BQ25616
Standalone Li-ion Buck Battery Charger with Power PathThe BQ25616 is a standalone li-ion buck battery charger with power path from Texas Instruments. View the full BQ25616 datasheet below including key specifications, pinout, electrical characteristics, absolute maximum ratings.
Official BQ25616 datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Standalone Li-ion Buck Battery Charger with Power Path
Package
WQFN-24
BQ25616 Key Specifications
| Parameter | Value |
|---|---|
| BATFET RDSON | 19.5mΩ |
| Safety Timer | 10 hr |
| Charge Current | up to 3.0A |
| Charge Efficiency | 92% at 2A from 5V input |
| Control Interface | Standalone (no I2C) |
| Boost (OTG) Output | 5V up to 1.2A |
| Input OVP Response | 130ns |
| Package Dimensions | 4.00mm × 4.00mm |
| Input Voltage Range | 4V to 13.5V (22V absolute max) |
| Switching Frequency | 1.5MHz |
| Temperature Sensing | Hot/Cold profile (JEITA on BQ25616J) |
| Charge Voltage Options | 4.1V, 4.2V, 4.35V (VSET pin) |
| Charge Current Accuracy | ±6% |
| Charge Voltage Accuracy | ±0.4% |
| Battery Leakage Current (Standby) | 9.5µA |
| Input Current Regulation Accuracy | ±7.5% |
BQ25616 Overview
Part: BQ25616 / BQ25616J — Texas Instruments
Type: Standalone single-cell Li-ion/Li-polymer buck battery charger with power path and boost (OTG) operation
Description: 4–13.5 V input, 3 A (fast charge) standalone 1-cell switch-mode buck charger with NVDC power path, 1.5 MHz switching, and 5 V boost output up to 1.2 A.
Operating Conditions:
- Supply voltage (VBUS): 4–13.5 V
- Operating temperature (ambient): -40 to 85 °C
- Battery voltage: up to 4.35 V
- Input current up to 3.2 A; fast charging current up to 3 A
Absolute Maximum Ratings:
- Max input voltage: VAC 30 V (converter not switching); VBUS 22 V (converter not switching)
- PMID: 22 V; SW: 16 V; BTST: 22 V; ACDRV: 40 V
- BAT, SYS: 7 V (converter not switching)
- Output sink current (STAT, PG): 6 mA
- Junction temperature: -40 to 150 °C
- Storage temperature: -55 to 150 °C
Key Specs:
- Input voltage range: 4–13.5 V (22 V abs-max VBUS rating)
- Fast charging current: up to 3 A (ICHG pin range 300–3000 mA)
- Input current limit (ILIM pin range): 500–3200 mA
- Charge voltage options: 4.1 V / 4.2 V / 4.35 V with ±0.4% regulation accuracy
- Charge current regulation: ±6%; input current regulation: ±7.5%
- Boost (OTG) output: 5 V, up to 1.2 A
- Charge efficiency: ~92% at 2 A from 5 V input
- Battery leakage (system standby): 9.5 μA; BATFET RDSON 19.5 mΩ
- Minimum system voltage: 3.5 V
- VBUS OVP reaction time: 130 ns
Features:
- 1.5 MHz synchronous switch-mode buck charger
- Boost converter with accurate constant-current limit, soft-start up to 500 μF load, PFM light-load mode
- Narrow VDC (NVDC) power path with instant-on system operation with no or deeply discharged battery
- USB SDP, CDP, DCP, and nonstandard adapter auto-detection via D+/D-
- VINDPM tracks battery voltage; programmable IINDPM via ILIM pin
- Optional external OVPFET (ACDRV) supports input up to 30 V
- JEITA (BQ25616J) or Hot/Cold (BQ25616) TS profile
- 10-hour charge safety timer
- Integrated MOSFETs, current sensing, loop compensation, and bootstrap diode
- Thermal regulation above 110 °C junction
- IEC 62368-1 CB certification
Applications:
- Electronic point of sale (EPOS)
- Wireless speakers
- Industrial, medical, and portable electronics
