MAX20050/51

The MAX20050-MAX20053 are high-brightness LED (HB LED) drivers for automotive exterior lighting applications. Consisting of a fully synchronous step-down converter with integrated MOSFETs, the devices are capable of driving a series string of LEDs at up to 2A, with a minimum number of external components. The MAX20050/ MAX20052 utilize internal loop compensation to minimize component count, while the MAX20051/MAX20053 use external compensation for full flexibility.

The wide 4.5V to 65V input supply range supports extreme automotive cold crank and load-dump conditions. A lowand high-switching frequency option (400kHz or 2.1MHz) provides the designer with the flexibility to optimize for solution size or efficiency, while avoiding interference within the AM band. Spread spectrum provides further options for the designer to reduce EMI at the system level. The MAX20050/MAX20051 have an internal switching frequency of 400kHz, while the MAX20052/MAX20053 have an internal switching frequency of 2.1MHz.

High-side current regulation means only a single connection to the LED string is required; grounding of the string can be done locally. In addition to PWM dimming, the ICs provide analog dimming using the REFI pin. Fullscale current regulation accuracy is ±2.5%, while the accuracy is ±8% at 10% of full-scale over the full temperature range of -40°C to +125°C. A 5V, 10mA LDO output is available for biasing other circuits.

Fault-protection mechanisms include output overload, short-circuit, and device overtemperature protection. The devices are specified for operation over the full -40°C to +125°C temperature range and are available in thermally enhanced 12-pin (3mm x 3mm) TDFN and 14-pin (5mm x 4.4mm) TSSOP packages with an exposed pad.

• Fully Synchronous 2A Step-Down Converter with Integrated 0.14Ω (typ) MOSFETs
• Wide 4.5V to 65V Input Supply Range
• Two Switching Frequency Options: 400kHz and 2.1MHz
• Internal Loop Compensation (MAX20050/MAX20052) and External Loop Compensation (MAX20051/MAX20053) Options
• Switching Frequency Synchronized to PWM Dimming Signal
• Active-Low Fault (FLT) Indicator
• Output Short-Circuit Protection
• High-Side Current Regulation Eliminates One Connection to LED String
• Spread-Spectrum Mode Alleviates EMI Problems
• Low 200mV Full-Scale High-Side Current-Sense Voltage
• REFI Pin Adjusts LED Current Down to Zero
• PWM Dimming Disconnects Both High- and LowSide MOSFET Drivers
• 5V, 10mA LDO Output Provides Bias to Other Circuits
• Ultra-Low Shutdown Current (5μA typ)
• Output Overload, Short-Circuit, and Overtemperature Protections
• 12-Pin (3mm x 3mm) TDFN and 14-Pin (5mm x 4.4mm) TSSOP Package Options

Ordering Information appears at end of data sheet.

• Daytime Running Lamps (DRLs)
• Fog Lamps
• Clearance Lamps (CLLs)
• Corner Lamps (CLs)
• Rear Lamps
• Head Lamps
• Commercial, Industrial, and Architectural Lighting

(V IN = 12V, V REFI = 1.2V, V PWM = V CC , T A = T J = -40°C to +125°C, unless otherwise noted. Typical values are at T A = +25°C.) (Note 2)

│

• Continuous Power Dissipation (T A = +70°C) (Note 1) 12-Pin TDFN-EP (derate 24.4 mW/°C above +70°C)
• 14-Pin TSSOP-EP (derate 25.6 mW/°C above +70°C) ........................................................2051.3mW
• Operating Temperature Range..........................-40°C to Junction Temperature......................................................+150°C
• Storage Temperature Range.............................-65°C to
• Lead Temperature (soldering, 10s) .................................+300°C
• Soldering Temperature (reflow).......................................+260°C
• Parameter

• TSSOP
• Junction-to-Ambient Thermal Resistance (θ JA )
• Junction-to-Case Thermal Resistance (θ JC )

Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial .

For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages . Note that a '+', '#', or '-' in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status.