BQ25185DLHR
Standalone Linear Battery Charger with Power PathThe BQ25185DLHR is a standalone linear battery charger with power path from Texas Instruments. View the full BQ25185DLHR datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
BQ25185DLHR shares its datasheet with BQ25185, whose page lists every part number it covers.
Official BQ25185DLHR datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Standalone Linear Battery Charger with Power Path
Package
10-WFDFN Exposed Pad
Lifecycle
Production (Last Updated: 1 day ago)
BQ25185DLHR Key Specifications
| Parameter | Value |
|---|---|
| Battery Chemistry | Multi-Chemistry |
| Battery Pack Voltage | 3.6V, 3.65V, 4.02V, 4.1V, 4.2V, 4.35V, 4.4V |
| Charge Current (Max) | 1A |
| Current - Charging | Constant - Programmable |
| Fault Protection | Over Current, Over Temperature, Over-Under Voltage, Short Circuit |
| Height | 800 µm |
| Length | 2.2 mm |
| Lifecycle Status | Production (Last Updated: 1 day ago) |
| Manufacturer Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Number of Cells | 1 |
| Number of Pins | 10 |
| Operating Temperature | -40°C ~ 125°C (TJ) |
| Package / Case | 10-WFDFN Exposed Pad |
| Packaging | MouseReel |
| Programmable Features | Current, Timer, Voltage |
| RoHS | Compliant |
| Standard Pack Qty | 3000 |
| Supplier Device Package | 10-WSON (2.2x2) |
| Thickness | 750 µm |
| Input Voltage (Max) | 18V |
| Width | 2 mm |
BQ25185DLHR Overview
Part: BQ25185 (BQ25185DLHR) — Texas Instruments
Type: Standalone Linear Battery Charger with Power Path
Description: 1-cell, 1 A standalone linear battery charger for Li-ion, Li-poly and LiFePO4 with power path (4.5 V regulated SYS), 3.125 A system discharge support, battery-tracking VINDPM, factory mode and 25 V input tolerance.
Operating Conditions:
- Input voltage (VIN) recommended: 2.7–5.5 V; input operating range per Electrical Characteristics: 3.6–18 V
- Battery voltage range: 2.2–4.6 V
- Operating junction temperature: -40 to 125 °C
- Input current up to 1.1 A; battery discharge current up to 3.125 A
Absolute Maximum Ratings:
- IN input voltage: -0.3 to 25 V
- All other pins: -0.3 to 5.5 V
- Input current (DC, IN): 1.1 A
- SYS discharge current (DC): 3.125 A
- STAT1/STAT2 sink current: 20 mA
- Junction temperature: -40 to 150 °C
- Storage temperature: -65 to 150 °C
Key Specs:
- Input quiescent current (charge enabled, ICHG = 0): 0.75 mA typ, 1 mA max
- Battery quiescent current (VIN < VUVLO, 0–85 °C): 4 μA typ, 5 μA max
- Battery discharge current in factory mode (0–85 °C): 3.2 μA typ, 5 μA max
- Sleep mode input current (VIN = 3.6 V, VBAT = 3.7 V): 30 μA typ
- SYS regulation voltage: 4.5 V typ, ±2% accuracy (VIN = 5 V, VBAT = 3.6 V, RSYS = 100 Ω)
- Battery charge voltage regulation: 3.6–4.4 V, ±0.5% accuracy
- Charge current range: 5–1000 mA; ICHG = KISET/RISET (KISET = 300 AΩ typ); ±10% accuracy for fast charge current ≥ 40 mA
- Precharge current: 20% of ICHG; termination current: 10% of ICHG
- Battery FET RON: 115 mΩ typ, 140 mΩ max (VBAT = 4.5 V, IBAT = 400 mA)
- Input FET RON: 330 mΩ typ, 470 mΩ max (VIN = 5 V, IIN = 1 A)
- VIN overvoltage threshold: 18.5 V typ (18–19 V)
- Thermal regulation: 100 °C typ; thermal shutdown rising: 150 °C typ
- RθJA: 68.3 °C/W
Features:
- 1 A linear charger; ILIM/VSET pin sets battery regulation voltage (3.6, 3.65, 4.02, 4.1, 4.2, 4.35 or 4.4 V) and input current limit (100, 500 or 1100 mA)
- ISET pin sets charge current from 5 mA to 1 A
