Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

AD8138

Differential Amplifier / ADC Driver

The AD8138 is a differential amplifier / adc driver from Analog Devices. View the full AD8138 datasheet below including key specifications, pinout, absolute maximum ratings.

Official AD8138 datasheet (PDF) — the source this page was extracted from.

Manufacturer

Analog Devices

Category

Differential Amplifier / ADC Driver

Package

8-Lead SOIC (R-8), 8-Lead MSOP (RM-8)

AD8138 Key Specifications

ParameterValue
PackagingTube
Standard Pack Qty50
CMRR-77 dB typical
Slew Rate1150 V/μs
IP3 (20 MHz)37 dBm
Offset Voltage±1 mV typical (±2.5 mV max)
Supply Voltage+3 V to ±5 V
Package Options8-Lead SOIC, 8-Lead MSOP
Power Consumption90 mW on 5 V
Input Bias Current3.5 μA typical (7 μA max)
Input Current Noise2 pA/√Hz
Input Voltage Noise5 nV/√Hz
Settling Time (0.01%)16 ns
-3 DB Bandwidth (G=+1)320 MHz
Gain Flatness (0.1 DB)40 MHz
Overdrive Recovery Time4 ns
Operating Temperature Range-40°C to +85°C
Third Harmonic (5 MHz, 2V P-P)-114 dBc
Second Harmonic (5 MHz, 2V P-P)-94 dBc

AD8138 Overview

Part: AD8138 — Analog Devices

Type: Differential Amplifier / ADC Driver

Description: Low distortion differential ADC driver with 320 MHz -3 dB bandwidth (G = +1), 1150 V/μs slew rate, and -94 dBc second harmonic at 5 MHz, operating from +3 V to ±5 V supplies.

Operating Conditions:

  • Supply voltage: ±1.4 V to ±5.5 V (dual supply); 2.7 V to 11 V (single supply, VS = 5 V specifications)
  • Operating temperature: -40 to +85 °C
  • Output common-mode voltage set by the VOCM pin (1:1 ratio)

Absolute Maximum Ratings:

  • Max supply voltage: ±5.5 V
  • VOCM: ±VS
  • Internal power dissipation: 550 mW
  • Max junction temperature: 150 °C
  • Storage temperature: -65 to +150 °C
  • Lead temperature (soldering, 10 sec): 300 °C

Key Specs:

  • -3 dB small-signal bandwidth: 320 MHz typ (VS = ±5 V, VOUT = 0.5 V p-p, CF = 0 pF); 310 MHz typ at VS = 5 V
  • Slew rate: 1150 V/μs (VS = ±5 V, 2 V p-p); 950 V/μs (VS = 5 V)
  • Settling time to 0.01%: 16 ns (2 V p-p, CF = 1 pF)
  • Second harmonic: -94 dBc at 5 MHz, -87 dBc at 20 MHz (VS = ±5 V, 2 V p-p, RL,dm = 800 Ω)
  • Voltage noise (RTI): 5 nV/√Hz (100 kHz to 40 MHz)
  • Offset voltage: ±1 mV typ, ±2.5 mV max (differential)
  • Quiescent current: 20 mA typ (18 to 23 mA, VS = ±5 V)
  • Output current: 95 mA typ; CMRR -77 dB typ (-70 dB max); PSRR -90 dB typ (-70 dB max)

Features:

  • Easy-to-use single-ended-to-differential conversion
  • Adjustable output common-mode voltage
  • Externally adjustable gain
  • Low harmonic distortion
  • Fast overdrive recovery of 4 ns
  • 0.1 dB gain flatness to 30 MHz (VS = ±5 V, 0.5 V p-p, CF = 0 pF)
  • Internal feedback for balanced output gain and phase matching
  • Available in 8-lead SOIC and MSOP packages

Applications:

  • ADC drivers
  • Single-ended-to-differential converters
  • IF and baseband gain blocks
  • Differential buffers
  • Line drivers

Package:

  • 8-Lead SOIC (θJA 121 °C/W, 4-layer)
  • 8-Lead MSOP (θJA 145 °C/W, 4-layer)

AD8138 Features

Easy to use, single-ended-to-differential conversion Adjustable output common-mode voltage Externally adjustable gain Low harmonic distortion -94 dBc SFDR at 5 MHz -85 dBc SFDR at 20 MHz -3 dB bandwidth of 320 MHz, G = +1 Fast settling to 0.01% of 16 ns Slew rate 1150 V/μs Fast overdrive recovery of 4 ns Low input voltage noise of 5 nV/√Hz 1 mV typical offset voltage Wide supply range +3 V to ±5 V Low power 90 mW on 5 V 0.1 dB gain flatness to 40 MHz Available in 8-Lead SOIC and MSOP packages