Package:
- WQFN-24 (RTW), 4.00 mm × 4.00 mm
BQ25616 Features
- High-efficiency, 1.5-MHz, synchronous switchmode buck charger
- -92% charge efficiency at 2 A from 5-V input
- -±0.5% charge voltage regulation
- -Adjustable charge voltage from VSET pin supports 4.1 V, 4.2 V, and 4.35 V with ±0.4% regulation accuracy
- -±6% charge current regulation
- -±7.5% input current regulation
- -Supports JEITA (BQ25616J) or Hot/Cold (BQ25616) temperature sensing profile
- -10-hr charging safety timer
- Support USB On-The-Go (OTG)
- -5-V boost converter with up to 1.2-A output
- -92% boost efficiency at 1-A output
- -Accurate constant current (CC) limit
- -Soft-start up to 500-μF capacitive load
- -PFM mode for light load operation
- Single input supporting USB input, high-voltage adapter, or wireless power
- -Support 4-V to 13.5-V input voltage range with 22-V absolute max input rating
- -130-ns fast turn-off input overvoltage protection with optional external OVPFET standing input voltage up to 30 V
- -Programmable input current limit (IINDPM) with ILIM pin
- -VINDPM threshold automatically tracks battery voltage for maximum power
- -Auto detect USB SDP, CDP, DCP and nonstandard adaptors
- Narrow VDC (NVDC) power path management
- -System instant-on with no battery or deeply discharged battery
- Low RDSON 19.5-mΩ BATFET to minimize charging loss and extend battery run time
- 9.5-μA low battery leakage current with system standby
- High integration includes all MOSFETs, current sensing and loop compensation
- Safety Related Certifications:
- -IEC 62368-1 CB Certification
BQ25616 Applications
- Electronic Point of Sale (EPOS)
- Wireless speaker
- Industrial, medical, portable electronics
BQ25616 Pin Configuration
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | VAC | P | Charger input voltage sensing. Optional external n-channel ACFET is placed between VAC and VBUS. Connect VAC and VBUS if ACFET is not to be used. |
| 2 | ACDRV | AO | Charge pump output to drive external N-channel MOSFET (ACFET). Provides 6V above VBUS as gate drive when VAC is below ACOV threshold and above UVLO. Leave floating if external OVP is not used. |
| 3 | D+ | AIO | Positive line of the USB data line pair. D+/D- based USB host/charging port detection. |
| 4 | D- | AIO | Negative line of the USB data line pair. D+/D- based USB host/charging port detection. |
| 5 | STAT | DO | Open-drain interrupt output. Connect the STAT pin to a logic rail via 10-kΩ resistor. Indicates charger status. |
| 6 | OTG | DI | Boost mode enable pin. When pulled HIGH, boost mode is enabled. Cannot be floating. |
| 7 | PG | DO | Open drain active low power good indicator. Connect to pull up rail through 10 kOhm resistor. |
| 8 | ILIM | AI | Sets the input current limit when adapter is detected as unknown. IINDPM = K_ILIM/R_ILIM. Range 500 mA - 3200 mA. |
| 9 | CE | DI | Charge enable pin. When driven LOW, battery charging is enabled. |
| 10 | ICHG | AI | Sets the charge current limit via a resistor from ICHG pin to ground. ICHG = K_ICHG/R_ICHG. Range 300 mA - 3000 mA. |
| 11 | TS | AI | Battery temperature qualification voltage input. Connect a negative temperature coefficient thermistor (NTC). Program temperature window with a resistor divider from REGN to TS to GND. |
| 12 | VSET | AI | VSET pin sets default battery charge voltage. Program battery regulation voltage with a resistor pull-down from VSET to GND. |
