TL072CP

The TL072CP is an electronic component from Texas Instruments. View the full TL072CP datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

TL072CP shares its datasheet with TL072, whose page lists every part number it covers.

Official TL072CP datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

TL072CP Key Specifications

Parameter	Value
Amplifier Type	J-FET
Input Bias Current	65 pA
Quiescent Current	1.4mA (x2 Channels)
Gain Bandwidth Product	5.25 MHz
Mounting Type	Through Hole
Number of Circuits	2
Operating Temperature	0°C ~ 70°C (TA)
Package / Case	8-DIP (0.300", 7.62mm)
Slew Rate	13V/µs
Supplier Device Package	8-PDIP
Input Offset Voltage	3 mV
Supply Voltage Span (Max)	30 V
Supply Voltage Span (Min)	10 V

TL072CP Overview

Part: TL072 (TL07xx family: TL071, TL072, TL074; H, C, I, M grades) — Texas Instruments

Type: Low-Noise, FET-Input Operational Amplifier (dual for TL072)

Description: Dual JFET-input op amp with 4.5–40 V total supply (±2.25 to ±20 V), 20 V/μs typical slew rate (TL07xH), 1 mV typical offset (TL07xH) and 37 nV/√Hz typical noise at 1 kHz.

Operating Conditions:

Supply voltage (VCC+ − VCC−): 4.5–40 V (all other devices); 10–30 V for NS/PS packages and all TL07xM devices
Operating temperature: grade-dependent, TL07xC 0 to 70 °C; TL07xI -40 to 85 °C; TL07xH -40 to 125 °C; TL07xM -55 to 125 °C
Input voltage: (VCC−) + 4 V to (VCC+) + 0.1 V (all other devices)

Absolute Maximum Ratings:

Supply voltage: 42 V (all other devices); 36 V (NS and PS packages, all TL07xM devices)
Input current (clamp): ±10 mA (all other devices); 50 mA (NS/PS packages, TL07xM devices)
Output short-circuit: continuous (to ground, one amplifier per package)
Junction temperature: 150 °C
Storage temperature: -65 to 150 °C
ESD: HBM ±2000 V, CDM ±1000 V

Key Specs:

Slew rate: 20 V/μs typ (TL07xH)
Input offset voltage: 1 mV typ (TL07xH)
Offset voltage drift: 2 μV/°C
Supply current: 940 μA/channel typ (TL07xH)
Input voltage noise: 37 nV/√Hz typ at f = 1 kHz
Total harmonic distortion: 0.003% typ
Thermal resistance RθJA (dual): 147.8 °C/W (D, SOIC-8), 181.5 °C/W (DDF), 85 °C/W (P, PDIP-8), 95 °C/W (PS), 200.3 °C/W (PW), 169.8 °C/W (U)

Features:

Common-mode input range includes VCC+
Wide common-mode and differential voltage ranges
Low input bias and offset currents
Output short-circuit protection
Integrated EMI and RF filters (TL07xH)
High ESD (1.5 kV HBM, TL07xH)

Applications:

Solar energy: string and central inverters
Motor drives: AC and servo drive control and power-stage modules
Single-phase online UPS
Three-phase UPS
Pro audio mixers
Battery test equipment

Package:

TL072x: D (SOIC-8), DDF (SOT-23-THIN-8), P (PDIP-8), PS (SO-8), PW (TSSOP-8)
TL072M: FK (LCCC-20), JG (CDIP-8), U (CFP-10)

TL072CP Features

High slew rate: 20V/μs (TL07xH, typ)
Low offset voltage: 1mV (TL07xH, typ)
Low offset voltage drift: 2μV/°C
Low power consumption: 940μA/ch (TL07xH, typ)
Wide common-mode and differential voltage ranges
-Common-mode input voltage range includes VCC+
Low input bias and offset currents
Low noise:
-Vn = 37nV/√Hz (typ) at f = 1kHz
Output short-circuit protection
Low total harmonic distortion: 0.003% (typ)
Wide supply voltage:
-±2.25V to ±20V, 4.5V to 40V

