BQ25101H
Single-Cell Li-Ion Linear Battery ChargerThe BQ25101H is a single-cell li-ion linear battery charger from Texas Instruments. View the full BQ25101H datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
BQ25101H shares its datasheet with BQ25101, whose page lists every part number it covers.
Official BQ25101H datasheet (PDF) — the source this page was extracted from.
Manufacturer
Texas InstrumentsCategory
Single-Cell Li-Ion Linear Battery Charger
BQ25101H Key Specifications
| Parameter | Value |
|---|---|
| Battery Chemistry | Lithium Ion/Polymer |
| Battery Pack Voltage | 4.2V |
| Charge Current (Max) | 250mA |
| Contact Plating | Copper, Silver, Tin |
| Current - Charging | Constant - Programmable |
| Fault Protection | Over Temperature, Over Voltage, Short Circuit |
| Height | 500 µm |
| Lead Free | Lead Free |
| Length | 1 mm |
| Lifecycle Status | Production (Last Updated: 2 days ago) |
| Manufacturer Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Max Operating Temperature | 125 °C |
| Min Operating Temperature | 0 °C |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Number of Cells | 1 |
| Number of Cells | 1 |
| Number of Pins | 6 |
| Operating Supply Voltage | 28 V |
| Operating Temperature | 0°C ~ 125°C (TJ) |
| Output Current | 250 mA |
| Output Voltage | 4.2 V |
| Package / Case | 6-XFBGA, DSBGA |
| Packaging | MouseReel |
| Programmable Features | Current |
| RoHS | Compliant |
| Schedule B | 8542390000, 8542390000|8542390000|8542390000|8542390000|8542390000 |
| Standard Pack Qty | 250 |
| Supplier Device Package | 6-DSBGA |
| Thickness | 500 µm |
| Input Voltage (Max) | 6.45V |
| Width | 1.4 mm |
BQ25101H Overview
Part: bq25101 (bq2510x family: bq25100, bq25101, bq25100A, bq25100H, bq25101H, bq25100L) — Texas Instruments
Type: Single-Cell Li-Ion/Li-Pol Linear Battery Charger
Description: 250-mA linear Li-Ion battery charger with 30-V input rating and 6.5-V input overvoltage protection, 1-mA minimum termination current, ±1% charge voltage accuracy and a maximum of 75 nA battery leakage, in a 1.60 mm × 0.90 mm DSBGA package.
Operating Conditions:
- Supply voltage (IN): 3.5–28 V (operating range restricted by VDPM and VOVP: 4.45–6.45 V)
- Junction temperature: 0 to 125 °C
- Fast-charge current: 10–250 mA (RISET 0.54–13.5 kΩ)
Absolute Maximum Ratings:
- IN voltage: -0.3 to 30 V
- OUT, PRE-TERM, ISET, TS, CHG pin voltage: -0.3 to 7 V
- IN input current: 300 mA
- OUT continuous output current: 300 mA
- CHG sink current: 15 mA
- Junction temperature: -40 to 150 °C
- Storage temperature: -65 to 150 °C
Key Specs:
- Output regulation voltage (bq25100/101): 4.16 / 4.2 / 4.23 V (min/typ/max), TJ 0–125 °C, IOUT 0–250 mA, VIN = 5 V
- Variants: 4.30 V (bq25100A), 4.35 V (bq25100H/101H), 4.06 V (bq25100L, product preview)
- Hot regulation voltage (bq25100/101): 4.06 V typ (4.02–4.1 V)
- Battery leakage into OUT (VIN = 0 V): 75 nA max at 0–125 °C; 50 nA max at 0–85 °C
- Fast-charge current: IOUT = KISET/RISET, KISET = 135 AΩ typ
- UVLO exit: 3.3 V typ (3.15–3.45 V); OVP threshold: 6.67 V typ (6.52–6.82 V)
- Pre-charge to fast-charge threshold (VLOWV): 2.5 V typ (2.4–2.6 V); default pre-charge 20% and termination 10% of charge current
- Dropout (VIN–VOUT): 220 mV typ, 400 mV max at IOUT = 0.2 A
- Active supply current (ICC): 0.75 mA typ, 1 mA max (TTDM, VIN = 6 V); standby current 125 μA max
- Thermal resistance RθJA: 132.9 °C/W (YFP, 6 pins)
Features:
- ±1% charge voltage accuracy and ±10% charge current accuracy
- Adjustable termination and pre-charge thresholds via a single PRE-TERM resistor (bq25100 variants); minimum 1-mA termination current
- Input voltage dynamic power management (VIN-DPM)
- 125 °C thermal regulation and 150 °C thermal shutdown
- OUT short-circuit protection and ISET short detection
- JEITA-compliant operation via battery NTC (half fast-charge current at cold, reduced voltage at hot)
- Fixed 10-hour safety timer
- Termination and Timer Disable Mode (TTDM) for absent battery pack
- CHG status output (bq25101/101H)
Applications:
- Fitness accessories
- Smart watches
- Bluetooth headsets
- Low-power handheld devices
Package:
- DSBGA (6 pins), 1.60 mm × 0.90 mm (YFP)
BQ25101H Applications
- Fitness Accessories
- Smart Watches
- Bluetooth ® Headsets
- Low-Power Handheld Devices
1
The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at spacelimited portable applications. The high input voltage range with input overvoltage protection supports lowcost unregulated adapters.
