SX1262IMLTRT

Part: SX1262IMLTRT — Semtech

Type: Sub-GHz LoRa/(G)FSK RF Transceiver

Description: Sub-GHz RF transceiver covering 150–960 MHz with up to +22 dBm transmit power, LoRa, Long Range FHSS and (G)FSK modulation, and 4.2 mA active receive current.

Operating Conditions:

• Frequency coverage: 150 MHz to 960 MHz

Absolute Maximum Ratings:

• Max supply voltage (VBAT and VBAT_IO): 3.9 V (min -0.5 V)
• Max junction/storage temperature: 125 °C (min -55 °C)
• Max RF input level: 10 dBm

Key Specs:

• Active receive current: 4.2 mA
• Maximum transmit power: +22 dBm (SX1262)
• Frequency range: 150–960 MHz
• Modulations: LoRa, LR-FHSS, (G)FSK
• Host interface: SPI with BUSY line and multi-purpose DIOs
• Power regulation: DC-DC or LDO selectable

Features:

• Highly efficient integrated power amplifier
• LoRa and Long Range FHSS modulations for LPWAN, and (G)FSK for legacy use
• Designed to comply with the LoRaWAN physical layer specification
• Suitable for systems targeting ETSI EN 300 220, FCC CFR 47 Part 15, China regulatory requirements and ARIB T-108
• Flexible DIO supply
• Integrated data buffer, packet engines and TCXO control

Applications:

• Smart meters
• Supply chain and logistics
• Building automation
• Agricultural sensors
• Smart cities
• Retail store sensors
• Asset tracking
• Street lights
• Parking sensors
• Environmental sensors
• Healthcare
• Safety and security sensors
• Remote control applications

Package:

• QFN-24, Pb-free, halogen free, RoHS/WEEE compliant (tape and reel, MOQ 3,000 pieces)

The level of integration and the low consumption within SX1261/2 enable a new generation of Internet of Things applications.

• Smart meters
• Supply chain and logistics
• Building automation
• Agricultural sensors
• Smart cities
• Retail store sensors
• Asset tracking
• Street lights
• Parking sensors
• Environmental sensors
• Healthcare
• Safety and security sensors
• Remote control applications

The electrical specifications are given with the following conditions unless otherwise specified:

• VBAT_IO = VBAT = 3.3 V, all current consumptions are given for VBAT connected to VBAT_IO
• Temperature = 25 °C
• FXOSC = 32 MHz, with specified crystal
• FRF = 434/490/868/915 MHz
• All RF impedances matched
• Transmit mode output power defined into a 50 load impedance
• FSK BER = 0.1%, 2-level FSK modulation without pre-filtering, BR = 4.8 kb/s, FDA = ± 5 kHz, BW_F = 20 kHz double-sided
• LoRa® PER = 1%, packet 64 bytes, preamble 8 symbols, CR = 4/5, CRC on payload enabled, explicit header mode
• RX/TX specifications given using default RX gain step and direct tie connection between Rx and Tx
• Blocking immunity, ACR and co-channel rejection are given for a single tone (CW) interferer and referenced to sensitivity +3 dB
• Optional TCXO and RF Switch power consumption always excluded

Throughout this document, all receiver bandwidths are expressed as 'double-sideband'. This is valid for LoRa® and FSK modulations.

Stresses above the values listed below may cause permanent device failure. Exposure to absolute maximum ratings for extended periods may affect device reliability, reducing product life time.

Table 3-2: Absolute Maximum Ratings

The transceiver is delivered in a 4x4mm QFN package with 0.5 mm pitch:

Figure 16-1: QFN 4x4 Package Outline Drawing

Figure 16-1: QFN 4x4 Package Outline Drawing