Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

TAS5711

Digital Audio Power Amplifier

The TAS5711 is a digital audio power amplifier from Texas Instruments. View the full TAS5711 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

Official TAS5711 datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Digital Audio Power Amplifier

Package

HTQFP-48

TAS5711 Key Specifications

ParameterValue
Snr106 dB
EfficiencyUp to 90%
Output Power20W (into 8Ω load @ 18V)
Package Dimensions7mm x 7mm
Sample Rate Support8kHz to 48kHz
Communication InterfacesI2C, I2S
Supply Voltage Power Pvdd8V to 26V
Operating Temperature Range0°C to 85°C
Supply Voltage Digital Analog3.0V to 3.6V

TAS5711 Overview

Part: TAS5711 (TAS5711PHPR) — Texas Instruments

Type: Digital Audio Power Amplifier (Class-D, with EQ, DRC, 2.1 mode)

Description: 20-W per channel digital-input Class-D audio amplifier with 8–26 V half-bridge supply, 3.3 V logic supply, 90% efficiency, 106 dB SNR, 21 programmable biquads and DRC.

Operating Conditions:

  • Supply voltage: DVDD/AVDD 3–3.6 V; PVDD_x 8–26 V
  • Operating ambient temperature: 0 to 85 °C
  • Junction temperature: 0 to 125 °C (recommended)
  • Load impedance (BTL): 6 Ω min, 8 Ω nominal; output inductance ≥ 10 μH under short-circuit condition
  • MCLK frequency: 2.8224–24.576 MHz

Absolute Maximum Ratings:

  • Supply voltage: DVDD, AVDD −0.3 to 3.6 V; PVDD_x −0.3 to 30 V
  • OUT_x to PGND_x: 32 V; BST_x to PGND_x: 43 V
  • Input clamp / output clamp current: ±20 mA
  • Operating junction temperature: 0 to 150 °C
  • Storage temperature: −40 to 125 °C

Key Specs:

  • Output power (BTL, PVDD = 18 V, 8 Ω, 1 kHz): 21 W at 10% THD, 20 W at 7% THD
  • Output power (PBTL, PVDD = 18 V, 4 Ω): 42.8 W at 10% THD
  • THD+N (PVDD = 18 V, PO = 1 W): 0.06%
  • SNR: 106 dB (A-weighted, maximum power at THD < 1%)
  • Output integrated noise: 44 μV (A-weighted)
  • Supply current, normal mode: DVDD/AVDD 48 mA typ (70 mA max); PVDD no load 30 mA typ (55 mA max)
  • Output FET rDS(on): 180 mΩ (high-side and low-side, TJ = 25 °C)
  • Overcurrent limit: 4.5 A typ (ROCP = 22 kΩ); undervoltage trip 7.2 V (PVDD falling); overtemperature error 150 °C

Features:

  • 2.1 mode (2 SE + 1 BTL), 2.0 mode (2 BTL), and single-filter PBTL mode
  • AD and BD modulation modes
  • Up to 90% efficiency; no heatsink required
  • One serial audio input (I²S/LJ/RJ), 8–48 kHz sample rates
  • Independent channel volume controls; separate DRC for satellite and subchannels
  • 21 programmable biquads for speaker EQ
  • Autobank switching and automatic sample-rate detect
  • I²C control with address select pin; control interface operates without MCLK
  • Thermal and short-circuit protection
  • Requires only 3.3 V and PVDD

Applications:

  • Television
  • iPod dock
  • Sound bar

Package:

  • 48-pin HTQFP (PHP), 7 mm × 7 mm

TAS5711 Features

  • 2 · Audio Input/Output
  • Benefits
  • -20-W Into an 8Ω Load From an 18-V Supply
  • -Up to 90% Efficient
  • -Wide PVDD Range, From 8 V to 26 V
  • -AD and BD Filter Mode Support
  • -Efficient Class-D Operation Eliminates Need for Heatsinks
  • -One Serial Audio Input (Two Audio Channels)
  • -2.1 Mode (2 SE + 1 BTL)
  • -2.0 Mode (2 BTL)
  • -Single-Filter PBTL Mode Support
  • -I 2 C Address Selection Pin (Chip Select)
  • -Supports 8-kHz to 48-kHz Sample Rate (LJ/RJ/I 2 S)
  • Audio/PWM Processing
  • -Independent Channel Volume Controls With 24-dB to Mute
  • -Separate Dynamic Range Control for Satellite and Subchannels
  • -21 Programmable Biquads for Speaker EQ and Other Audio Processing Features
  • -Programmable Coefficients for DRC Filters
  • -SNR: 106 dB, A-Weighted
  • -EQ: Speaker Equalization Improves Audio Performance
  • -DRC: Dynamic Range Compression. Can Be Used As Power Limiter. Enables Speaker Protection, Easy Listening, Night-Mode Listening.
  • -Separate DRC for Satellite and Subchannels
  • -Autobank Switching: Preload Coefficients for Different Sample Rates. No Need to Write new Coefficients to the Part When Sample Rate Changes.
  • -Autodetect: Automatically Detects Sample-Rate Changes. No Need for External Microprocessor Intervention
  • Requires Only 3.3 V and PVDD

TAS5711 Applications

  • -DC Blocking Filters
  • -Support for 3D Effects
  • General Features
  • -Serial Control Interface Operational Without MCLK
  • -Factory-Trimmed Internal Oscillator for Automatic Rate Detection
  • -Surface Mount, 48-Pin, 7-mm × 7-mm HTQFP Package
  • -Thermal and Short-Circuit Protection
  • -Support for AD or BD Mode

1

2

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. iPod is a trademark of Apple Inc.

