LDK220
Low-Dropout Linear RegulatorThe LDK220 is a low-dropout linear regulator from STMicroelectronics. View the full LDK220 datasheet below including key specifications, electrical characteristics, absolute maximum ratings.
Official LDK220 datasheet (PDF) — the source this page was extracted from.
Manufacturer
STMicroelectronicsCategory
Low-Dropout Linear Regulator
LDK220 Key Specifications
| Parameter | Value |
|---|---|
| Accuracy | 2 % |
| Case/Package | LSSOP |
| China RoHS | Compliant |
| Control Features | Enable |
| Output Current | 200mA |
| Quiescent Current | 90 µA |
| Supply Current (Max) | 100 µA |
| Dropout Voltage | 350 mV |
| Height | 1.3 mm |
| Height - Seated (Max) | 1.45 mm |
| Introduction Date | 2014-03-19 |
| Length | 2.95 mm |
| Lifecycle Status | Production (Last Updated: 10 months ago) |
| Max Input Voltage | 13.2 V |
| Max Junction Temperature (Tj) | 125 °C |
| Max Operating Temperature | 125 °C |
| Max Output Current | 200 mA |
| Max Output Voltage | 1.22 V |
| Max Power Dissipation | 500 mW |
| Min Input Voltage | 2.5 V |
| Min Operating Temperature | -40 °C |
| Min Output Voltage | 1.149 V |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Number of Outputs | 1 |
| Number of Pins | 5 |
| Number of Regulators | 1 |
| Number of Regulators | 1 |
| Number of Terminals | 5 |
| Operating Temperature | -40°C ~ 125°C |
| Output Configuration | Positive |
| Output Current | 200 mA |
| Output Type | Adjustable |
| Output Type | Adjustable |
| Output Voltage | 12 V |
| Package / Case | SC-74A, SOT-753 |
| Packaging | Cut Tape |
| Packaging | MouseReel |
| Polarity | Positive |
| Power Rating | 500 mW |
| Protection Features | Over Current, Over Temperature |
| PSRR | 60dB ~ 45dB (120Hz ~ 10kHz) |
| Quiescent Current | 60 µA |
| Radiation Hardening | No |
| REACH SVHC | Unaffected |
| Reference Voltage | 1.19 V |
| RoHS | Compliant |
| Schedule B | 8542390000, 8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|8542390000|85 |
| Standard Pack Qty | 3000 |
| Supplier Device Package | SOT-23-5 |
| Terminal Pitch | 950 µm |
| Input Voltage (Max) | 13.2V |
| Dropout Voltage | 0.35V @ 200mA |
| Weight | 29.993795 mg |
| Width | 1.6 mm |
LDK220 Overview
Part: LDK220M-R — STMicroelectronics
Type: Low-Dropout (LDO) Linear Regulator, adjustable output (SOT23-5L)
Description: 2.5–13.2 V input, 200 mA low-noise LDO with 55 μA typical quiescent current, 100 mV typical dropout at 100 mA, and adjustable output (1.185 V reference).
Operating Conditions:
- Input voltage: 2.5–13.2 V
- Operating junction temperature: -40 to 125 °C
- Output current: up to 200 mA guaranteed
- Output capacitor: 1–22 μF ceramic
Absolute Maximum Ratings:
- Max input voltage (VIN): 14 V
- Output current: internally limited
- Power dissipation: 500 mW
- Storage temperature: -65 to 150 °C
- Operating junction temperature: -40 to 125 °C
Key Specs:
- Adjustable reference voltage: 1.185 V typ. (TJ = 25 °C); accuracy ±2% at 25 °C, ±3% over -40 to 125 °C
- Dropout voltage: 100 mV typ. at 100 mA; 200 mV typ., 350 mV max at 200 mA (VOUT = 3.3 V)
- Quiescent current: 55 μA typ., 90 μA max at IOUT = 0 mA; 60 μA typ., 100 μA max at IOUT = 200 mA
- Off-mode input current: 0.1 μA typ., 1 μA max (VEN = GND, TJ = 25 °C)
- Line regulation: 0.001 %/V typ., 0.05 %/V max
- Load regulation: 0.0002 %/mA typ., 0.003 %/mA max (1–200 mA)
- Output noise: 100 μVRMS/V typ. (10 Hz–100 kHz, IOUT = 10 mA)
- PSRR: 60 dB typ. (120 Hz–1 kHz); 45 dB typ. (10 kHz)
- Short-circuit current: 400 mA typ.
- Enable thresholds: logic high 1.2 V min, logic low 0.4 V max
- Thermal shutdown: 160 °C, 20 °C hysteresis
- Thermal resistance RthJA (SOT23-5L): 160 °C/W
Features:
- Very low dropout voltage
- Low quiescent current and low noise
- Logic-controlled electronic shutdown
- Output discharge function (18 Ω typ. in the fixed version)
- Stable with 1 μF ceramic output capacitor
- Internal current limit and thermal protection
- Fixed output versions from 1.2 V to 12 V on request, and adjustable version
Applications:
- Battery-powered equipment
- TV
- Set-top box
- PC and laptop
- Industrial
Package:
- SOT23-5L (LDK220M-R, 5 pins)
- Other LDK220 family packages: SOT323-5L, SOT-89, DFN6 1.2x1.3
LDK220 Features
- Input voltage from 2.5 to 13.2 V
- Very low-dropout voltage (100 mV typ. @ 100 mA load)
- Low quiescent current (typ. 55 μA, 1 μA in off mode)
- Low noise
- Output voltage tolerance: ± 2.0% @ 25 °C
- 200 mA guaranteed output current
- Wide range of output voltages available on request: fixed from 1.2 V to 12 V with 100 mV step and adjustable
- Logic-controlled electronic shutdown
- Output discharge function
- Compatible with ceramic capacitor C OUT = 1 μF
- Internal current and thermal limit
- