Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

BQ25185DLHR.A

Standalone Linear Battery Charger with Power Path

The BQ25185DLHR.A is a standalone linear battery charger with power path from Texas Instruments. View the full BQ25185DLHR.A datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

BQ25185DLHR.A shares its datasheet with BQ25185, whose page lists every part number it covers.

Official BQ25185DLHR.A datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Standalone Linear Battery Charger with Power Path

BQ25185DLHR.A Key Specifications

ParameterValue
Battery ChemistryMulti-Chemistry
Battery Pack Voltage3.6V, 3.65V, 4.02V, 4.1V, 4.2V, 4.35V, 4.4V
Charge Current (Max)1A
Current - ChargingConstant - Programmable
Fault ProtectionOver Current, Over Temperature, Over-Under Voltage, Short Circuit
Height800 µm
Length2.2 mm
Lifecycle StatusProduction (Last Updated: 1 day ago)
Manufacturer Lifecycle StatusACTIVE (Last Updated: 1 day ago)
Mounting TypeSurface Mount
Number of Cells1
Number of Pins10
Operating Temperature-40°C ~ 125°C (TJ)
Package / Case10-WFDFN Exposed Pad
PackagingMouseReel
Programmable FeaturesCurrent, Timer, Voltage
RoHSCompliant
Standard Pack Qty3000
Supplier Device Package10-WSON (2.2x2)
Thickness750 µm
Input Voltage (Max)18V
Width2 mm

BQ25185DLHR.A Overview

Part: BQ25185 (BQ25185DLHR) — Texas Instruments

Type: Standalone Linear Battery Charger with Power Path

Description: 1-cell, 1 A standalone linear battery charger for Li-ion, Li-poly and LiFePO4 with power path (4.5 V regulated SYS), 3.125 A system discharge support, battery-tracking VINDPM, factory mode and 25 V input tolerance.

Operating Conditions:

  • Input voltage (VIN) recommended: 2.7–5.5 V; input operating range per Electrical Characteristics: 3.6–18 V
  • Battery voltage range: 2.2–4.6 V
  • Operating junction temperature: -40 to 125 °C
  • Input current up to 1.1 A; battery discharge current up to 3.125 A

Absolute Maximum Ratings:

  • IN input voltage: -0.3 to 25 V
  • All other pins: -0.3 to 5.5 V
  • Input current (DC, IN): 1.1 A
  • SYS discharge current (DC): 3.125 A
  • STAT1/STAT2 sink current: 20 mA
  • Junction temperature: -40 to 150 °C
  • Storage temperature: -65 to 150 °C

Key Specs:

  • Input quiescent current (charge enabled, ICHG = 0): 0.75 mA typ, 1 mA max
  • Battery quiescent current (VIN < VUVLO, 0–85 °C): 4 μA typ, 5 μA max
  • Battery discharge current in factory mode (0–85 °C): 3.2 μA typ, 5 μA max
  • Sleep mode input current (VIN = 3.6 V, VBAT = 3.7 V): 30 μA typ
  • SYS regulation voltage: 4.5 V typ, ±2% accuracy (VIN = 5 V, VBAT = 3.6 V, RSYS = 100 Ω)
  • Battery charge voltage regulation: 3.6–4.4 V, ±0.5% accuracy
  • Charge current range: 5–1000 mA; ICHG = KISET/RISET (KISET = 300 AΩ typ); ±10% accuracy for fast charge current ≥ 40 mA
  • Precharge current: 20% of ICHG; termination current: 10% of ICHG
  • Battery FET RON: 115 mΩ typ, 140 mΩ max (VBAT = 4.5 V, IBAT = 400 mA)
  • Input FET RON: 330 mΩ typ, 470 mΩ max (VIN = 5 V, IIN = 1 A)
  • VIN overvoltage threshold: 18.5 V typ (18–19 V)
  • Thermal regulation: 100 °C typ; thermal shutdown rising: 150 °C typ
  • RθJA: 68.3 °C/W

Features:

  • 1 A linear charger; ILIM/VSET pin sets battery regulation voltage (3.6, 3.65, 4.02, 4.1, 4.2, 4.35 or 4.4 V) and input current limit (100, 500 or 1100 mA)
  • ISET pin sets charge current from 5 mA to 1 A
  • Power path management with regulated 4.5 V SYS and USB suspend support
  • Battery-tracking VINDPM and dynamic power path management for weak adapters
  • Single pushbutton (TS/MR) input for factory mode entry and manual reset; NTC thermistor monitoring
  • Protections: input OVP, BUVLO, BATSC, BATOCP, ILIM, TREG/TSHUT, TS, safety timer, system short and overvoltage, ISET and ILIM/VSET short/open
  • Open-drain status outputs (STAT1, STAT2) and active-low charge enable (CE)
  • HBM ±2500 V, CDM ±1500 V ESD ratings

Applications:

  • TWS headset and charging case
  • Smart glasses, AR and VR
  • Smart watches and other wearables
  • Retail automation and payment
  • Building automation

Package:

  • DLH WSON-10, 2.2 mm × 2.0 mm

BQ25185DLHR.A Features

  • 1A linear battery charger
  • -3.0V to 18V input voltage operating range
  • -25V tolerant input voltage
  • -External resistor programmable operation
  • ILIM/VSET pin sets battery regulation voltage to 3.6V, 3.65V, 4.02V, 4.1V, 4.2V, 4.35V, or 4.4V
  • ILIM/VSET pin sets input current limit to 100mA, 500mA, or 1100mA
  • ISET pin sets charge current from 5mA to 1A
  • -Supports Li-ion, Li-poly, and LiFePO 4 chemistries
  • -115mΩ battery FET on-resistance
  • -Supports up to 3.125A discharge current for high system loads
  • Power path management for powering the system and charging the battery
  • -Regulated system voltage (SYS) at 4.5V
  • -Configurable input current limit
  • -Supports USB suspend mode
  • -Battery tracking input voltage dynamic power management (VINDPM) for high-impedance input sources
  • -Dynamic power path management optimizes charging from weak adapters
  • Ultra-low quiescent current
  • -4μA in battery-only mode
  • -30μA input adapter IQ in sleep mode
  • -3.2μA battery discharge current in factory mode
  • Integrated fault protection
  • -Input overvoltage protection (VIN_OVP)
  • -Battery undervoltage protection (BUVLO)
  • -Battery short protection (BATSC)
  • -Battery overcurrent protection (BATOCP)
  • -Input current limit protection (ILIM)
  • -Thermal regulation (TREG) and thermal shutdown (TSHUT)
  • -Battery thermal fault protection (TS)
  • -Safety timer fault
  • -System short protection
  • -System overvoltage protection
  • -Short and open protection on the ISET and ILIM/VSET pins

BQ25185DLHR.A Applications

BQ25185DLHR.A Pin Configuration

Figure 4-1. DLH Package 10-Pin WSON (Top View)

Table 4-1. Pin Functions

PIN - NAMEPIN - NO.TYPE (1)DESCRIPTION
IN10PDC input power supply. Connect IN to the external DC supply. Bypass IN to GND with at least 1μF of capacitance using a ceramic capacitor.
SYS1PRegulated system output. Connect at least a 10μF ceramic capacitor (at least 1μF of capacitance after DC bias derating) from SYS to GND as close as possible to the SYS and GND pins.
BAT2PBattery connection. Connect BAT to the positive terminal of the battery. Bypass BAT to GND with at least 1μF of capacitance using a ceramic capacitor.
GND5-Ground connection. Connect to the ground plane of the circuit.
ILIM/VSET7I/OInput current limit and battery regulation voltage program input. See also Section 8.3.6 ILIM/VSET Control.
ISET8I/OFast charge current program input. An RC is recommended for low charge current values. Using only one resistor on the ISET pin is preferred. See also Section 8.1.1.4 ISET Pin Detection.
STAT19OOpen-drain status output. Can be pulled up with a 1kΩ to 20kΩ resistor. Typical pull-up voltage = 1.8V. Maximum pull-up voltage = 5V. See also Section 8.3.10 Status Pins. Can be left floating if unused.
TS/MR6I/OManual reset input and NTC thermistor input. TS/MR is a general-purpose input that must be held low for longer than t LPRESS to enter factory mode. TS/MR can be driven by a momentary pushbutton or a MOSFET. The TS/MR pin can also have an NTC thermistor connected to the TS/MR pin. See also Section 8.3.9 External NTC Monitoring (TS).
CE4ICharge enable active-low input. Connect CE to a high logic level to disable charging. Connect CE to a low logic level to enable charging.
STAT23OOpen-drain status output. Can be pulled up with a 1kΩ to 20kΩ resistor. Typical pull-up voltage = 1.8V. Maximum pull-up voltage = 5V. See also Section 8.3.10 Status Pins. Can be left floating if unused.

Table 4-1. Pin Functions

BQ25185DLHR.A Electrical Characteristics

VIN = 5 V, V BAT = 3.6 V. -40°C < T J < 125°C unless otherwise noted. Typical data at TJ = 25°C

PARAMETERPARAMETERTEST CONDITIONSMINTYPMAXUNIT
INPUT CURRENTSINPUT CURRENTSINPUT CURRENTSINPUT CURRENTSINPUT CURRENTSINPUT CURRENTSINPUT CURRENTS
I Q_INInput supply quiescent currentV BAT = 3.6V, V IN = 5V, Charge enabled, I CHG = 0mA, SYSREG = 4.5V0.751mA
I SLEEP_INSleep mode input currentV IN = 3.6V, V BAT = 3.7V30μA
I Q_BATBattery quiescent currentV IN < V UVLO , V BAT = 3.6V, 0°C < T J < 85°C45μA
I BAT_FACTBattery discharge current in factory modeV BAT = 3.6V, 0°C < T J < 85°C3.25μA
POWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUTPOWER-PATH MANAGEMENT AND INPUT
V IN_OPInput voltage operating range3.618V
V IN_UVLOZExit input undervoltage lockoutV IN rising3V
V IN_UVLOEnter input undervoltage lockoutV IN falling2.7V
V IN_LOWVV IN threshold to start chargingV IN rising33.15V
V IN_LOWVZV IN threshold to stop chargingV IN falling2.953.1V
V IN_PORZV IN threshold to enter factory modeV IN falling1.091.31.66V
V SLEEPZExit sleep mode thresholdV IN rising, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 1122152188mV
V SLEEPZExit sleep mode thresholdV IN rising, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 0168208262mV
V SLEEPEnter sleep mode thresholdV IN falling, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 182mV
V SLEEPEnter sleep mode thresholdV IN falling, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 082mV
V SLEEPEnter sleep mode thresholdV IN falling, V IN - V BAT , V BAT = 4V82mV
V SLEEPZExit sleep mode thresholdV IN rising, V IN - V BAT , V BAT = 4V110152188mV
V IN_OVPV IN overvoltage rising thresholdV IN rising1818.519V
V IN_OVP_HYSV IN overvoltage hysteresisV IN falling500mV
I BAT_OCPBATOCP (reverse OCP only)V BAT = 4V3.13A
I BAT_OCPACCBATOCP accuracyI BAT = 3.125A, T J = 27°C18%
V BSUP1Enter supplement mode thresholdV BAT = 3.6V, V BAT > V BUVLO , V SYS < V BAT - V BSUP140mV
V BSUP2Exit supplement mode thresholdV BAT > V BUVLO , V SYS > V BAT - V BSUP220mV
V IN = 5V, ILIM = 100mA809098mA
ILIMInput current limitV IN = 5V, ILIM = 500mA450475498mA
V IN = 5V, ILIM = 1050mA99510501100mA
V INDPMV IN threshold when input current is reducedRACKV BAT + V INDPM_TV
V INDPM_TRACKV IN threshold offset for when input current is reduced and when V BAT > 3.5VV INDPM target = V BAT + V INDPM_TRACK330mV

VIN = 5 V, V BAT = 3.6 V. -40°C < T J < 125°C unless otherwise noted. Typical data at TJ = 25°C

www.ti.com

BQ25185DLHR.A Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted) (1)

MINMAXUNIT
Input voltageIN-0.325V
VoltageAll other pins-0.35.5V
Input current (DC)IN1.1A
SYS discharge current (DC)SYS3.125A
Output sink currentSTAT1, STAT220mA
T JJunction temperature-40150°C
T stgStorage temperature-65150°C

over operating free-air temperature range (unless otherwise noted)

MINNOMMAXUNIT
V BATBattery voltage range2.24.6V
V INInput voltage range2.75.5V
I INInput current range (IN to SYS)1.1A
I BATBattery discharge current (BAT to SYS)3.125A

BQ25185DLHR.A Thermal Information

THERMAL METRIC (1)BQ25185 DLH - 10UNIT
R θJAJunction-to-ambient thermal resistance (JEDEC (1) )68.3°C/W
R θJC(top)Junction-to-case (top) thermal resistance77.2°C/W
R θJBJunction-to-board thermal resistance34.7°C/W
Ψ JTJunction-to-top characterization parameter2.0°C/W
Ψ JBJunction-to-board characterization parameter34.7°C/W
R θJC(bot)Junction-to-case (bottom) thermal resistance10.7°C/W

BQ25185DLHR.A Typical Application

A typical application of the BQ25185 is a standalone, single-cell Li-ion battery charger and power path manager for battery-powered systems such as smartwatches and wireless headsets. A battery thermistor can be connected to the TS/MR pin to allow the device to monitor battery temperature and control charging accordingly. The TS/MR pin can also be connected to a pushbutton that can be used to place the device into factory mode.

BQ25185DLHR.A Package Information

PART NUMBERPACKAGE (1)PACKAGE SIZE (2)BODY SIZE (NOM)
BQ25185DLH (WSON, 10)2.2mm × 2.0mm2.2mm × 2.0mm
  • (1) For more information, see Section 10.
  • (2) The package size (length × width) is a nominal value and includes pins, where applicable.

Simplified Schematic

The battery is charged using a standard Li-ion or LiFePO 4 charging profile with three phases: precharge, constant current, and constant voltage. Thermal regulation provides the maximum charge current while managing the device temperature. The charger is optimized for battery-to-battery charging with 3V minimum input voltage operation and can withstand 25V absolute maximum line transients. The device integrates a single pushbutton input to reduce the total design footprint.

www.ti.com

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
BQ25185Texas Instruments—
BQ25185DLHRTexas Instruments10-WFDFN Exposed Pad

More datasheets

All Texas Instruments datasheets (2,605)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the BQ25185DLHR.A

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the BQ25185DLHR.A run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.