AD8138 Applications

ADC drivers Single-ended-to-differential converters IF and baseband gain blocks Differential buffers

Line drivers

AD8138 Pin Configuration

PinNameTypeDescription
1-IN-Negative Input Summing Node.
2VOCM-Voltage applied to this pin sets the common-mode output voltage with a ratio of 1:1. For example, 1 V dc on VOCM sets the dc bias level on +OUT and -OUT to 1 V.
3V+-Positive Supply Voltage.
4+OUT-Positive Output. Note that the voltage at -DIN is inverted at +OUT (see Figure 42).
5-OUT-Negative Output. Note that the voltage at +DIN is inverted at -OUT (see Figure 42).
6V--Negative Supply Voltage.
7NC-No Connect.
8+IN-Positive Input Summing Node.

AD8138 Absolute Maximum Ratings

Table 5. - ParameterRatings
Supply Voltage±5.5V
V OCM±V S
Internal Power Dissipation550mW
Operating Temperature Range-40°C to +85°C
Storage Temperature Range-65°C to +150°C
Lead Temperature (Soldering 10 sec)300°C
Junction Temperature150°C

Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability.

AD8138 Thermal Information

θJA is specified for the worst-case conditions, that is, θJA is specified for the device soldered in a circuit board in still air.

Table 6. PackageTypeθ JAUnit
8-Lead SOIC/4-Layer121°C/W
8-Lead MSOP/4-Layer145°C/W

AD8138 Typical Application

The AD8138 eliminates the need for a transformer with high performance ADCs, preserving the low frequency and dc information. The common-mode level of the differential output is OCM pin, easily level-shifting the input signals for driving single-supply ADCs. Fast overload recovery preserves sampling accuracy.

The AD8138 distortion performance makes it an ideal ADC driver for communication systems, with distortion performance good enough to drive state-of-the-art 10-bit to 16-bit converters at high frequencies. The high bandwidth and IP3 of the AD8138 also make it appropriate for use as a gain block in IF and baseband signal chains. The AD8138 offset and dynamic performance makes it well suited for a wide variety of signal processing and data acquisition applications.

The AD8138 is available in both SOIC and MSOP packages for operation over -40°C to +85°C temperatures.

AD8138 Ordering Information

MPNPackageTemperature RangePackingPackage OptionBranding
AD8138AR8-Lead SOIC-40°C to +85°CnullR-8null
AD8138AR-REEL8-Lead SOIC, 13" Tape and Reel-40°C to +85°C13" Tape and ReelR-8null
AD8138AR-REEL78-Lead SOIC, 7" Tape and Reel-40°C to +85°C7" Tape and ReelR-8null
AD8138ARZ8-Lead SOIC-40°C to +85°CnullR-8null
AD8138ARZ-RL8-Lead SOIC, 13" Tape and Reel-40°C to +85°C13" Tape and ReelR-8null
AD8138ARZ-R78-Lead SOIC, 7" Tape and Reel-40°C to +85°C7" Tape and ReelR-8null
AD8138ARM8-Lead MSOP-40°C to +85°CnullRM-8HBA
AD8138ARM-REEL8-Lead MSOP, 13" Tape and Reel-40°C to +85°C13" Tape and ReelRM-8HBA
AD8138ARM-REEL78-Lead MSOP, 7" Tape and Reel-40°C to +85°C7" Tape and ReelRM-8HBA
AD8138ARMZ8-Lead MSOP-40°C to +85°CnullRM-8HBA#
AD8138ARMZ-REEL8-Lead MSOP, 13" Tape and Reel-40°C to +85°C13" Tape and ReelRM-8HBA#
AD8138ARMZ-REEL78-Lead MSOP, 7" Tape and Reel-40°C to +85°C7" Tape and ReelRM-8HBA#

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
AD8138ARAnalog Devices8-Lead SOIC (R-8)
AD8138AR-REELAnalog Devices8-Lead SOIC (R-8)
AD8138AR-REEL7Analog Devices8-Lead SOIC (R-8)
AD8138ARMAnalog Devices8-Lead MSOP (RM-8)
AD8138ARM-REELAnalog Devices8-Lead MSOP (RM-8)
AD8138ARM-REEL7Analog Devices8-Lead MSOP (RM-8)
AD8138ARMZAnalog Devices8-Lead MSOP (RM-8)
AD8138ARMZ-REELAnalog Devices8-Lead MSOP (RM-8)
AD8138ARMZ-REEL7Analog Devices8-Lead MSOP (RM-8)
AD8138ARZAnalog Devices8-Lead SOIC (R-8)
AD8138ARZ-R7Analog Devices8-Lead SOIC (R-8)
AD8138ARZ-RLAnalog Devices8-Lead SOIC (R-8)

More datasheets

All Analog Devices datasheets (757)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the AD8138

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the AD8138 run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.