| 13 | BAT | P | Battery connection point to the positive terminal of the battery pack. Internal current sensing resistor is connected between SYS and BAT. |
| 14 | BAT | P | Battery connection point to the positive terminal of the battery pack. Internal current sensing resistor is connected between SYS and BAT. |
| 15 | SYS | P | System output connection point. The internal current sensing resistor is connected between SYS and BAT. Connect a 10 µF (min) capacitor close to the SYS pin. |
| 16 | SYS | P | System output connection point. The internal current sensing resistor is connected between SYS and BAT. Connect a 10 µF (min) capacitor close to the SYS pin. |
| 17 | GND | P | Power ground and signal ground |
| 18 | GND | P | Power ground and signal ground |
| 19 | SW | P | Switching node connecting to output inductor. Internally connected to the source of the n-channel HSFET and the drain of the n-channel LSFET. Connect the 0.047-µF bootstrap capacitor from SW to BTST. |
| 20 | SW | P | Switching node connecting to output inductor. Internally connected to the source of the n-channel HSFET and the drain of the n-channel LSFET. Connect the 0.047-µF bootstrap capacitor from SW to BTST. |
| 21 | BTST | P | PWM high side driver positive supply. Internally connected to the cathode of the boot-strap diode. Connect 0.047-uF bootstrap capacitor from SW to BTST. |
| 22 | REGN | P | PWM low side driver positive supply output. Internally, REGN is connected to the anode of the boot-strap diode. Connect a 4.7-µF (10-V rating) ceramic capacitor from REGN to analog GND. |
| 23 | PMID | P | Connected to the drain of the reverse blocking MOSFET (RBFET) and the drain of HSFET. Place a 10-µF capacitor on PMID to GND. |
| 24 | VBUS | P | Charger input voltage. The internal n-channel reverse block MOSFET (RBFET) is connected between VBUS and PMID with VBUS on source. Place a 1-uF ceramic capacitor from VBUS to GND. |
| — | Thermal Pad | P | Ground reference for the device that is also the thermal pad used to conduct heat from the device. Should be tied externally to a ground plane. |
BQ25616 Electrical Characteristics
VVBUS_UVLOZ < VVBUS < VVBUS_OV and VVBUS > VBAT + VSLEEP, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
| PARAMETER | PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT |
|---|---|---|---|---|---|---|
| QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS | QUIESCENT CURRENTS |
| I Q_BAT | Quiescent battery current (BAT, SYS, SW) | VBAT = 4.5V, VBUS floating or VBUS = 0V - 5V, SCL, SDA = 0V or 1.8V, T J < 85 °C, BATFET on. | 9.5 | 15 | μA | |
| I VBUS | Input current (VBUS) in buck mode when converter is switching | VBUS=5V, charge disabled, converter switching, ISYS = 0A | 2.3 | mA | ||
| I BST | Quiescent battery current (BAT, SYS, SW) in boost mode when converter is switching | VBAT = 4.5V, VBUS = 4.9V, boost mode enabled, converter switching, I VBUS = 0A | 2.4 | mA | ||
| VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY | VBUS / VBAT SUPPLY |
| V VBUS_OP | VBUS operating range | 4 | 13.5 | V | ||
| V VAC_UVLOZ | VAC rising for ACFET turnon, no battery | VAC rising | 3.55 | 3.85 | V | |
| V VAC_UVLO | VAC falling for ACFET turnoff, no battery | VAC falling | 3.25 | 3.55 | V | |