- Power path management with regulated 4.5 V SYS and USB suspend support
- Battery-tracking VINDPM and dynamic power path management for weak adapters
- Single pushbutton (TS/MR) input for factory mode entry and manual reset; NTC thermistor monitoring
- Protections: input OVP, BUVLO, BATSC, BATOCP, ILIM, TREG/TSHUT, TS, safety timer, system short and overvoltage, ISET and ILIM/VSET short/open
- Open-drain status outputs (STAT1, STAT2) and active-low charge enable (CE)
- HBM ±2500 V, CDM ±1500 V ESD ratings
Applications:
- TWS headset and charging case
- Smart glasses, AR and VR
- Smart watches and other wearables
- Retail automation and payment
- Building automation
Package:
- DLH WSON-10, 2.2 mm × 2.0 mm
BQ25185DLHR Features
- 1A linear battery charger
- -3.0V to 18V input voltage operating range
- -25V tolerant input voltage
- -External resistor programmable operation
- ILIM/VSET pin sets battery regulation voltage to 3.6V, 3.65V, 4.02V, 4.1V, 4.2V, 4.35V, or 4.4V
- ILIM/VSET pin sets input current limit to 100mA, 500mA, or 1100mA
- ISET pin sets charge current from 5mA to 1A
- -Supports Li-ion, Li-poly, and LiFePO 4 chemistries
- -115mΩ battery FET on-resistance
- -Supports up to 3.125A discharge current for high system loads
- Power path management for powering the system and charging the battery
- -Regulated system voltage (SYS) at 4.5V
- -Configurable input current limit
- -Supports USB suspend mode
- -Battery tracking input voltage dynamic power management (VINDPM) for high-impedance input sources
- -Dynamic power path management optimizes charging from weak adapters
- Ultra-low quiescent current
- -4μA in battery-only mode
- -30μA input adapter IQ in sleep mode
- -3.2μA battery discharge current in factory mode
- Integrated fault protection
- -Input overvoltage protection (VIN_OVP)
- -Battery undervoltage protection (BUVLO)
- -Battery short protection (BATSC)
- -Battery overcurrent protection (BATOCP)
- -Input current limit protection (ILIM)
- -Thermal regulation (TREG) and thermal shutdown (TSHUT)
- -Battery thermal fault protection (TS)
- -Safety timer fault
- -System short protection
- -System overvoltage protection
- -Short and open protection on the ISET and ILIM/VSET pins
BQ25185DLHR Applications
BQ25185DLHR Pin Configuration
Figure 4-1. DLH Package 10-Pin WSON (Top View)
Table 4-1. Pin Functions
| PIN - NAME | PIN - NO. | TYPE (1) | DESCRIPTION |
|---|---|---|---|
| IN | 10 | P | DC input power supply. Connect IN to the external DC supply. Bypass IN to GND with at least 1μF of capacitance using a ceramic capacitor. |
| SYS | 1 | P | Regulated system output. Connect at least a 10μF ceramic capacitor (at least 1μF of capacitance after DC bias derating) from SYS to GND as close as possible to the SYS and GND pins. |
| BAT | 2 | P | Battery connection. Connect BAT to the positive terminal of the battery. Bypass BAT to GND with at least 1μF of capacitance using a ceramic capacitor. |
| GND | 5 | - | Ground connection. Connect to the ground plane of the circuit. |
| ILIM/VSET | 7 | I/O | Input current limit and battery regulation voltage program input. See also Section 8.3.6 ILIM/VSET Control. |
| ISET | 8 | I/O | Fast charge current program input. An RC is recommended for low charge current values. Using only one resistor on the ISET pin is preferred. See also Section 8.1.1.4 ISET Pin Detection. |
