Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

BQ25100H

Single-Cell Li-Ion Linear Battery Charger

The BQ25100H is a single-cell li-ion linear battery charger from Texas Instruments. View the full BQ25100H datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

BQ25100H shares its datasheet with BQ25101, whose page lists every part number it covers.

Official BQ25100H datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Single-Cell Li-Ion Linear Battery Charger

BQ25100H Key Specifications

ParameterValue
Battery ChemistryLithium Ion/Polymer
Battery Pack Voltage4.2V
Charge Current (Max)250mA
Contact PlatingCopper, Silver, Tin
Current - ChargingConstant - Programmable
Fault ProtectionOver Temperature, Over Voltage, Short Circuit
Height500 µm
Lead FreeLead Free
Length1 mm
Lifecycle StatusProduction (Last Updated: 2 days ago)
Manufacturer Lifecycle StatusACTIVE (Last Updated: 2 days ago)
Max Operating Temperature125 °C
Min Operating Temperature0 °C
MountSurface Mount
Mounting TypeSurface Mount
Number of Cells1
Number of Cells1
Number of Pins6
Operating Supply Voltage28 V
Operating Temperature0°C ~ 125°C (TJ)
Output Current250 mA
Output Voltage4.2 V
Package / Case6-XFBGA, DSBGA
PackagingMouseReel
Programmable FeaturesCurrent
RoHSCompliant
Schedule B8542390000, 8542390000|8542390000|8542390000|8542390000|8542390000
Standard Pack Qty250
Supplier Device Package6-DSBGA
Thickness500 µm
Input Voltage (Max)6.45V
Width1.4 mm

BQ25100H Overview

Part: bq25101 (bq2510x family: bq25100, bq25101, bq25100A, bq25100H, bq25101H, bq25100L) — Texas Instruments

Type: Single-Cell Li-Ion/Li-Pol Linear Battery Charger

Description: 250-mA linear Li-Ion battery charger with 30-V input rating and 6.5-V input overvoltage protection, 1-mA minimum termination current, ±1% charge voltage accuracy and a maximum of 75 nA battery leakage, in a 1.60 mm × 0.90 mm DSBGA package.

Operating Conditions:

  • Supply voltage (IN): 3.5–28 V (operating range restricted by VDPM and VOVP: 4.45–6.45 V)
  • Junction temperature: 0 to 125 °C
  • Fast-charge current: 10–250 mA (RISET 0.54–13.5 kΩ)

Absolute Maximum Ratings:

  • IN voltage: -0.3 to 30 V
  • OUT, PRE-TERM, ISET, TS, CHG pin voltage: -0.3 to 7 V
  • IN input current: 300 mA
  • OUT continuous output current: 300 mA
  • CHG sink current: 15 mA
  • Junction temperature: -40 to 150 °C
  • Storage temperature: -65 to 150 °C

Key Specs:

  • Output regulation voltage (bq25100/101): 4.16 / 4.2 / 4.23 V (min/typ/max), TJ 0–125 °C, IOUT 0–250 mA, VIN = 5 V
  • Variants: 4.30 V (bq25100A), 4.35 V (bq25100H/101H), 4.06 V (bq25100L, product preview)
  • Hot regulation voltage (bq25100/101): 4.06 V typ (4.02–4.1 V)
  • Battery leakage into OUT (VIN = 0 V): 75 nA max at 0–125 °C; 50 nA max at 0–85 °C
  • Fast-charge current: IOUT = KISET/RISET, KISET = 135 AΩ typ
  • UVLO exit: 3.3 V typ (3.15–3.45 V); OVP threshold: 6.67 V typ (6.52–6.82 V)
  • Pre-charge to fast-charge threshold (VLOWV): 2.5 V typ (2.4–2.6 V); default pre-charge 20% and termination 10% of charge current
  • Dropout (VIN–VOUT): 220 mV typ, 400 mV max at IOUT = 0.2 A
  • Active supply current (ICC): 0.75 mA typ, 1 mA max (TTDM, VIN = 6 V); standby current 125 μA max
  • Thermal resistance RθJA: 132.9 °C/W (YFP, 6 pins)

Features:

  • ±1% charge voltage accuracy and ±10% charge current accuracy
  • Adjustable termination and pre-charge thresholds via a single PRE-TERM resistor (bq25100 variants); minimum 1-mA termination current
  • Input voltage dynamic power management (VIN-DPM)
  • 125 °C thermal regulation and 150 °C thermal shutdown
  • OUT short-circuit protection and ISET short detection
  • JEITA-compliant operation via battery NTC (half fast-charge current at cold, reduced voltage at hot)
  • Fixed 10-hour safety timer
  • Termination and Timer Disable Mode (TTDM) for absent battery pack
  • CHG status output (bq25101/101H)