| V ACDRV | External ACFET gate drive voltage with minimum 8nF CGS | 10 | V | |||
| V VBUS_UVLOZ | VBUS rising for active bias, no battery | VBUS rising | 3.3 | 3.7 | V | |
| V VBUS_UVLO | VBUS falling to turnoff bias, no battery | VBUS falling | 3 | 3.3 | V | |
| V VBUS_PRESENT | VBUS to enable REGN | VBUS rising | 3.65 | 3.9 | V | |
| V VBUS_PRESENTZ | VBUS to disable REGN | VBUS falling | 3.15 | 3.4 | V | |
| V SLEEP | Enter Sleep mode threshold | VBUS falling, VBUS - VBAT, VBAT = 4V | 15 | 60 | 110 | mV |
| V SLEEPZ | Exit Sleep mode threshold | VBUS rising, VBUS - VBAT, VBAT = 4V | 115 | 220 | 340 | mV |
| V ACOV | VAC overvoltage rising threshold to turnoff ACFET and switching | VAC rising | 13.5 | 14.2 | 14.85 | V |
| V ACOV | VAC overvoltage falling threshold to turnon ACFET and switching | VAC falling, | 13 | 13.9 | 14.5 | V |
| V BAT_UVLOZ | BAT voltage for active bias, no VBUS | VBAT rising | 2.5 | V | ||
| V BAT_DPLZ | BAT depletion rising threshold to turn on BATFET | VBAT rising | 2.35 | 2.8 | V | |
| V BAT_DPL | BAT depletion falling threshold to turn off BATFET | VBAT falling | 2.18 | 2.62 | V | |
| V POORSRC | Bad adapter detection threshold | VBUS falling | 3.75 | 3.9 | 4.0 | V |
| POWER PATH MANAGEMENT | POWER PATH MANAGEMENT | POWER PATH MANAGEMENT | POWER PATH MANAGEMENT | POWER PATH MANAGEMENT | POWER PATH MANAGEMENT | POWER PATH MANAGEMENT |
| V SYS_MIN | Typical minimum system regulation voltage | VBAT=3.2V < SYS_MIN = 3.5V, ISYS = 0A | 3.5 | 3.65 | V | |
| V SYS_OVP | System overvoltage threshold | VREG = 4.35V, Charge disabled, ISYS = 0A | 4.7 | V | ||
| R ON_RBFET | Blocking FET on-resistance | 45 | mΩ |
VVBUS_UVLOZ < VVBUS < VVBUS_OV and VVBUS > VBAT + VSLEEP, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| R ON_HSFET | High-side switching FET on-resistance | 62 | mΩ | |||
| R ON_LSFET | Low-side switching FET on-resistance | 71 | mΩ | |||
| V BATFET _ FWD | BATFET forward voltage in supplement mode | BAT discharge current 10mA, converter running | 30 | mV | ||
| BATTERY CHARGER | BATTERY CHARGER | BATTERY CHARGER | BATTERY CHARGER | BATTERY CHARGER | BATTERY CHARGER | BATTERY CHARGER |
| VREG = 4.1V, R VSET =10kΩ, T J = 0°C - 85°C | 4.0836 | 4.1 | 4.1164 | V | ||
| V REG_ACC | Charge voltage accuracy | VREG = 4.2V, R VSET >50kΩ, T J = 0°C - 85°C | 4.1832 | 4.2 | 4.2168 | V |
| VREG = 4.35V, R VSET <500Ω, T J = 0°C - 85°C | 4.3326 | 4.35 | 4.3674 | V | ||
| I CHG_RANGE | Typical charge current regulation range | 0 | 3 | A | ||
| ICHG=K ICHG /R ICHG, VBAT = 3.1V, T J = -40°C - 85°C | 639 | 677 | 715 | AxΩ | ||
| K ICHG | ICHG pin setting ratio | ICHG=K ICHG /R ICHG, VBAT = 3.8V, T J = -40°C - 85°C | 639 | 677 | 715 | AxΩ |
| R ICHG = 1100 Ω, VBAT = 3.1V or 3.8V, T J = -40°C - 85°C | 0.516 | 0.615 | 0.715 | A | ||
| I CHG_ACC | Fast charge current regulation accuracy | R ICHG = 562 Ω, VBAT = 3.1V or 3.8V, T J = -40°C - 85°C | 1.14 | 1.205 | 1.28 | A |
| R ICHG = 372 Ω, VBAT = 3.1V or 3.8V, T J = -40°C - 85°C | 1.715 | 1.82 | 1.89 | A | ||
| I PRECHG_RATIO | Precharge current accuracy | As percentage of ICHG, VBAT = 2.6V | 5 | % | ||
| R ICHG = 1100 Ω, VBAT = 2.6V, T J = -40°C - 85°C | 21 | 30 | 38 | mA | ||
| I PRECHG_ACC | Precharge current accuracy | R ICHG = 562 Ω, VBAT = 2.6V, T J = - 40°C - 85°C | 48 | 60 | 67 | mA |
| R ICHG = 372 Ω, VBAT = 2.6V, T J = - 40°C - 85°C | 76 | 90 | 97 | mA | ||