The bq2510x has a single power output that charges the battery. A system load can be placed in parallel with the battery as long as the average system load does not keep the battery from charging fully during the 10 hour safety timer.
The battery is charged in three phases: conditioning, constant current and constant voltage. In all charge phases, an internal control loop monitors the IC junction temperature and reduces the charge current if an internal temperature threshold is exceeded.
The charger power stage and charge current sense functions are fully integrated. The charger function has high accuracy current and voltage regulation loops and charge termination. The pre-charge current and termination current threshold are programmed via an external resistor on the bq2510x. The fast charge current value is also programmable via an external resistor.
BQ25101H Pin Configuration
bq25100/100A/100H/100L
SPACING
BQ25101H Electrical Characteristics
Over junction temperature range 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)
| PARAMETER | TEST CONDITIONS | MIN | TYP | MAX | UNIT | |
|---|---|---|---|---|---|---|
| INPUT | ||||||
| UVLO | Undervoltage lock-out exit | V IN : 0 V → 4 V | 3.15 | 3.3 | 3.45 | V |
| V HYS_UVLO | Hysteresis on V UVLO_RISE falling | V IN : 4 V → 0 V; V UVLO_FALL = V UVLO_RISE - V HYS-UVLO | 250 | mV | ||
| V IN-DT | Input power good detection threshold is V OUT + V IN-DT | Input power good if V IN > V OUT + V IN-DT ; V OUT = 3.6 V; V IN : 3.5 V → 4 V | 15 | 60 | 130 | mV |
| V HYS-INDT | Hysteresis on V IN-DT falling | V OUT = 3.6 V; V IN : 4 V → 3.5 V | 31 | mV | ||
| t DGL(PG_PWR) | Deglitch time on exiting sleep | Time measured from V IN : 0 V → 5 V 1- μ s rise- time to charge enables; V OUT = 3.6 V | 29 | ms | ||
| t DGL(PG_NO-PWR) | Deglitch time on V HYS-INDT power down. Same as entering sleep. | Time measured from V IN : 5 V → 3.2 V 1- μ s fall- time to charge disables; V OUT = 3.6 V | 29 | ms | ||
| V OVP | Input over-voltage protection threshold | V IN : 5 V → 12 V | 6.52 | 6.67 | 6.82 | V |
| t DGL(OVP-SET) | Input over-voltage blanking time | V IN : 5 V → 12 V | 113 | μ s | ||
| V HYS-OVP | Hysteresis on OVP | V IN : 11 V → 5 V | 110 | mV | ||
| t DGL(OVP-REC) | Deglitch time exiting OVP | Time measured from V IN : 12 V → 5 V 1- μ s fall- time to charge enables | 450 | μ s | ||
| V IN-DPM | Low input voltage protection. Restricts lout at V IN-DPM | Limit input source current to 50 mA; V OUT = 3.5 V; R ISET = 1.35 k Ω | 4.25 | 4.31 | 4.37 | V |
| ISET SHORT CIRCUIT TEST | ISET SHORT CIRCUIT TEST | |||||
| R ISET_SHORT | Highest resistor value considered a fault (short). | R ISET : 540 Ω→ 250 Ω , Iout latches off; Cycle power to reset | 420 | 450 | Ω | |
| t DGL_SHORT | Deglitch time transition from ISET short to Iout disable | Clear fault by disconnecting IN or cycling (high / low) TS/BAT_EN | 1 | ms | ||
| I OUT_CL | Maximum OUT current limit regulation (Clamp) | V IN = 5 V; V OUT = 3.6 V; R ISET : 540 Ω→ 250 Ω ; I OUT latches off after t DGL-SHORT | 550 | 600 | 650 | mA |
| BATTERY SHORT PROTECTION | BATTERY SHORT PROTECTION | |||||
| V OUT(SC) | OUT pin short-circuit detection threshold/ precharge threshold | V OUT :3 V → 0.5 V; No deglitch | 0.75 | 0.8 | 0.85 | V |
| V OUT(SC-HYS) | OUT pin Short hysteresis | Recovery ≥ V OUT(SC) + V OUT(SC-HYS) ; Rising; No deglitch | 77 | mV | ||
| I OUT(SC) | Source current to OUT pin during short-circuit detection | 9 | 11 | 13 | mA | |
| QUIESCENT CURRENT | QUIESCENT CURRENT | |||||
| I | Battery current into OUT pin | V IN = 0 V; 0°C to 125°C | 75 | nA | ||
| OUT(PDWN) | V IN = 0 V; 0°C to 85°C | 50 | ||||
| I OUT(DONE) | OUT pin current, charging terminated | V IN = 6 V; V OUT > V OUT(REG) | 6 | μ A | ||
| I IN(STDBY) | Standby current into IN pin | TS = GND; V IN ≤ 6 V | 125 | μ A | ||
| I CC | Active supply current, IN pin | TS = open, V IN = 6 V; TTDM - no load on OUT pin; V OUT > V OUT(REG) ; IC enabled | 0.75 | 1 | mA | |
