MICRF211AYQS
OOK/ASK RF ReceiverThe MICRF211AYQS is a ook/ask rf receiver from Microchip. View the full MICRF211AYQS datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
MICRF211AYQS shares its datasheet with MICRF211, whose page lists every part number it covers.
Official MICRF211AYQS datasheet (PDF) — the source this page was extracted from.
Manufacturer
Microchip
Category
OOK/ASK RF Receiver
Package
16-SSOP (0.154", 3.90mm Width)
Lifecycle
Production (Last Updated: 1 day ago)
MICRF211AYQS Key Specifications
| Parameter | Value |
|---|---|
| Antenna Connector | PCB, Surface Mount |
| Applications | ISM, Garage Door Openers, RKE |
| Bandwidth | 330 kHz |
| Case/Package | QSOP |
| Country of Assembly | Malaysia |
| Country of Fabrication | Austria |
| Country of Origin | Malaysia |
| Current - Receiving | 6 mA |
| Current - Receiving | 6mA |
| Data Interface | PCB, Surface Mount |
| Data Rate (Max) | 10kbps |
| Depth | 3.91 mm |
| Export Control Classification Number (ECCN) Code | EAR99 |
| Features | No IF Filter Required |
| Frequency | 380MHz ~ 450MHz |
| Frequency | 450 MHz |
| Harmonized Tariff Schedule (HTS) Code | 8542.39.0060 |
| Height | 1.47 mm |
| HS Code | 8542.39.0090 |
| Lead Free | Lead Free |
| Length | 4.9 mm |
| Lifecycle Status | Production (Last Updated: 1 day ago) |
| Manufacturer Lifecycle Status | REL (Last Updated: 1 day ago) |
| Max Frequency | 450 MHz |
| Max Operating Temperature | 105 °C |
| Max Supply Voltage | 3.6 V |
| Min Operating Temperature | -40 °C |
| Min Supply Voltage | 3 V |
| Modulation or Protocol | ASK, OOK |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Nominal Supply Current | 6 mA |
| Number of Pins | 16 |
| Operating Temperature | -40°C ~ 105°C |
| Package / Case | 16-SSOP (0.154", 3.90mm Width) |
| Packaging | Tube |
| Projected EOL Date | 2034-02-02 |
| Radiation Hardening | No |
| REACH SVHC | Unaffected |
| RoHS | Compliant |
| Schedule B | 8542390000 |
| Sensitivity | -110dBm |
| Sensitivity (dBm) | -110 dBm |
| Standard Pack Qty | 98 |
| Supplier Device Package | 16-QSOP |
| Supply Voltage | 3V ~ 3.6V |
| Width | 3.91 mm |
MICRF211AYQS Overview
Part: MICRF211AYQS — Micrel Inc.
Type: OOK/ASK Super-heterodyne RF Receiver (QwikRadio)
Description: 3 V, 433.92 MHz OOK/ASK receiver with -110 dBm typical sensitivity at 1 kbps, image-rejection mixer, and 6.0 mA typical continuous-operation supply current.
Operating Conditions:
- Supply voltage: 3.0–3.6 V
- Operating temperature: -40 to +105 °C
- Frequency range: 380–450 MHz (433.92 MHz characterized); data rates up to 10 kbps (Manchester encoded)
- Maximum input RF power: -20 dBm (operating rating)
Absolute Maximum Ratings:
- Max supply voltage (VDD): 5 V
- Max input voltage: 5 V
- Max junction temperature: 150 °C
- Storage temperature: -65 to +150 °C
- Max receiver input power: +10 dBm
- Lead temperature (soldering, 10 s): 260 °C
- ESD: 2 kV CDM, 200 V HBM, 100 V MM
Key Specs:
- Operating supply current: 6.0 mA typ (continuous operation, fRX = 433.92 MHz)
- Shutdown current: 0.5 μA typ
- Receiver sensitivity: -110 dBm typ (1 kbps, BER 10^-2, matched to 50 Ω, fRX = 433.92 MHz)
- Image rejection: 20 dB typ
- 1st IF center frequency: 1.2 MHz; IF bandwidth: 330 MHz-scaled value of 330 kHz typ at 433.92 MHz
- Demodulator filter bandwidth: 1625–13000 Hz, selectable via SEL0/SEL1
- RSSI: 0.4 to 2 V output range, 25 mV/dB slope (-110 to -40 dBm), 200 Ω output impedance
- Reference oscillator: 13.52127 MHz typ for 433.92 MHz (10 pF crystal load)
- Receive modulation duty cycle: 20–80 %
Features:
- -110 dBm sensitivity at 1 kbps, BER 10^-2
- Image rejection mixer
- Frequency range 380–450 MHz
- Analog RSSI output
- No IF filter required
- Excellent selectivity and noise rejection
- Low external part count (crystal, CTH, CAGC capacitors minimum)
- Four selectable demodulator filter bandwidths
Applications:
Package:
- 16-Pin QSOP
MICRF211AYQS Features
- -110dBm sensitivity, 1kbps and BER 10 -2
- Image rejection mixer
- Frequency from 380MHz to 450MHz
- Low power, 6.0mA @ 433.92MHz, continuous on data rates to 10kbps (Manchester Encoded)
- Analog RSSI output
- No IF filter required
- Excellent selectivity and noise rejection
- Low external part count
MICRF211AYQS Pin Configuration
| 16-Pin QSOP | Pin Name | Pin Function |
|---|---|---|
| 1 | RO1 | Reference resonator input connection to Colpitts oscillator stage. May also be driven by external reference signal of 1.5V p-p amplitude maximum. |