| I TERM_RATIO | Termination current accuracy | As percentage of ICHG, VBAT = 4.35V, (char, all codes) | 5 | % | ||
| R ICHG = 1100 Ω, VBAT = 4.35V, T J = 0°C - 85°C | 9 | 31 | 57 | mA | ||
| I TERM_ACC | Termination current accuracy | R ICHG = 562 Ω, VBAT = 4.35V, T J = 0°C - 85°C | 36 | 60 | 85 | mA |
| R ICHG = 372 Ω, VBAT = 4.35V, T J = 0°C - 85°C | 56 | 91 | 126 | mA | ||
| V BAT_SHORTZ | Battery short voltage rising threshold to start pre-charge | VBAT rising | 2.13 | 2.25 | 2.35 | V |
| V BAT_SHORT | Battery short voltage falling threshold to stop pre-charge | VBAT falling | 1.85 | 2 | 2.15 | V |
| I BAT_SHORT | Battery short trickle charging current | VBAT < V BAT_SHORTZ | 70 | 90 | 110 | mA |
| Battery LOWV rising threshold to start fast-charge | VBAT rising | 3 | 3.12 | 3.24 | V | |
| V BATLOWV | Battery LOWV falling threshold to stop fast-charge | VBAT falling | 2.7 | 2.8 | 2.9 | V |
| V RECHG | Battery recharge threshold | VBAT falling | 90 | 100 | 150 | mV |
| I SYS_LOAD | System discharge load current during SYSOVP | 30 | mA |
VVBUS_UVLOZ < VVBUS < VVBUS_OV and VVBUS > VBAT + VSLEEP, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| R ON_BATFET | Battery FET on-resistance | T J = -40°C - 85°C T = -40°C - 125°C | 19.5 19.5 | 26 30 | mΩ mΩ | |
| BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION | BATTERY OVERVOLTAGE PROTECTION |
| V | Battery overvoltage rising threshold | VBAT rising, as percentage of VREG | 103 | 104 | 105 | % |
| BAT_OVP | Battery overvoltage falling threshold | VBAT falling, as percentage of VREG | 101 | 102 | 103 | % |
| INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION | INPUT VOLTAGE / CURRENT REGULATION |
| V INDPM_ACC | Typical input voltage regulation accuracy | 4.171 | 4.3 | 4.429 | V | |
| V INDPM_TRACK | VINDPM threshold to track battery voltage | VBAT = 4.35V | 4.45 | 4.55 | 4.74 | V |
| I INDPM_ACC | Input current regulation accuracy | IINDPM = 500mA (T J =-40°C - 85°C) | 450 | 465 | 500 | mA |
| I INDPM_ACC | Input current regulation accuracy | IINDPM = 900mA (T J =-40°C-85°C) | 750 | 835 | 900 | mA |
| I INDPM_ACC | Input current regulation accuracy | IINDPM = 1500mA (T J =-40°C-85°C) | 1300 | 1390 | 1500 | mA |
| K ILIM | ILIM pin setting ratio | 459 | 478 | 500 | A x Ω | |
| D+ / D- DETECTION | D+ / D- DETECTION | D+ / D- DETECTION | D+ / D- DETECTION | D+ / D- DETECTION | D+ / D- DETECTION | D+ / D- DETECTION |
| V DP_SRC | D+ line source voltage | 500 | 600 | 700 | mV | |
| I DP_SRC | D+ line data contact detect current source | VD+ = 200 mV | 7 | 10 | 14 | μA |
| I DP_SINK | D+ line sink current | VD+ = 500 mV | 50 | 100 | 150 | μA |
| V DP_DAT_REF | D+ line data detect voltage | D+ pin Rising | 250 | 400 | mV | |
| V DP_LGC_LOW | D+ line logic low. | D+ pin Rising | 800 | mV | ||
| R DP_DWN | D+ line pull-down resistance | VD+ = 500 mV | 14.25 | 24.8 | kΩ | |
| I D+_LKG | Leakage current into D+ line | Pull up to 1.8 V | -1 | 1 | μA | |
| V DM_SRC | D- line source voltage | 500 | 600 | 700 | mV | |
| I DM_SINK | D- line sink current | VD- = 500 mV | 50 | 100 | 150 | μA |
| V DM_DAT_REF | D- line data detect voltage | D- pin Rising | 250 | 400 | mV | |
| R DM_DWN | D- line pull-down resistance | VD- = 500 mV | 14.25 | 24.8 | kΩ | |
| I D-_LKG | Leakage current into D- line | Pull up to 1.8 V | -1 | 1 | μA | |