Applications:

  • Fitness accessories
  • Smart watches
  • Bluetooth headsets
  • Low-power handheld devices

Package:

  • DSBGA (6 pins), 1.60 mm × 0.90 mm (YFP)

BQ25100H Applications

  • Fitness Accessories
  • Smart Watches
  • Bluetooth ® Headsets
  • Low-Power Handheld Devices

1

The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at spacelimited portable applications. The high input voltage range with input overvoltage protection supports lowcost unregulated adapters.

The bq2510x has a single power output that charges the battery. A system load can be placed in parallel with the battery as long as the average system load does not keep the battery from charging fully during the 10 hour safety timer.

The battery is charged in three phases: conditioning, constant current and constant voltage. In all charge phases, an internal control loop monitors the IC junction temperature and reduces the charge current if an internal temperature threshold is exceeded.

The charger power stage and charge current sense functions are fully integrated. The charger function has high accuracy current and voltage regulation loops and charge termination. The pre-charge current and termination current threshold are programmed via an external resistor on the bq2510x. The fast charge current value is also programmable via an external resistor.

BQ25100H Pin Configuration

bq25100/100A/100H/100L

SPACING

BQ25100H Electrical Characteristics

Over junction temperature range 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)

PARAMETERTEST CONDITIONSMINTYPMAXUNIT
INPUT
UVLOUndervoltage lock-out exitV IN : 0 V → 4 V3.153.33.45V
V HYS_UVLOHysteresis on V UVLO_RISE fallingV IN : 4 V → 0 V; V UVLO_FALL = V UVLO_RISE - V HYS-UVLO250mV
V IN-DTInput power good detection threshold is V OUT + V IN-DTInput power good if V IN > V OUT + V IN-DT ; V OUT = 3.6 V; V IN : 3.5 V → 4 V1560130mV
V HYS-INDTHysteresis on V IN-DT fallingV OUT = 3.6 V; V IN : 4 V → 3.5 V31mV
t DGL(PG_PWR)Deglitch time on exiting sleepTime measured from V IN : 0 V → 5 V 1- μ s rise- time to charge enables; V OUT = 3.6 V29ms
t DGL(PG_NO-PWR)Deglitch time on V HYS-INDT power down. Same as entering sleep.Time measured from V IN : 5 V → 3.2 V 1- μ s fall- time to charge disables; V OUT = 3.6 V29ms
V OVPInput over-voltage protection thresholdV IN : 5 V → 12 V6.526.676.82V
t DGL(OVP-SET)Input over-voltage blanking timeV IN : 5 V → 12 V113μ s
V HYS-OVPHysteresis on OVPV IN : 11 V → 5 V110mV
t DGL(OVP-REC)Deglitch time exiting OVPTime measured from V IN : 12 V → 5 V 1- μ s fall- time to charge enables450μ s
V IN-DPMLow input voltage protection. Restricts lout at V IN-DPMLimit input source current to 50 mA; V OUT = 3.5 V; R ISET = 1.35 k Ω4.254.314.37V
ISET SHORT CIRCUIT TESTISET SHORT CIRCUIT TEST
R ISET_SHORTHighest resistor value considered a fault (short).R ISET : 540 Ω→ 250 Ω , Iout latches off; Cycle power to reset420450Ω
t DGL_SHORTDeglitch time transition from ISET short to Iout disableClear fault by disconnecting IN or cycling (high / low) TS/BAT_EN1ms
I OUT_CLMaximum OUT current limit regulation (Clamp)V IN = 5 V; V OUT = 3.6 V; R ISET : 540 Ω→ 250 Ω ; I OUT latches off after t DGL-SHORT550600650mA
BATTERY SHORT PROTECTIONBATTERY SHORT PROTECTION
V OUT(SC)OUT pin short-circuit detection threshold/ precharge thresholdV OUT :3 V → 0.5 V; No deglitch0.750.80.85V
V OUT(SC-HYS)OUT pin Short hysteresisRecovery ≥ V OUT(SC) + V OUT(SC-HYS) ; Rising; No deglitch77mV
I OUT(SC)Source current to OUT pin during short-circuit detection91113mA
QUIESCENT CURRENTQUIESCENT CURRENT
IBattery current into OUT pinV IN = 0 V; 0°C to 125°C75nA
OUT(PDWN)V IN = 0 V; 0°C to 85°C50
I OUT(DONE)OUT pin current, charging terminatedV IN = 6 V; V OUT > V OUT(REG)6μ A
I IN(STDBY)Standby current into IN pinTS = GND; V IN ≤ 6 V125μ A
I CCActive supply current, IN pinTS = open, V IN = 6 V; TTDM - no load on OUT pin; V OUT > V OUT(REG) ; IC enabled0.751mA
BATTERY CHARGER FAST-CHARGEBATTERY CHARGER FAST-CHARGE
T J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100/101)4.164.24.23V
V OUT(REG)T J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100A)4.264.34.33
V OUT(REG)Output voltageT J = 0°C to 125°C; I OUT = 0 mA to 250 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100H/101H)4.314.354.38
T J = -5°C to 55°C; I OUT = 10mA to 75 mA; V IN = 5.0 V; V TS-45°C ≤ V TS ≤ V TS-0°C (bq25100A)4.2754.34.325
V O_HT(REG)Battery hot regulation voltageV IN = 5.0 V; I OUT =10 mA to 250 mA; V TS-60°C ≤ V TS ≤ V TS-45°C (bq25100/101)4.024.064.1V
I OUT(RANGE)Programmed output 'fast charge' current rangeV IN = 5.0 V; I OUT =10 mA to 250 mA; V TS-60°C ≤ V TS ≤ V TS-45°C (bq25100H/101H) V OUT(REG) > V OUT > V LOWV ; V IN = 5 V; R ISET = 0.54 k Ω to 13.5 k Ω4.16 104.24.24 250mA