TL072CP Applications

TL072CP Pin Configuration

Figure 4-1. TL071H DBV Package, 5-Pin SOT-23 (Top View)

Figure 4-2. TL071H DCK Package, 5-Pin SC70 (Top View)

Figure 4-3. TL071x D Package, 8-Pin SOIC and P Package, 8-pin PDIP (Top View)

Table 4-1. Pin Functions: TL071x

PIN - NAME	PIN - NO. - DBV (SOT-23)	PIN - NO. - DCK (SC70)	PIN - NO. - D (SOIC)	PIN - NO. - P (PDIP)	TYPE	DESCRIPTION
IN-	4	3	2	2	Input	Inverting input
IN+	3	1	3	3	Input	Noninverting input
NC	-	-	8	8	-	Do not connect
NC	-	-	1	1	-	Do not connect
NC	-	-	5	5	-	Do not connect
OUT	1	4	6	6	Output	Output
VCC-	2	2	4	4	-	Power supply
VCC+	5	5	7	7	-	Power supply

Figure 4-4. TL071C PS Package, 8-Pin SO (Top View)

Table 4-1. Pin Functions: TL071x

Table 4-2. Pin Functions: TL071C

PIN - NAME	PIN - NO.	TYPE	DESCRIPTION
IN-	2	Input	Inverting input
IN+	3	Input	Noninverting input
NC	8	-	Do not connect
OFFSET N1	1	-	Input offset adjustment
OFFSET N2	5	-	Input offset adjustment
OUT	6	Output	Output
VCC-	4	-	Power supply
VCC+	7	-	Power supply

Table 4-2. Pin Functions: TL071C

www.ti.com

Figure 4-5. TL072x D, DDF, JG, P, PS, and PW Packages, 8-Pin SOIC, SOT-23-THIN, CDIP, PDIP, SO, and TSSOP (Top View)

Table 4-3. Pin Functions: TL072x

PIN - NAME	PIN - NO.	TYPE	DESCRIPTION
1IN-	2	Input	Inverting input
1IN+	3	Input	Noninverting input
1OUT	1	Output	Output
2IN-	6	Input	Inverting input
2IN+	5	Input	Noninverting input
2OUT	7	Output	Output
VCC-	4	-	Power supply
VCC+	8	-	Power supply

Figure 4-6. TL072M U Package, 10-Pin CFP (Top View)

Table 4-3. Pin Functions: TL072x

PIN - NAME	PIN - NO.	TYPE	DESCRIPTION
1IN-	3	Input	Inverting input
1IN+	4	Input	Noninverting input
1OUT	2	Output	Output
2IN-	7	Input	Inverting input
2IN+	6	Input	Noninverting input
2OUT	8	Output	Output
NC	1, 10	-	Do not connect
VCC-	5	-	Power supply
VCC+	9	-	Power supply

TL072CP Electrical Characteristics

at V S = (V CC+ ) - (V CC-) = 4.5 V to 40 V (±2.25 V to ±20 V), T A = 25°C, R L = 10 kΩ connected to VS / 2, VCM = VS / 2, and VOUT = VS / 2 (unless otherwise noted)

