AD8366
Dual Digital Variable Gain AmplifierThe AD8366 is a dual digital variable gain amplifier from Analog Devices. View the full AD8366 datasheet below including key specifications, pinout.
Official AD8366 datasheet (PDF) — the source this page was extracted from.
Manufacturer
Analog DevicesCategory
Dual Digital Variable Gain Amplifier
Package
32-Lead Lead Frame Chip Scale Package [LFCSP] (CP-32-21), Evaluation Board
AD8366 Key Specifications
| Parameter | Value |
|---|---|
| Packaging | Reel |
| Standard Pack Qty | 1500 |
| Slew Rate | 1100 V/μs (max gain), 1500 V/μs (min gain) |
| Gain Range | 4.5 dB to 20.25 dB |
| 3 DB Bandwidth | 600 MHz |
| Gain Step Size | 0.25 dB |
| OIP3 At 10 MHz | 45 dBm (38 dBVrms) |
| Supply Current | 180 mA typical |
| Supply Voltage | 4.75 V to 5.25 V (5 V nominal) |
| Disable Current | 3.2 mA |
| HD2/HD3 At 10 MHz | Better than -90 dBc (2 V p-p output) |
| Linear Output Swing | 6 V p-p (1 dB compression) |
| Operating Frequency | DC to 150 MHz (2 V p-p) |
| Operating Temperature | -40°C to +85°C |
| Gain Control Interface | SPI serial or parallel |
| Noise Figure At 10 MHz | 11.4 dB (max gain), 18 dB (min gain) |
| Differential Input Impedance | 217 Ω |
| Differential Output Impedance | 28 Ω |
AD8366 Overview
Part: AD8366 — Analog Devices
Type: Dual Digital Variable Gain Amplifier (VGA)
Description: Matched pair of differential, digitally controlled VGAs with 4.5 dB to 20.25 dB gain range in 0.25 dB steps, 600 MHz 3 dB bandwidth, and single 5 V supply operation.
Operating Conditions:
- Supply voltage: 4.75–5.25 V
- Operating temperature: -40 to +85 °C
- Input common-mode voltage: 1.5 V minimum, defaults to VPOS/2
- Output common-mode voltage: 1.6–3 V (HD2/HD3 better than -90 dBc at 2 V p-p output), defaults to VPOS/2
Absolute Maximum Ratings:
- Max supply voltage (VPSIx, VPSOx): 5.5 V
- Internal power dissipation: 1.4 W
- Max junction temperature: 150 °C
- Storage temperature: -65 to +150 °C
- Lead temperature (soldering, 60 sec): 300 °C
Key Specs:
- Gain range: 4.5 to 20.25 dB, 0.25 dB step, step accuracy ±0.25 dB (VS = 5 V, TA = 25 °C, 200 Ω source and load)
- Bandwidth: 600 MHz (3 dB), 200 MHz (1 dB), all gain codes
- Noise figure at 10 MHz: 11.4 dB at maximum gain, 18 dB at minimum gain
- HD2/HD3 at 10 MHz, 2 V p-p output: -97/-97 dBc at maximum gain, -96/-90 dBc at minimum gain
- OIP3 at 10 MHz (2 V p-p composite): 38 dBVrms at maximum gain, 36 dBVrms at minimum gain
- Differential input impedance: 217 Ω; differential output impedance: 28 Ω
- Linear output swing: 6 V p-p (1 dB compression)
- Total supply current: 180 mA typical (ENBL = 5 V); disable current 3.2 mA
- SPI clock: up to 44.4 MHz
Features:
- Matched pair of differential, digitally controlled VGAs
- Differential input and output
- Adjustable output common-mode via VCMA/VCMB
- Optional dc output offset correction loop
- Serial (SPI) or parallel gain control
- Power-down feature
- Single 5 V supply operation
Applications:
- Baseband I/Q receivers
- Diversity receivers
- Wideband ADC drivers
Package:
- 32-lead exposed paddle LFCSP (θJA 45.4 °C/W with pad soldered to board)
AD8366 Features
Matched pair of differential, digitally controlled VGAs Gain range: 4.5 dB to 20.25 dB
0.25 dB gain step size Operating frequency DC to 150 MHz (2 V p-p) 3 dB bandwidth: 600 MHz Noise figure (NF) 11.4 dB at 10 MHz at maximum gain 18 dB at 10 MHz at minimum gain OIP3: 45 dBm at 10 MHz HD2/HD3 Better than -90 dBc for 2 V p-p output at 10 MHz at
maximum gain
Differential input and output Adjustable output common-mode Optional dc output offset correction Serial/parallel mode gain control Power-down feature Single 5 V supply operation
AD8366 Applications
Baseband I/Q receivers Diversity receivers
Wideband ADC drivers
AD8366 Pin Configuration
