV), 6 pins, 2.90 mm × 1.60 mm
TPS22917DBVR.A Features
- Input operating voltage range (VIN ): 1 V to 5.5 V
- Maximum continuous current (IMAX): 2 A
- On-resistance (RON):
- -5 VIN = 80 mΩ (typical)
- -1.8 VIN = 120 mΩ (typical)
- -1 VIN = 220 mΩ (typical)
- Ultra-low power consumption:
- -ON state (I Q ): 0.5 μA (typical)
- Smart ON pin pulldown (RPD):
- -OFF state (I SD ): 10 nA (typical)
- -ON ≥ VIH (ION): 10 nA (maximum)
- -ON ≤ VIL (RPD): 750 kΩ (typical)
- Adjustable turn ON limits inrush current (t ON):
- -5-V tON = 100 μs at 72 mV/μs (CT = open)
- -5-V tON = 4000 μs at 2.3 mV/μs (CT = 1000 pF)
- Adjustable output discharge and fall time:
- -Optional QOD resistance ≥ 150 Ω (internal)
- Always-ON true Reverse Current Blocking (RCB):
- -Activation current (I RCB): -500 mA (typical)
- -Reverse leakage (IIN,RCB): -1 μA (maximum)
TPS22917DBVR.A Applications
- Industrial systems
- Set top box
- Blood glucose meters
- Electronic point of sale
TPS22917DBVR.A Pin Configuration
Figure 6-1. DBV Package 6-Pin SOT-23 Top View
Table 6-1. Pin Functions
| PIN - NO. | PIN - NAME | I/O | DESCRIPTION |
|---|---|---|---|
| 1 | VIN | I | Switch input |
| 2 | GND | - | Device ground |
| 3 | ON | I | Active high switch control input. Do not leave floating. |
| 4 | CT | O | Switch slew rate control. Connect capacitor from this pin to VIN to increase output slew rate and turn-on time. Can be left floating for fastest timing. |
| 5 | QOD | O | Quick Output Discharge pin. This functionality can be enabled in one of three ways. • Placing an external resistor between VOUT and QOD • Tying QOD directly to VOUT and using the internal resistor value (R PD ) • Disabling QOD by leaving pin floating See the Fall Time (t FALL ) and Quick Output Discharge (QOD) section for more information. |
| 6 | VOUT | O | Switch output |
Table 6-1. Pin Functions
TPS22917DBVR.A Electrical Characteristics
Unless otherwise noted, the specification in the following table applies for all variants over the entire recommended power supply voltage range of 1 V to 5.5 V. Typical Values are at 25°C.
| PARAMETER | PARAMETER | TEST CONDITIONS | T J | MIN TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|---|
| INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) | INPUT SUPPLY(VIN) |
| I Q,VIN | V IN Quiescent current | -40°C to +85°C | 0.5 | 1.0 | μA | ||
| I Q,VIN | V IN Quiescent current | Enabled, V OUT = Open | -40°C to +125°C | 1.2 | μA | ||
| I SD,VIN | V IN Shutdown current | -40°C to +85°C | 10 | 100 | nA | ||
| I SD,VIN | V IN Shutdown current | Disabled, V OUT = GND (TPS22917) | -40°C to +105°C | 250 | nA | ||
| I SD,VIN | V IN Shutdown current | -40°C to +85°C | 175 | 300 | nA | ||
| I SD,VIN | V IN Shutdown current | Disabled, V OUT = GND (TPS22917L) | -40°C to +105°C | 400 | nA | ||
| ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) | ON-RESISTANCE(R ON ) |
| ON-Resistance | V IN = 5 V V IN = 3.6 V | 25°C -40°C to +125°C -40°C to +125°C -40°C to +85°C -40°C to +105°C -40°C to +125°C 25°C -40°C to +85°C -40°C to +105°C 25°C -40°C to +85°C | 80 90 120 | 100 160 200 120 130 140 110 140 150 150 175 | |||
| R ON | = 200 mA V IN = 1.8 V OUT V IN = 1.2 V | -40°C to +105°C OUT 25°C -40°C to +85°C -40°C to +105°C -40°C to +125°C | 170 | 185 220 265 280 300 | mΩ | ||