PARAMETER	PARAMETER	TEST CONDITIONS	TEST CONDITIONS	MIN	TYP	MAX	UNIT
OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE	OFFSET VOLTAGE
V OS	Input offset voltage				±1	±4	mV
V OS			T A = -40°C to +125°C			±5
dV OS /dT	Input offset voltage drift		T A = -40°C to +125°C		±2		μV/ °C
PSRR	Input offset voltage versus power supply	V S = 5 V to 40 V, V CM = V S / 2	T A = -40°C to +125°C		±1	±10	μV/V
PSRR	Channel separation	f = 0 Hz			10		μV/V
INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT	INPUT BIAS CURRENT
	Input bias current				±1	±120	pA
I B	Input bias current		DCK and DBV packages		±1	±300	pA
	Input bias current		T A = -40°C to +125°C (1)			±5	nA
I OS	Input offset current				±0.5	±120	pA
I OS	Input offset current		DCK and DBV packages		±0.5	±250	pA
I OS	Input offset current		T A = -40°C to +125°C (1)			±5	nA
NOISE	NOISE	NOISE	NOISE	NOISE	NOISE	NOISE	NOISE
E N	Input voltage noise	f = 0.1 Hz to 10 Hz			9.2		μV PP
E N	Input voltage noise				1.4		μV RMS
e N	Input voltage noise density	f = 1 kHz			37		nV/√Hz
e N	Input voltage noise density	f = 10 kHz			21
i N	Input current noise	f = 1 kHz			80		fA/√Hz
INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE	INPUT VOLTAGE RANGE
V CM	Common-mode voltage			(V CC- ) + 1.5		(V CC+ )	V
V CM		V S = 40 V, (V CC- ) + 2.5 V <		100	105		dB
CMRR	Common-mode rejection ratio	V CM < (V CC+ ) - 1.5 V	T A = -40°C to +125°C	95			dB
CMRR	Common-mode rejection ratio	V S = 40 V, (V CC- ) + 2.5 V <		90	105		dB
CMRR	Common-mode rejection ratio	V CM < (V CC+ )	T A = -40°C to +125°C	80			dB
INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE	INPUT CAPACITANCE
Z ID	Differential				100 \|\| 2		MΩ \|\| pF
Z ICM	Common-mode				6 \|\| 1		TΩ \|\| pF
OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN	OPEN-LOOP GAIN
A OL	Open-loop voltage gain	V S = 40 V, V CM = V S / 2, (V CC- ) + 0.3 V < V O < (V CC+ ) - 0.3 V	T A = -40°C to +125°C	118	125		dB
A OL	Open-loop voltage gain	V S = 40 V, V CM = V S / 2, R L = 2 kΩ, (V CC- ) + 1.2 V < V O < (V CC+ ) - 1.2 V	T A = -40°C to +125°C	115	120		dB
FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE	FREQUENCY RESPONSE
GBW	Gain-bandwidth product				5.25		MHz
SR	Slew rate	V S = 40 V, G = +1, C L = 20 pF			20		V/μs
t S		To 0.1%, V S = 40 V, V STEP = 10 V , G = +1, C L = 20	pF		0.63
t S		To 0.1%, V S = 40 V, V STEP = 2 V , G = +1, C L = 20	pF		0.56
t S	Settling time	To 0.01%, V S = 40 V, V STEP = 10 V , G = +1, C L =	20 pF		0.91		μs
t S		To 0.01%, V S = 40 V, V STEP = 2 V , G = +1, C L = 20	pF		0.48
	Phase margin	G = +1, R L = 10kΩ, C L = 20	pF		56		°
	Overload recovery time	V IN × gain > V S			300		ns
THD+N	Total harmonic distortion + noise	V S = 40 V, V O = 6 V RMS , G = +1, f = 1	kHz		0.00012		%
EMIRR	EMI rejection ratio	f = 1 GHz			53		dB

TL072CP Absolute Maximum Ratings

over operating ambient temperature range (unless otherwise noted) (1)