| Pin | Name | Type | Description |
|---|---|---|---|
| 1 | VPSIA | - | Input and Output Stage Positive Supply Voltage (4.75 V to 5.25 V). |
| 2 | IPPA | - | Differential Inputs. |
| 3 | IPMA | - | Differential Inputs. |
| 4 | ENBL | - | Chip Enable. Pull this pin high to enable. |
| 5 | ICOM | - | Input and Output Ground Pins. Connect these pins via the lowest possible impedance to ground. |
| 6 | IPMB | - | Differential Inputs. |
| 7 | IPPB | - | Differential Inputs. |
| 8 | VPSIB | - | Input and Output Stage Positive Supply Voltage (4.75 V to 5.25 V). |
| 9 | DECB | - | VPOS/2 Reference Decoupling Node. Connect a decoupling capacitor from these nodes to ground. |
| 10 | OFSB | - | Output Offset Correction Loop Compensation. Connect a capacitor from these nodes to ground to enable the correction loop. Tie this pin to ground to disable. |
| 11 | CCMB | - | Connect These Nodes to Ground. |
| 12 | VCMB | - | Output Common-Mode Setpoint. These pins default to VPOS/2 if left open. Drive these pins from a low impedance source to change the output common-mode voltage. |
| 13 | VPSOB | - | Input and Output Stage Positive Supply Voltage (4.75 V to 5.25 V). |
| 14 | OPPB | - | Differential Outputs. |
| 15 | OPMB | - | Differential Outputs. |
| 16 | DENB | - | Data Enable. Pull these pins high to address each or both channels for parallel gain programming. These pins are not used in serial mode. |
| 17 | DENA | - | Data Enable. Pull these pins high to address each or both channels for parallel gain programming. These pins are not used in serial mode. |
| 18 | BIT5 | - | Parallel Data Path (When SENB Is Low). BIT3 to BIT5 are not used in serial mode. |
| 19 | BIT4 | - | Parallel Data Path (When SENB Is Low). BIT3 to BIT5 are not used in serial mode. |
| 20 | OCOM | - | Input and Output Ground Pins. Connect these pins via the lowest possible impedance to ground. |
| 21 | BIT3 | - | Parallel Data Path (When SENB Is Low). BIT3 to BIT5 are not used in serial mode. |
| 22 | BIT2/SCLK | - | Parallel Data Path (When SENB Is Low). When SENB is high, BIT2 becomes a serial clock (SCLK). |
| 23 | BIT1/SDAT | - | Parallel Data Path (When SENB Is Low). When SENB is high, BIT1 becomes a serial data input (SDAT). |
| 24 | BIT0/CS | - | Parallel Data Path (When SENB Is Low). When SENB is high, BIT0 becomes a chip select (CS). |
| 25 | SENB | - | Serial Interface Enable. Pull this pin high for serial gain programming mode and pull this pin low for parallel gain programming mode. |
| 26 | OPMA | - | Differential Outputs. |
| 27 | OPPA | - | Differential Outputs. |
| 28 | VPSOA | - | Input and Output Stage Positive Supply Voltage (4.75 V to 5.25 V). |
| 29 | VCMA | - | Output Common-Mode Setpoint. These pins default to VPOS/2 if left open. Drive these pins from a low impedance source to change the output common-mode voltage. |
| 30 | CCMA | - | Connect These Nodes to Ground. |
| 31 | OFSA | - | Output Offset Correction Loop Compensation. Connect a capacitor from these nodes to ground to enable the correction loop. Tie this pin to ground to disable. |
| 32 | DECA | - | VPOS/2 Reference Decoupling Node. Connect a decoupling capacitor from these nodes to ground. |
| EPAD | EPAD | - | The exposed pad must be connected to ground. |
AD8366 Ordering Information
| Model | Temperature Range | Package Description | Package Option | Packing |
|---|---|---|---|---|
| AD8366ACPZ-R7 | -40°C to +85°C | 32-Lead Lead Frame Chip Scale Package [LFCSP] | CP-32-21 | null |
| AD8366-EVALZ | null | Evaluation Board | null | null |
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| AD8366ACPZ-R7 | Analog Devices |
More datasheets
Ask your AI agent about the AD8366
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the AD8366 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.