| BATTERY CHARGER FAST-CHARGE | BATTERY CHARGER FAST-CHARGE | |||||
| T J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100/101) | 4.16 | 4.2 | 4.23 | V | ||
| V OUT(REG) | T J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100A) | 4.26 | 4.3 | 4.33 | ||
| V OUT(REG) | Output voltage | T J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100H/101H) | 4.31 | 4.35 | 4.38 | |
| T J = -5°C to 55°C; I OUT = 10mA to 75 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100A) | 4.275 | 4.3 | 4.325 | |||
| V O_HT(REG) | Battery hot regulation voltage | V IN = 5.0 V; I OUT =10 mA to 250 mA; V TS-60°C ≤ V TS ≤ V TS-45°C (bq25100/101) | 4.02 | 4.06 | 4.1 | V |
| I OUT(RANGE) | Programmed output 'fast charge' current range | V IN = 5.0 V; I OUT =10 mA to 250 mA; V TS-60°C ≤ V TS ≤ V TS-45°C (bq25100H/101H) V OUT(REG) > V OUT > V LOWV ; V IN = 5 V; R ISET = 0.54 k Ω to 13.5 k Ω | 4.16 10 | 4.2 | 4.24 250 | mA |
SLUSBV8C -AUGUST 2014-REVISED NOVEMBER 2014
BQ25101H Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
| MIN | MAX | UNIT | |||
|---|---|---|---|---|---|
| Input voltage | IN (with respect to VSS) | -0.3 | 30 | V | |
| OUT (with respect to VSS) | -0.3 | 7 | V | ||
| PRE-TERM, ISET, TS, CHG (with respect to VSS) | -0.3 | 7 | V | ||
| Input current | IN | 300 | mA | ||
| Output current (continuous) | OUT | 300 | mA | ||
| Output sink current | CHG | 15 | mA | ||
| T J | Junction temperature | Junction temperature | -40 | 150 | °C |
BQ25101H Recommended Operating Conditions
| MIN | NOM | UNIT | ||
|---|---|---|---|---|
| V | IN voltage range | 3.5 | 28 | V |
| IN | IN operating voltage range, Restricted by V DPM and V OVP | 4.45 | 6.45 | V |
| I IN | Input current, IN pin | 250 | mA | |
| I OUT | Current, OUT pin | 250 | mA | |
| T J | Junction temperature | 0 | 125 | °C |
| R PRE-TERM | Programs precharge and termination current thresholds | 0.6 | 30 | k Ω |
| R ISET | Fast-charge current programming resistor | 0.54 | 13.5 | k Ω |
| R TS | 10k NTC thermistor range without entering BAT_EN or TTDM | 1.66 | 258 | k Ω |
BQ25101H Thermal Information
| THERMAL METRIC (1) | THERMAL METRIC (1) | bq25100 YFP (6 PINS) | UNIT |
|---|---|---|---|
| R θ JA | Junction-to-ambient thermal resistance | 132.9 | °C/W |
| R θ JCtop | Junction-to-case (top) thermal resistance | 1.3 | °C/W |
| R θ JB | Junction-to-board thermal resistance | 21.8 | °C/W |
| ψ JT | Junction-to-top characterization parameter | 5.6 | °C/W |
| ψ JB | Junction-to-board characterization parameter | 21.8 | °C/W |
| R θ JCbot | Junction-to-case (bottom) thermal resistance | n/a | °C/W |
BQ25101H Typical Application
The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at space-limited portable applications. The fast charge current can be programmed from 10 mA to 250 mA through an external resistor on ISET pin. The pre_charge and termination current can also be programmed through the resistor connected on PRETERM pin. The device has complete system-level protection such as input under-voltage lockout (UVLO), input over-voltage protection (OVP), sleep mode, thermal regulation, safety timers, and NTC monitoring input.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| BQ25100 | Texas Instruments | — |
| BQ25100A | Texas Instruments | — |
| BQ25100H | Texas Instruments | — |
| BQ25100L | Texas Instruments | — |
| BQ25101 | Texas Instruments | — |
| BQ25101/01H | Texas Instruments | — |
| BQ25101/101H | Texas Instruments | — |
| BQ25101/1H | Texas Instruments | — |
| BQ25101HYFPR | Texas Instruments | — |
| BQ25101HYFPR.A | Texas Instruments | — |
| BQ25101HYFPT | Texas Instruments | — |
| BQ25101HYFPT.A | Texas Instruments | — |
| BQ25101YFPR | Texas Instruments | — |
| BQ25101YFPR.A | Texas Instruments | — |
| BQ25101YFPT | Texas Instruments | 6-XFBGA, DSBGA |
| BQ25101YFPT.A | Texas Instruments | — |
More datasheets
Ask your AI agent about the BQ25101H
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the BQ25101H run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.