SY7200
Boost LED DriverThe SY7200 is a boost led driver from Silergy. View the full SY7200 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
Official SY7200 datasheet (PDF) — the source this page was extracted from.
Manufacturer
SilergyCategory
Boost LED Driver
SY7200 Key Specifications
| Parameter | Value |
|---|---|
| Lifecycle Status | Production (Last Updated: 1 month ago) |
| Part Series | SY7200 |
| Feedback reference voltage | 196 / 200 / 204 mV (min/typ/max); LED current set by I_OUT = 0.2 V / R1 |
| Quiescent current | 0.1 mA typ, 0.6 mA max (VFB = 0.3 V) |
| Shutdown current | 10 μA typ, 15 μA max (EN = 0) |
| Low-side main FET RDS(ON) | 200 mΩ typ (140–230 mΩ) |
| Main FET current limit | 2 / 2.6 / 3.5 A (min/typ/max, 10% duty) |
| Oscillator frequency | 0.8 / 1.0 / 1.2 MHz (IOUT = 100 mA) |
| Input UVLO threshold | 2.55 V typ (2.4–2.75 V), 0.1 V hysteresis |
| Open-LED output clamp voltage | 28 / 30 / 33 V |
| Max duty cycle | 90% typ; min on-time: 100 ns typ |
| Thermal shutdown | 150 °C typ, 20 °C hysteresis |
| Thermal resistance SOT23-6 | θJA 170 °C/W, θJC 130 °C/W |
SY7200 Overview
Part: SY7200AABC — Silergy
Type: Boost (Step-Up) Constant-Current LED Driver
Description: 2.8–30 V input, 1 MHz fixed-frequency boost LED driver with 2 A switch current limit, 200 mV feedback reference, and open-LED protection at 30 V, driving up to eight white LEDs in series.
Operating Conditions:
- Supply voltage: 2.8–30 V
- Operating temperature: -40 to 85 °C ambient (junction -40 to 125 °C)
- PWM dimming frequency on EN/PWM: 20 kHz–1 MHz
Absolute Maximum Ratings:
- IN, EN: 32 V
- LX: -0.3 V to 33 V (tested down to -3 V for <10 ns and up to +36 V for <50 ns)
- OVP: 36 V
- All other pins: 4 V
- Power dissipation (TA = 25 °C, SOT23-6): 0.6 W
- Max junction temperature: 125 °C
- Storage temperature: -65 to 150 °C
- Lead temperature (soldering, 10 s): 260 °C
Key Specs:
- Feedback reference voltage: 196 / 200 / 204 mV (min/typ/max); LED current set by I_OUT = 0.2 V / R1
- Quiescent current: 0.1 mA typ, 0.6 mA max (VFB = 0.3 V)
- Shutdown current: 10 μA typ, 15 μA max (EN = 0)
- Low-side main FET RDS(ON): 200 mΩ typ (140–230 mΩ)
- Main FET current limit: 2 / 2.6 / 3.5 A (min/typ/max, 10% duty)
- Oscillator frequency: 0.8 / 1.0 / 1.2 MHz (IOUT = 100 mA)
- Input UVLO threshold: 2.55 V typ (2.4–2.75 V), 0.1 V hysteresis
- Open-LED output clamp voltage: 28 / 30 / 33 V
- Max duty cycle: 90% typ; min on-time: 100 ns typ
- Thermal shutdown: 150 °C typ, 20 °C hysteresis
- Thermal resistance SOT23-6: θJA 170 °C/W, θJC 130 °C/W
Features:
- Input voltage range of 2.8 to 30 V
- Switch current limit of 2 A
- Drives LED strings up to 30 V
- 1 MHz fixed frequency minimizes external components
- EN/PWM dimming frequency of 20 kHz–1 MHz
- Internal soft-start limits inrush current
- Open LED overvoltage protection
- RoHS compliant and halogen free
Applications:
- GPS navigation systems
- Handheld devices
- Portable media players
Package:
- SOT23-6 (3000 pcs per 7" reel, 8 mm tape)
SY7200 Features
- Input voltage range: 2.8 to 30V
- Switch current limit 2A
- Drives LED strings up to 30V
- 1MHz fixed frequency minimizes the external components
- Dimming frequency for EN/PWM pin: 20kHz~1MHz
- Internal softstart limits the inrush current
- Open LED over voltage protection
- RoHS Compliant and Halogen Free
SY7200 Applications
Figure 1. Schematic Diagram
SY7200 Electrical Characteristics
(VIN = 3.6V, TA = 25° C, unless otherwise specified)
| Parameter | Symbol | Conditions | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Input Voltage Range | V IN | 2.8 | 30 | V | ||