| V D+ _2p8_hi | D+ High comparator threshold for 2.8V detection | D+ pin rising | 2.85 | 3 | 3.1 | V |
| V D+ _2p8_lo | D+ Low comparator threshold for 2.8V detection | D+ pin rising | 2.35 | 2.45 | 2.55 | V |
| V D+ _2p8 | D+ comparator threshold for non- standard adapter | 2.55 | 2.85 | V | ||
| V D- _2p8_hi | D- High comparator threshold for 2.8V detection | D- pin rising | 2.85 | 3 | 3.1 | V |
| V D- _2p8_lo | D- Low comparator threshold for 2.8V detection | D- pin rising | 2.35 | 2.45 | 2.55 | V |
| V D- _2p8 | D- comparator threshold for non- standard adapter | 2.55 | 2.85 | V | ||
| V D+ _2p0_hi | D+ High comparator threshold for 2.0V detection | D+ pin rising | 2.15 | 2.25 | 2.35 | V |
| V D+ _2p0_lo | D+ Low comparator threshold for 2.0V detection | D+ pin rising | 1.6 | 1.7 | 1.85 | V |
| V D+ _2p0 | D+ comparator threshold for non- standard adapter | 1.85 | 2.15 | V | ||
| V D- _2p0_hi | D- High comparator threshold for 2.0V detection | D- pin rising | 2.15 | 2.25 | 2.35 | V |
VVBUS_UVLOZ < VVBUS < VVBUS_OV and VVBUS > VBAT + VSLEEP, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| V D- _2p0_lo | D- Low comparator threshold for 2.0V detection | D- pin rising | 1.6 | 1.7 | 1.85 | V |
| V D- _2p0 | D- comparator threshold for non- standard adapter | 1.85 | 2.15 | V | ||
| V D+ _1p2_hi | D+ High comparator threshold for 1.2V detection | D+ pin rising | 1.35 | 1.5 | 1.6 | V |
| V D+ _1p2_lo | D+ Low comparator threshold for 1.2V detection | D+ pin rising | 0.85 | 0.95 | 1.05 | V |
| V D+ _1p2 | D+ comparator threshold for non- standard adapter | 1.05 | 1.35 | V | ||
| V D- _1p2_hi | D- High comparator threshold for 1.2V detection | D- pin rising | 1.35 | 1.5 | 1.6 | V |
| V D- _1p2_lo | D- Low comparator threshold for 1.2V detection | D- pin rising | 0.85 | 0.95 | 1.05 | V |
| V D- _1p2 | D- comparator threshold for non- standard adapter | 1.05 | 1.35 | V | ||
| THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN | THERMAL REGULATION AND THERMAL SHUTDOWN |
| T REG | Junction temperature regulation accuracy | 110 | °C | |||
| T SHUT | Thermal Shutdown Rising threshold | Temperature Increasing | 150 | °C | ||
| T SHUT | Thermal Shutdown Falling threshold | Temperature Decreasing | 130 | °C | ||
| CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) | CHARGE MODE THERMISTOR COMPARATOR (JEITA 616J or HOT/COLD 616) |
| V T1_RISE% | TS pin voltage rising threshold, Charge suspended above this voltage. | As Percentage to REGN (0°C w/ 103AT) | 72.4 | 73.3 | 74.2 | % |
| V T1_FALL% | TS pin voltage falling threshold. Charge re-enabled to 20% of ICHG and VREG below this voltage. | As Percentage to REGN | 71.5 | 72 | 72.5 | % |
| V T2_RISE% | TS pin voltage rising threshold, Charge back to 20% of ICHG and VREG above this voltage (616J). | As Percentage to REGN (10°C w/ 103AT) | 67.75 | 68.25 | 68.75 | % |
| V T2_FALL% | TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage (616J) | As Percentage to REGN | 66.45 | 66.95 | 67.45 | % |
| V T3_FALL% | TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage (616J) | As Percentage to REGN (45°C w/ 103AT) | 44.25 | 44.75 | 45.25 | % |
| V T3_RISE% | TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. (616J) | As Percentage to REGN | 45.55 | 46.05 | 46.55 | % |
| V T5_FALL% | TS pin voltage falling threshold, charge suspended below this voltage. | As Percentage to REGN (60°C w/ 103AT) | 33.7 | 34.2 | 35.1 | % |