			MIN	MAX	UNIT
		All NS and PS packages; All TL07xM devices	-0.3	36	V
Supply voltage, V S = (V+)	Supply voltage, V S = (V+)	All other devices	0	42	V
		All NS and PS packages; All TL07xM devices	(V CC- ) - 0.3	(V CC- ) + 36	V
	Signal pins	All NS and PS packages; All TL07xM devices	(V CC- ) - 0.3	(V CC- ) + 36	V
	Differential voltage (2)	(3)			V
	Differential voltage (2)	All other devices		V S + 0.2	V
	Current (2)	All NS and PS packages; All TL07xM devices		50	mA
	Current (2)	All other devices	-10	10	mA
Output short-circuit (4)	Output short-circuit (4)	Output short-circuit (4)	Continuous	Continuous	Continuous
Operating ambient temperature, T A	Operating ambient temperature, T A	Operating ambient temperature, T A	-55	150	°C
Junction temperature, T J	Junction temperature, T J	Junction temperature, T J		150	°C
Case temperature for 60 seconds - FK package	Case temperature for 60 seconds - FK package	Case temperature for 60 seconds - FK package		260	°C
Lead temperature 1.8 mm (1/16 inch) from case for 10 seconds	Lead temperature 1.8 mm (1/16 inch) from case for 10 seconds	Lead temperature 1.8 mm (1/16 inch) from case for 10 seconds		300	°C
Storage temperature, T stg	Storage temperature, T stg	Storage temperature, T stg	-65	150	°C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions . Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Input pins are diode-clamped to both power-supply rails on all new die. Current limit input signals that swing more than 0.5 V beyond the supply rails to 10 mA or less.
(3) Differential voltage only limited by input voltage.
(4) Short-circuit to ground, one amplifier per package.

TL072CP Recommended Operating Conditions

over operating ambient temperature range (unless otherwise noted)

			MIN	MAX	UNIT
V S	Supply voltage, (V CC+ ) - (V CC- )	All NS and PS packages; All TL07xM devices (1)	10	30	V
V S		All other devices	4.5	40	V
V I	Input voltage	All NS and PS packages; All TL07xM devices	(V CC- ) + 2	(V CC+ ) + 0.1	V
V I	Input voltage	All other devices	(V CC- ) + 4	(V CC+ ) + 0.1	V
T A	Specified temperature (2)	TL07xM	-55	125	°C
T A	Specified temperature (2)	TL07xH	-40	125	°C
T A	Specified temperature (2)	TL07xI	-40	85	°C
T A	Specified temperature (2)	TL07xC	0	70	°C

TL072CP Thermal Information

THERMAL METRIC (1)	THERMAL METRIC (1)	TL071xx - D (SOIC) - 8 PINS	TL071xx - DCK (SC70) - 5 PINS	TL071xx - DBV (SOT-23) - 5 PINS	TL071xx - P (PDIP) - 8 PINS	TL071xx - PS (SO) - 8 PINS	UNIT
R θJA	Junction-to-ambient thermal resistance	158.8	217.5	212.2	85	95	°C/W
R θJC(top)	Junction-to-case (top) thermal resistance	98.6	113.1	111.1	-	-	°C/W
R θJB	Junction-to-board thermal resistance	102.3	63.8	79.4	-	-	°C/W
ψ JT	Junction-to-top characterization parameter	45.8	34.8	51.8	-	-	°C/W
ψ JB	Junction-to-board characterization parameter	101.5	63.5	79.0	-	-	°C/W
R θJC(bot)	Junction-to-case (bottom) thermal resistance	N/A	N/A	N/A	N/A	N/A	°C/W

TL072CP Typical Application

A typical application for an operational amplifier is an inverting amplifier. This amplifier takes a positive voltage on the input, and makes the voltage a negative voltage. In the same manner, the amplifier makes negative voltages positive.

Other Operational Amplifiers

LM358 – onsemi, Dual Operational Amplifier
NE5532 – Texas Instruments, Dual Operational Amplifier
AD623A – Analog Devices, Rail-to-Rail Instrumentation Amplifier
AD623ARMZ-REEL7 – Analog Devices, Rail-to-Rail Instrumentation Amplifier
AD623ARZ – Analog Devices, Rail-to-Rail Instrumentation Amplifier
AD623ARZ-RL – Analog Devices, Rail-to-Rail Instrumentation Amplifier
AD623B – Analog Devices, Rail-to-Rail Instrumentation Amplifier
AD623BNZ – Analog Devices, Rail-to-Rail Instrumentation Amplifier

All Operational Amplifiers datasheets All Texas Instruments datasheets (2,418)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TL072CP

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TL072CP run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.