SLUSBV8C -AUGUST 2014-REVISED NOVEMBER 2014

BQ25100H Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)

MINMAXUNIT
Input voltageIN (with respect to VSS)-0.330V
OUT (with respect to VSS)-0.37V
PRE-TERM, ISET, TS, CHG (with respect to VSS)-0.37V
Input currentIN300mA
Output current (continuous)OUT300mA
Output sink currentCHG15mA
T JJunction temperatureJunction temperature-40150°C
MINNOMUNIT
VIN voltage range3.528V
ININ operating voltage range, Restricted by V DPM and V OVP4.456.45V
I INInput current, IN pin250mA
I OUTCurrent, OUT pin250mA
T JJunction temperature0125°C
R PRE-TERMPrograms precharge and termination current thresholds0.630k Ω
R ISETFast-charge current programming resistor0.5413.5k Ω
R TS10k NTC thermistor range without entering BAT_EN or TTDM1.66258k Ω

BQ25100H Thermal Information

THERMAL METRIC (1)THERMAL METRIC (1)bq25100 YFP (6 PINS)UNIT
R θ JAJunction-to-ambient thermal resistance132.9°C/W
R θ JCtopJunction-to-case (top) thermal resistance1.3°C/W
R θ JBJunction-to-board thermal resistance21.8°C/W
ψ JTJunction-to-top characterization parameter5.6°C/W
ψ JBJunction-to-board characterization parameter21.8°C/W
R θ JCbotJunction-to-case (bottom) thermal resistancen/a°C/W

BQ25100H Typical Application

The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at space-limited portable applications. The fast charge current can be programmed from 10 mA to 250 mA through an external resistor on ISET pin. The pre_charge and termination current can also be programmed through the resistor connected on PRETERM pin. The device has complete system-level protection such as input under-voltage lockout (UVLO), input over-voltage protection (OVP), sleep mode, thermal regulation, safety timers, and NTC monitoring input.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
BQ25100Texas Instruments—
BQ25100ATexas Instruments—
BQ25100LTexas Instruments—
BQ25101Texas Instruments—
BQ25101/01HTexas Instruments—
BQ25101/101HTexas Instruments—
BQ25101/1HTexas Instruments—
BQ25101HTexas Instruments—
BQ25101HYFPRTexas Instruments—
BQ25101HYFPR.ATexas Instruments—
BQ25101HYFPTTexas Instruments—
BQ25101HYFPT.ATexas Instruments—
BQ25101YFPRTexas Instruments—
BQ25101YFPR.ATexas Instruments—
BQ25101YFPTTexas Instruments6-XFBGA, DSBGA
BQ25101YFPT.ATexas Instruments—

More datasheets

All Texas Instruments datasheets (2,571)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the BQ25100H

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the BQ25100H run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.