| V T5_RISE% | TS pin voltage rising threshold. Charge back to ICHG and 4.1V above this voltage. | As Percentage to REGN | 35 | 35.5 | 36 | % |
| V T1_RISE_HC% | TS pin voltage rising threshold. Charge suspended above this voltage. (616) | As Percentage to REGN (0°C w/ 103AT) | 72.4 | 73.3 | 74.2 | % |
| V T1_FALL_HC% | TS pin voltage falling threshold. Charge back to ICHG and VREG below this voltage. (616) | As Percentage to REGN | 71 | 72 | 73 | % |
VVBUS_UVLOZ < VVBUS < VVBUS_OV and VVBUS > VBAT + VSLEEP, TJ = -40°C to +125°C, and TJ = 25°C for typical values (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| V T3_FALL_HC% | TS pin voltage falling threshold. Charge suspended below this voltage. (616) | As Percentage to REGN (45°C w/ 103AT) | 44.25 | 44.75 | 45.25 | % |
| V T3_RISE _HC% | TS pin voltage rising threshold. Charge back to ICHG and VREG above this voltage. (616) | As Percentage to REGN | 45.55 | 46.05 | 46.55 | % |
| BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) | BOOST MODE THERMISTOR COMPARATOR (HOT/COLD) |
| V BCOLD_RISE% | TS pin voltage rising threshold, boost mode is suspended above this voltage. | As Percentage to REGN (-19.5°C w/ 103AT) | 79.5 | 80 | 80.5 | % |
| V BCOLD_FALL% | TS pin voltage falling threshold | As Percentage to REGN (0°C w/ 103AT) | 72 | % | ||
| V BHOT_FALL% | TS pin voltage threshold. boost mode is suspended below this voltage. | As Percentage to REGN, (64°C w/ 103AT) | 30.2 | 31.2 | 32.2 | % |
| V BHOT_RISE% | TS pin voltage rising threshold | As Percentage to REGN, (45°C w/ 103AT) | 44 | % | ||
| CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) | CHARGE OVERCURRENT COMPARATOR (CYCLE-BY-CYCLE) |
| I HSFET_OCP | HSFET cycle-by-cycle overcurrent threshold | 5.2 | 8.0 | A | ||
| SWITCHING CONVERTER | SWITCHING CONVERTER | SWITCHING CONVERTER | SWITCHING CONVERTER | SWITCHING CONVERTER | SWITCHING CONVERTER | SWITCHING CONVERTER |
| F SW | PWM switching frequency | Oscillator frequency | 1.32 | 1.5 | 1.68 | MHz |
| D MAX | Maximum PWM Duty Cycle | 97 | % | |||
| BOOST MODE CONVERTER | BOOST MODE CONVERTER | BOOST MODE CONVERTER | BOOST MODE CONVERTER | BOOST MODE CONVERTER | BOOST MODE CONVERTER | BOOST MODE CONVERTER |
| V BATLOWV_OTG | Battery voltage exiting boost mode | V VBAT falling | 2.6 | 2.8 | 2.9 | V |
| Battery voltage entering boost mode | V VBAT rising | 2.9 | 3.0 | 3.15 | V | |
| V BST_ACC | Boost mode voltage regulation accuracy | IVBUS = 0A, BOOST_V = 5V | 4.85 | 5 | 5.15 | V |
| I BST_ACC | Boost mode current regulation accuracy | 1.2 | 1.4 | 1.6 | A | |
| I SYS_OCP_Q4 | Boost mode battery discharge current clamp on BATFET Q4 | 9 | 10 | A | ||
| REGN LDO | REGN LDO | REGN LDO | REGN LDO | REGN LDO | REGN LDO | REGN LDO |
| V REGN | REGN LDO output voltage | V VBUS = 5V, I REGN = 20mA | 4.58 | 4.7 | 4.8 | V |
| V VBUS = 9V, I REGN = 20mA | 5.6 | 6 | 6.5 | V | ||
| I REGN | REGN LDO current limit | V VBUS = 5V, V REGN = 3.8V | 50 | mA | ||
| LOGIC INPUT PIN | LOGIC INPUT PIN | LOGIC INPUT PIN | LOGIC INPUT PIN | LOGIC INPUT PIN | LOGIC INPUT PIN | LOGIC INPUT PIN |
| V IH | Input high threshold level (/CE) | 1.3 | V | |||
| V IL | Input low threshold level (/CE) | 0.4 | V | |||
| I IN_BIAS | High-level leakage current (/CE) | Pull up rail 1.8V | 1 | μA | ||