| STAT1 | 9 | O | Open-drain status output. Can be pulled up with a 1kΩ to 20kΩ resistor. Typical pull-up voltage = 1.8V. Maximum pull-up voltage = 5V. See also Section 8.3.10 Status Pins. Can be left floating if unused. |
| TS/MR | 6 | I/O | Manual reset input and NTC thermistor input. TS/MR is a general-purpose input that must be held low for longer than t LPRESS to enter factory mode. TS/MR can be driven by a momentary pushbutton or a MOSFET. The TS/MR pin can also have an NTC thermistor connected to the TS/MR pin. See also Section 8.3.9 External NTC Monitoring (TS). |
| CE | 4 | I | Charge enable active-low input. Connect CE to a high logic level to disable charging. Connect CE to a low logic level to enable charging. |
| STAT2 | 3 | O | Open-drain status output. Can be pulled up with a 1kΩ to 20kΩ resistor. Typical pull-up voltage = 1.8V. Maximum pull-up voltage = 5V. See also Section 8.3.10 Status Pins. Can be left floating if unused. |
Table 4-1. Pin Functions
BQ25185DLHR Electrical Characteristics
VIN = 5 V, V BAT = 3.6 V. -40°C < T J < 125°C unless otherwise noted. Typical data at TJ = 25°C
| PARAMETER | PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT |
|---|---|---|---|---|---|---|
| INPUT CURRENTS | INPUT CURRENTS | INPUT CURRENTS | INPUT CURRENTS | INPUT CURRENTS | INPUT CURRENTS | INPUT CURRENTS |
| I Q_IN | Input supply quiescent current | V BAT = 3.6V, V IN = 5V, Charge enabled, I CHG = 0mA, SYSREG = 4.5V | 0.75 | 1 | mA | |
| I SLEEP_IN | Sleep mode input current | V IN = 3.6V, V BAT = 3.7V | 30 | μA | ||
| I Q_BAT | Battery quiescent current | V IN < V UVLO , V BAT = 3.6V, 0°C < T J < 85°C | 4 | 5 | μA | |
| I BAT_FACT | Battery discharge current in factory mode | V BAT = 3.6V, 0°C < T J < 85°C | 3.2 | 5 | μA | |
| POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT | POWER-PATH MANAGEMENT AND INPUT |
| V IN_OP | Input voltage operating range | 3.6 | 18 | V | ||
| V IN_UVLOZ | Exit input undervoltage lockout | V IN rising | 3 | V | ||
| V IN_UVLO | Enter input undervoltage lockout | V IN falling | 2.7 | V | ||
| V IN_LOWV | V IN threshold to start charging | V IN rising | 3 | 3.15 | V | |
| V IN_LOWVZ | V IN threshold to stop charging | V IN falling | 2.95 | 3.1 | V | |
| V IN_PORZ | V IN threshold to enter factory mode | V IN falling | 1.09 | 1.3 | 1.66 | V |
| V SLEEPZ | Exit sleep mode threshold | V IN rising, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 1 | 122 | 152 | 188 | mV |
| V SLEEPZ | Exit sleep mode threshold | V IN rising, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 0 | 168 | 208 | 262 | mV |
| V SLEEP | Enter sleep mode threshold | V IN falling, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 1 | 82 | mV | ||
| V SLEEP | Enter sleep mode threshold | V IN falling, V IN - V BAT , V BAT = 4V, VINDPM_ACTIVE = 0 | 82 | mV | ||
| V SLEEP | Enter sleep mode threshold | V IN falling, V IN - V BAT , V BAT = 4V | 82 | mV | ||
| V SLEEPZ | Exit sleep mode threshold | V IN rising, V IN - V BAT , V BAT = 4V | 110 | 152 | 188 | mV |
| V IN_OVP | V IN overvoltage rising threshold | V IN rising | 18 | 18.5 | 19 | V |
| V IN_OVP_HYS | V IN overvoltage hysteresis | V IN falling | 500 | mV | ||
| I BAT_OCP | BATOCP (reverse OCP only) | V BAT = 4V | 3.13 | A | ||
| I BAT_OCPACC | BATOCP accuracy | I BAT = 3.125A, T J = 27°C | 18 | % | ||
| V BSUP1 | Enter supplement mode threshold | V BAT = 3.6V, V BAT > V BUVLO , V SYS < V BAT - V BSUP1 | 40 | mV | ||
| V BSUP2 | Exit supplement mode threshold | V BAT > V BUVLO , V SYS > V BAT - V BSUP2 | 20 | mV | ||
