Skip to main content

QMC5883L

3-Axis Magnetic Sensor

The QMC5883L is a 3-axis magnetic sensor from Not explicitly stated in provided pages. View the full QMC5883L datasheet below including pinout, absolute maximum ratings.

Manufacturer

Not explicitly stated in provided pages

Category

3-Axis Magnetic Sensor

Package

LGA-16

Overview

Part: QMC5883L

Type: 3-Axis Magnetic Sensor

Description: A multi-chip three-axis magnetic sensor with integrated magnetic sensors and signal condition ASIC, featuring 16-bit ADC, ±8 Gauss field range, temperature compensation, and I²C interface, enabling 1° to 2° compass heading accuracy.

Operating Conditions:

  • Supply voltage: 2.16–3.6 V
  • I/O Voltage: 1.65–3.6 V
  • Operating temperature: -40 to 85 °C
  • Output Data Rate: 10–200 Samples/sec

Absolute Maximum Ratings:

  • Max VDDIO: 5.4 V
  • Max VDD: 5.4 V
  • Max storage temperature: 125 °C
  • Exposed to Magnetic Field (all directions): 50000 Gauss

Key Specs:

  • Standby Current: 3 μA (Typ)
  • Continuous Mode Current (ODR=10Hz, Low Power Mode): 75 μA (Typ)
  • Peak Current in Active State: 2.6 mA (Typ)
  • Sensor Field Range: ±8 Gauss
  • Digital Resolution Field Resolution: 2 mGauss (Typ)
  • Sensitivity (Field Range = ±2G): 12000 LSB/G (Typ)
  • Linearity (Field Range = ±2G): 0.1 %FS (Typ)
  • X-Y-Z Orthogonality: 90±1 degree (Typ)

Features:

  • 3-Axis Magneto-Resistive Sensors
  • 16 Bit ADC With Low Noise AMR Sensors
  • Wide Magnetic Field Range (± 8 Gauss)
  • Temperature Compensated Data Output and Temperature Output
  • I²C Interface with Standard and Fast Modes
  • Wide Range Operation Voltage (2.16V To 3.6V)
  • Low Power Consumption (75 μA)
  • Maximum 200Hz Data Output Rate
  • Offset cancellation
  • Self-aligned magnetic field to restore magnetic state

Applications:

  • Compassing
  • Navigation
  • Gaming in drone, robot, mobile and personal hand-held devices
  • LBS Applications

Package:

  • 16-pin Land Grid Array (LGA) (3x3x0.9mm)

Pin Configuration

QMC5883L Pinout

Package Type: LGA-16 (3mm × 3mm × 0.9mm)

Pin NumberPin NameTypeDescription
1SCLISerial Clock - I²C Master/Slave Clock
2VDDPPower Supply (2.16V to 3.6V)
3NCNot to be Connected
4S1OTie to VDDIO
5NCNot to be Connected
6NCNot to be Connected
7NCNot to be Connected
8SETPSet/Reset Strap Positive - S/R Capacitor (C2) Connection
9GNDPSupply Ground
10C1Reservoir Capacitor (C1) Connection
11GNDPSupply Ground
12SETCS/R Capacitor (C2) Connection - Driver Side
13VDDIOPIO Power Supply (1.71V to VDD)
14NCNot to be Connected
15DRDYOData Ready, Interrupt Pin. Default low. Data ready high until data register is read.
16SDAI/OSerial Data - I²C Master/Slave Data

Notes

  • NC pins (3, 5, 6, 7, 14): Must not be connected; leave floating.
  • Power pins: VDD (pin 2) and VDDIO (pin 13) must be decoupled with appropriate capacitors. GND pins (9, 11) must be connected to ground.
  • I²C interface: SCL (pin 1) and SDA (pin 16) require pull-up resistors for I²C operation.
  • Capacitor connections: SETP (pin 8), C1 (pin 10), and SETC (pin 12) are for external set/reset capacitor network integration.
  • S1 pin (pin 4): Should be tied to VDDIO for proper operation.

Absolute Maximum Ratings

Table 3. Absolute Maximum Ratings (Tested at 25° C except stated otherwise.)

ParameterMIN.MAX.Units
VDDIO-0.35.4V
VDD-0.35.4V
Storage Temperature-40125°C
Exposed to Magnetic Field (all directions)50000Gauss
Reflow ClassificationMSL 3, 260 C Peak TemperatureMSL 3, 260 C Peak TemperatureMSL 3, 260 C Peak Temperature

Ordering Information

Ordering NumberTemperature RangePackagePackaging
QMC5883L-TR-40 °C ~85 °CLGA-16Tape and Reel: 3k pieces/reel

Related Variants

The following components are covered by the same datasheet.

Part NumberManufacturerPackage
QMC5883L-TRNot explicitly stated in provided pagesLGA-16
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Get structured datasheet data via API

Get started free