| LOGIC OUTPUT PIN | LOGIC OUTPUT PIN | LOGIC OUTPUT PIN | LOGIC OUTPUT PIN | LOGIC OUTPUT PIN | LOGIC OUTPUT PIN | LOGIC OUTPUT PIN |
| V OL | Output low threshold level (STAT, /PG) | Sink current = 5mA | 0.4 | V | ||
| I OUT_BIAS | High-level leakage current (STAT, /PG) | Pull up rail 1.8V | 1 | μA |
BQ25616 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| Voltage | VAC (converter not switching) | -2 | 30 | V |
| Voltage | VBUS (converter not switching) | -2 | 22 | V |
| Voltage | PMID (converter not switching) | -0.3 | 22 | V |
| Voltage | SW | -0.3 | 16 | V |
| Voltage | BAT, SYS (converter not switching) | -0.3 | 7 | V |
| Voltage | BTST | -0.3 | 22 | V |
| Voltage | ACDRV | -0.3 | 40 | V |
| Voltage | D+. D-, STAT, OTG, PG, ILIM, CE, ICHG, TS, VSET | -0.3 | 7 | V |
| Output Sink Current | STAT, PG | 6 | mA | |
| T J | Junction temperature | -40 | 150 | °C |
| T stg | Storage temperature | -55 | 150 | °C |
BQ25616 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
| MIN | NOM | MAX | UNIT | ||
|---|---|---|---|---|---|
| V VBUS | Input voltage | 4 | 13.5 | V | |
| V BAT | Battery voltage | 4.35 | V | ||
| I VBUS | Input current | 3.2 | A | ||
| I SW | Output current (SW) | 3.2 | A | ||
| I BAT | Fast charging current | 3 | A | ||
| I BAT | RMS discharge current | 6 | A | ||
| T A | Ambient temperature | -40 | 85 | °C |
BQ25616 Thermal Information
| THERMAL METRIC (1) | THERMAL METRIC (1) - (1) ) | BQ25616/BQ25616J RTW (WQFN) - 24 Pins | UNIT |
|---|---|---|---|
| R θJA | Junction-to-ambient thermal resistance (JEDEC | 31.9 | °C/W |
| R θJC(top) | Junction-to-case (top) thermal resistance | 27 | °C/W |
| R θJB | Junction-to-board thermal resistance | 9.2 | °C/W |
| Ψ JT | Junction-to-top characterization parameter | 0.4 | °C/W |
| Ψ JB | Junction-to-board characterization parameter | 9.2 | °C/W |
BQ25616 Typical Application
A typical application consists of the device configured as a stand-alone power path management device and a single cell battery charger for Li-ion and Li-polymer batteries used in a wide range of smart phones and other portable devices. It integrates an input reverse-block FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET Q4) between the system and battery. The device also integrates a bootstrap diode for the high-side gate drive.
External ACFET is optional. When external OVP is not used, short the VBUS and VAC pins and allow the ACDRV pin to float.
BQ25616 Ordering Information
| PART NUMBER | PACKAGE | BODY SIZE (NOM) |
|---|---|---|
| BQ25616/616J | WQFN (24) | 4.00 mm × 4.00 mm |
For all available packages, see the orderable addendum at the end of the data sheet.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| BQ25616/616J | Texas Instruments | — |
| BQ25616/J | Texas Instruments | — |
| BQ25616J | Texas Instruments | WQFN (24) |
| BQ25616JRTWR | Texas Instruments | — |
| BQ25616JRTWR.A | Texas Instruments | — |
| BQ25616JRTWT | Texas Instruments | — |
| BQ25616JRTWT.A | Texas Instruments | — |
| BQ25616RTWR | Texas Instruments | 24-WFQFN Exposed Pad |
| BQ25616RTWR.A | Texas Instruments | — |
| BQ25616RTWT | Texas Instruments | |
| BQ25616RTWT.A | Texas Instruments | — |
More datasheets
Ask your AI agent about the BQ25616
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the BQ25616 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.