| V IN = 5V, ILIM = 100mA | 80 | 90 | 98 | mA | ||
| ILIM | Input current limit | V IN = 5V, ILIM = 500mA | 450 | 475 | 498 | mA |
| V IN = 5V, ILIM = 1050mA | 995 | 1050 | 1100 | mA | ||
| V INDPM | V IN threshold when input current is reduced | RACK | V BAT + V INDPM_T | V | ||
| V INDPM_TRACK | V IN threshold offset for when input current is reduced and when V BAT > 3.5V | V INDPM target = V BAT + V INDPM_TRACK | 330 | mV |
VIN = 5 V, V BAT = 3.6 V. -40°C < T J < 125°C unless otherwise noted. Typical data at TJ = 25°C
BQ25185DLHR Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
| MIN | MAX | UNIT | ||
|---|---|---|---|---|
| Input voltage | IN | -0.3 | 25 | V |
| Voltage | All other pins | -0.3 | 5.5 | V |
| Input current (DC) | IN | 1.1 | A | |
| SYS discharge current (DC) | SYS | 3.125 | A | |
| Output sink current | STAT1, STAT2 | 20 | mA | |
| T J | Junction temperature | -40 | 150 | °C |
| T stg | Storage temperature | -65 | 150 | °C |
BQ25185DLHR Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
| MIN | NOM | MAX | UNIT | ||
|---|---|---|---|---|---|
| V BAT | Battery voltage range | 2.2 | 4.6 | V | |
| V IN | Input voltage range | 2.7 | 5.5 | V | |
| I IN | Input current range (IN to SYS) | 1.1 | A | ||
| I BAT | Battery discharge current (BAT to SYS) | 3.125 | A |
BQ25185DLHR Thermal Information
| THERMAL METRIC (1) | BQ25185 DLH - 10 | UNIT | |
|---|---|---|---|
| R θJA | Junction-to-ambient thermal resistance (JEDEC (1) ) | 68.3 | °C/W |
| R θJC(top) | Junction-to-case (top) thermal resistance | 77.2 | °C/W |
| R θJB | Junction-to-board thermal resistance | 34.7 | °C/W |
| Ψ JT | Junction-to-top characterization parameter | 2.0 | °C/W |
| Ψ JB | Junction-to-board characterization parameter | 34.7 | °C/W |
| R θJC(bot) | Junction-to-case (bottom) thermal resistance | 10.7 | °C/W |
BQ25185DLHR Typical Application
A typical application of the BQ25185 is a standalone, single-cell Li-ion battery charger and power path manager for battery-powered systems such as smartwatches and wireless headsets. A battery thermistor can be connected to the TS/MR pin to allow the device to monitor battery temperature and control charging accordingly. The TS/MR pin can also be connected to a pushbutton that can be used to place the device into factory mode.
BQ25185DLHR Package Information
| PART NUMBER | PACKAGE (1) | PACKAGE SIZE (2) | BODY SIZE (NOM) |
|---|---|---|---|
| BQ25185 | DLH (WSON, 10) | 2.2mm × 2.0mm | 2.2mm × 2.0mm |
- (1) For more information, see Section 10.
- (2) The package size (length × width) is a nominal value and includes pins, where applicable.
Simplified Schematic
The battery is charged using a standard Li-ion or LiFePO 4 charging profile with three phases: precharge, constant current, and constant voltage. Thermal regulation provides the maximum charge current while managing the device temperature. The charger is optimized for battery-to-battery charging with 3V minimum input voltage operation and can withstand 25V absolute maximum line transients. The device integrates a single pushbutton input to reduce the total design footprint.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| BQ25185 | Texas Instruments | — |
| BQ25185DLHR.A | Texas Instruments | — |
More datasheets
Ask your AI agent about the BQ25185DLHR
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the BQ25185DLHR run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.