  • Television
  • iPod™ Dock
  • Sound Bar

TAS5711 Pin Configuration

TAS5711 Electrical Characteristics

TA = 25°, PVCC_x = 18V, DVDD = AVDD = 3.3V, RL= 8 Ω , BTL AD Mode, FS = 48KHz (unless otherwise noted)

PARAMETERPARAMETERPARAMETERTEST CONDITIONSMIN TYPMAXUNIT
V OHHigh-level output voltageA_SEL and SDAI OH = -4 mA DVDD = AVDD = 3 V2.4V
V OLLow-level output voltageA_SEL and SDAI OL = 4 mA DVDD = AVDD = 3 V0.5V
I ILLow-level input currentV I < V IL ; DVDD = AVDD = 3.6V75m A
I IHHigh-level input currentV I > V IH ; DVDD = AVDD = 3.6V75 (1)m A
I DD3.3 V supply current3.3 V supply voltage (DVDD, AVDD)Normal Mode4870mA
I DD3.3 V supply current3.3 V supply voltage (DVDD, AVDD)Reset (RESET = low, PDN = high)2432mA
I PVDDHalf-bridge supply currentNo load (PVDD_x)Normal Mode3055mA
I PVDDHalf-bridge supply currentNo load (PVDD_x)Reset (RESET = low, PDN = high)513mA
r DS(on) (2)Drain-to-source resistance, LST J = 25°C, includes metallization resistanceT J = 25°C, includes metallization resistance180m Ω
r DS(on) (2)Drain-to-source resistance, HST J = 25°C, includes metallization resistanceT J = 25°C, includes metallization resistance180m Ω
I/O ProtectionI/O ProtectionI/O ProtectionI/O ProtectionI/O ProtectionI/O ProtectionI/O ProtectionI/O Protection
V uvpUndervoltage protection limitPVDD fallingPVDD falling7.2V
V uvp,hystUndervoltage protection limitPVDD risingPVDD rising7.6V
OTE (3)Overtemperature error150°C
OTE HYST (3)Extra temperature drop required to recover from error30°C
OLPCOverload protection counterf PWM = 384 kHzf PWM = 384 kHz0.63ms
I OCOvercurrent limit protectionResistor-programmable, max. current, R OCP = 22 k ΩResistor-programmable, max. current, R OCP = 22 k Ω4.5A
I OCTOvercurrent response time150ns
R OCPOC programming resistor rangeResistor tolerance = 5% for typical value; the minimum resistance should not be less than 20 k Ω .Resistor tolerance = 5% for typical value; the minimum resistance should not be less than 20 k Ω .20 22k Ω
R PDInternal pulldown resistor at the output of each half-bridgeConnected when drivers are tristated to provide bootstrap capacitor charge.Connected when drivers are tristated to provide bootstrap capacitor charge.3k Ω

TAS5711 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1)

VALUEUNIT
Supply voltageDVDD, AVDD-0.3 to 3.6V
Supply voltagePVDD_x-0.3 to 30V
OC_ADJ-0.3 to 4.2V
3.3-V digital input-0.5 to DVDD + 0.5V
5-V tolerant (2) digital input (except MCLK)-0.5 to DVDD + 2.5 (3)V
5-V tolerant MCLK input-0.5 to AVDD + 2.5 (3)V
OUT_x to PGND_xOUT_x to PGND_x32 (4)V
BST_x to PGND_xBST_x to PGND_x43 (4)V
Input clamp current, I IKInput clamp current, I IK±20mA
Output clamp current, I OKOutput clamp current, I OK±20mA
Operating free-air temperatureOperating free-air temperature0 to 85°C
Operating junction temperature rangeOperating junction temperature range0 to 150°C
Storage temperature range, T stgStorage temperature range, T stg-40 to 125°C
MINNOMMAXUNIT
Digital/analog supply voltageDVDD, AVDD33.33.6V
Half-bridge supply voltagePVDD_x826V
V IHHigh-level input voltage5-V tolerant2V
V ILLow-level input voltage5-V tolerant0.8V
T AOperating ambient temperature range085°C
T J (1)Operating junction temperature range0125°C
R L (BTL)Load impedanceOutput filter: L = 15 m H, C = 680 nF.68Ω
L O (BTL)Output-filter inductanceMinimum output inductance under short-circuit condition10m H

TAS5711 Thermal Information

THERMAL METRIC (1)(2)THERMAL METRIC (1)(2)TAS5711 PHP (48 PIN)UNITS
q JAJunction-to-ambient thermal resistance29.9°C/W
q JCtopJunction-to-case (top) thermal resistance20.5°C/W
q JBJunction-to-board thermal resistance12.5°C/W
y JTJunction-to-top characterization parameter0.3°C/W
y JBJunction-to-board characterization parameter7.3°C/W
q JCbotJunction-to-case (bottom) thermal resistance0.7°C/W

TAS5711 Typical Application

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
TAS5711PHPTexas InstrumentsHTQFP-48 7x7mm
TAS5711PHPRTexas Instruments48-PowerTQFP

More datasheets

All Texas Instruments datasheets (2,417)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the TAS5711

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the TAS5711 run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.