| 2 | GNDRF | Negative supply connection associated with ANT RF input. |
| 3 | ANT | RF signal input from antenna. Internally AC coupled. It is recommended that a matching network with an inductor -to-RF ground is used to improve ESD protection. |
| 4 | GNDRF | Negative supply connection associated with ANT RF input. |
| 5 | VDD | Positive supply connection for all chip functions. |
| 6 | SQ | Squelch control logic input with an active internal pull-up when not shut down. |
| 7 | SEL0 | Logic control input with active internal pull-up. Used in conjunction with SEL1 to control the demodulator low pass filter bandwidth. (See filter table for SEL0 and SEL1 in application section) |
| 8 | SHDN | Shutdown logic control input. Active internal pull-up. |
| 9 | GND | Negative supply connection for all chip functions except RF input. |
| 10 | DO | Demodulated data output. |
| 11 | SEL1 | Logic control input with active internal pull-up. Used in conjunction with SEL0 to control the demodulator low pass filter bandwidth. (See filter table for SEL0 and SEL1 in application section) |
| 12 | CTH | Demodulation threshold voltage integration capacitor connection. Tie an external capacitor across CTH pin and GND to set the settling time for the demodulation data slicing level. Values above 1nF are recommended and should be optimized for data rate and data profile. |
| 13 | CAGC | AGC filter capacitor connection. CAGC capacitor, normally greater than 0.47μF, is connected from this pin to GND |
| 14 | RSSI | Received signal strength indication output. Output is from a buffer with 200Ω typical output impedance. |
| 15 | NC | Not Connected (Connect to Ground) |
| 16 | RO2 | Reference resonator input connection to Colpitts oscillator stage, 7pF, in parallel with low resistance MOS switch-to-GND, during normal operation. Driven by startup excitation circuit during the internal startup control sequence. |
MICRF211AYQS
MICRF211AYQS Electrical Characteristics
Specifications apply for 3.0V < VDD < 3.6V, VSS = 0V, CAGC = 4.7μF, CTH = 0.1μF, fRX = 433.92MHz, unless otherwise noted. Bold values indicate -40°C - TA - 105°C. 1kbps data rate (Manchester encoded), reference oscillator frequency = 13.52127MHz.
| Parameter | Condition | Min | Typ | Max | Units |
|---|---|---|---|---|---|
| Operating Supply Current | Continuous Operation, f RX = 433.92MHz | 6.0 | mA | ||
| Shut down Current | 0.5 | μA | |||
| Image Rejection | 20 | dB | |||
| 1 st IF Center Frequency | f RX = 433.92MHz | 1.2 | MHz | ||
| Receiver Sensitivity@ 1kbps | f RX = 433.92MHz (matched to 50Ω) BER=10 -2 | -110 | dBm | ||
| IF Bandwidth | f RX = 433.92MHz | 330 | kHz | ||
| Antenna Input Impedance | f RX = 433.92MHz | 19 - j174 | Ω | ||
| Receive Modulation Duty Cycle | Note 5 | 20 | 80 | % | |
| AGC Attack / Decay Ratio | t ATTACK / t DECAY | 0.1 | |||
| AGC pin leakage current | T A = 25°C T A = +105°C | ± 2 ± 800 | nA nA | ||
| AGC Dynamic Range | RF IN @-40dBm | 1.15 | V | ||
| AGC Dynamic Range | RF IN @-100dBm | 1.70 | V | ||
| Reference Oscillator Frequency | f RX = 433.92MHz Crystal Load Cap = 10pF | 13.52127 | MHz | ||
| Reference Oscillator Input Impedance | 300 | kΩ | |||
| Reference Oscillator Input Range | 0.2 | 1.5 | Vp-p | ||
| Reference Oscillator Source Current | V(REFOSC) = 0V | 3.5 | μA |
MICRF211AYQS Absolute Maximum Ratings
| Parameter | Limit |
|---|---|
| Supply Voltage (V DD ) | +5V |
| Input Voltage | +5V |
| Junction Temperature | +150°C |
| Lead Temperature (soldering, 10sec.) | 260°C |
| Storage Temperature (T S ) | -65°C to +150°C |
| Maximum Receiver Input Power | +10dBm |
| ESD Rating (3) | 2kV CDM |
| . | 200V HBM |
................................. 100V Machine Model
MICRF211AYQS Typical Application
433.92 MHz, 1kHz Baud Rate Example
QwikRadio is a registered trademark of Micrel, Inc.
Certain of the QwikRadio ICs were developed under a development agreement with AIT of Orlando, FL.
Micrel Inc. · 2180 Fortune Drive · San Jose, CA 95131 · USA · tel +1 (408) 944-0800 · fax + 1 (408) 474-1000 · http://www.micrel.com
MICRF211AYQS Package Information
Table 10. QR211HE1 Bill of Materials, 433.92 MHz.
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| MICRF211 | Microchip Technology | QSOP-16 |
Ask your AI agent about the MICRF211AYQS
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the MICRF211AYQS run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.