| Quiescent Current | I Q | V FB =0.3V | 0.1 | 0.6 | mA | |
| Shutdown Current | I SHDN | EN=0 | 10 | 15 | μA | |
| Feedback Reference Voltage | V REF | 196 | 200 | 204 | mV | |
| FB Input Current | I FB | V FB =0.3V | 1 | μA | ||
| Low Side Main FET RON | R DS(ON) | 140 | 200 | 230 | mΩ | |
| Main FET Current Limit | I LIM | 10% Duty | 2 | 2.6 | 3.5 | A |
| EN Rising Threshold | V ENH | 1.5 | V | |||
| EN Falling Threshold | V ENL | 0.4 | V | |||
| Input UVLO Threshold | V UVLO | 2.4 | 2.55 | 2.75 | V | |
| UVLO Hysteresis | V HYS | 0.1 | V | |||
| Oscillator Frequency | F OSC | I OUT =100mA | 0.8 | 1.0 | 1.2 | MHz |
| Min On Time | 100 | ns | ||||
| Max Duty Cycle | 90 | % | ||||
| Thermal Shutdown | T SD | 150 | °C | |||
| Thermal Hysteresis | T HYST | 20 | °C | |||
| Output Clamp voltage | V OCL | 'Open LED' | 28 | 30 | 33 | V |
| PWMdimming frequency | 20k | 1M | Hz |
Note 1 : Stresses beyond the 'Absolute Maximum Ratings' may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Note 2 : θJA is measured in the natural convection at TA = 25° C on a low effective single layer thermal conductivity test board of JEDEC 51-3 thermal measurement standard. Test condition: Device mounted on 2' x 2' FR-4 substrate PCB, 2oz copper, with minimum recommended pad on top layer and thermal vias to bottom layer ground plane.
Note 3: The device is not guaranteed to function outside its operating conditions.
SY7200 Absolute Maximum Ratings
IN, EN ---------------------------------------------------------- ---------------------------------------------------- 32V
LX --------------------------------------------------------------------------------------------------- -0.3V
(
*1
)
to 33V
(
*2
OVP ---------------------------------------------------------------------------------------------------------------- 36V
All other pins --------------------------------------------------------------------------------------------------------- 4V
Power Dissipation, PD @ TA = 25° C, SOT23-6-----------------------------------------------------------------0.6W
Package Thermal Resistance (Note 2)
SOT23-6, θJA --------------------------------------------------------------------------------------- 170° C/W
SOT23-6, θJC --------------------------------------------------------------------------------------- 130° C/W
Junction Temperature Range ----------------------------------------------------------------------------------- 125° C
Lead Temperature (Soldering, 10 sec.) ------------------------------------------------------------------------ 260° C
Storage Temperature Range ------------------------------------------------------------------------- -65° C to 150° C
(*1) LX Voltage tested down to -3V<10ns
(*2) LX Voltage tested up to +36V<50ns
SY7200 Recommended Operating Conditions
Input Voltage Supply-------------------------------------------------------------------------------------- 2.8V to 30V
Junction Temperature Range ------------------------------------------------------------------------ -40° C to 125° C
Ambient Temperature Range ------------------------------------------------------------------------- -40° C to 85° C
)
SY7200 Typical Application
Figure 1. Schematic Diagram
SY7200 Package Information
Notes: All dimensions are in millimeters.
All dimensions don't include mold flash & metal burr.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| SY7200A | Silergy | — |
| SY7200AABC | Silergy | SOT23-6 |
More datasheets
Ask your AI agent about the SY7200
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the SY7200 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.