| VIN = 1.0 V | 25°C -40°C to +85°C -40°C to +105°C -40°C to +125°C | 220 | 300 350 370 390 | ||||
| ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) | ENABLE PIN(ON) |
| I ON | ON Pin leakage | Enabled (TPS22917) | -40°C to +125°C | -10 | 10 | nA | |
| I ON | Enabled (TPS22917L) | -40°C to +125°C | -20 | 20 | nA | ||
| R PD | Smart Pull Down Resistance | V ON ≤ V IL | -40°C to +105°C | 750 | kΩ | ||
| REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) | REVERSE CURRENT BLOCKING(RCB) |
| I RCB | RCB Activation Current | Enabled, V OUT > V IN | -40°C to +125°C | -0.5 | -1 | A | |
| t RCB | RCB Activation time | Enabled, V OUT > V IN + 200mV | -40°C to +125°C | 10 | μs | ||
| V RCB | RCB Release Voltage | Enabled, V OUT > V IN | -40°C to +125°C | 25 | mV | ||
| I IN,RCB | VIN Reverse Leakage Current | 0 V ≤ V IN + V RCB ≤ V OUT ≤ 5.5 V | -40°C to +105°C | -1 | μA | ||
| QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) | QUICK OUTPUT DISCHARGE(QOD) |
| QOD | Output discharge resistance | Disabled | -40°C to +105°C | 150 | Ω |
TPS22917DBVR.A Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted) (1)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| V IN | Input voltage | -0.3 | 6 | V |
| V OUT | Output voltage | -0.3 | 6 | V |
| V ON | Enable voltage | -0.3 | 6 | V |
| V QOD | QOD pin voltage | -0.3 | 6 | V |
| I MAX | Maximum continuous switch current | 2 | A | |
| I PLS | Maximum pulsed switch current, pulse < 300-μs, 2% duty cycle | 2.5 | A | |
| T J,MAX | Maximum junction temperature | 125 | °C | |
| T STG | Storage temperature | -65 | 150 | °C |
| T LEAD | Maximum Lead temperature (10-s soldering time) | 300 | °C |
TPS22917DBVR.A Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| V IN | Input voltage | 1 | 5.5 | V |
| V OUT | Output voltage | 0 | 5.5 | V |
| V IH | High-level input voltage, ON | 1 | 5.5 | V |
| V IL | Low-level input voltage, ON | 0 | 0.35 | V |
| V QOD | QOD Pin Voltage | 0 | 5.5 | V |
| V CT | Timing Capacitor Voltage Rating | 7 | V |
TPS22917DBVR.A Thermal Information
| Thermal Parameters (1) | Thermal Parameters (1) | TPS22917 DBV (SOT-23) 6 PINS | UNIT |
|---|---|---|---|
| θ JA | Junction-to-ambient thermal resistance | 183 | °C/W |
| θ JCtop | Junction-to-case (top) thermal resistance | 152 | °C/W |
| θ JB | Junction-to-board thermal resistance | 34 | °C/W |
| ψ JT | Junction-to-top characterization parameter | 37 | °C/W |
| ψ JB | Junction-to-board characterization parameter | 33 | °C/W |
TPS22917DBVR.A Typical Application
This section highlights some of the design considerations when implementing this device in various applications.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| TPS22917 | Texas Instruments | — |
| TPS22917DBVR | Texas Instruments | SOT-23-6 |
| TPS22917DBVT | Texas Instruments | SOT-23-6 |
| TPS22917DBVT.A | Texas Instruments | — |
| TPS22917L | Texas Instruments | — |
| TPS22917LDBVR | Texas Instruments | SOT-23-6 |
| TPS22917LDBVR.A | Texas Instruments | — |
More datasheets
Ask your AI agent about the TPS22917DBVR.A
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the TPS22917DBVR.A run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.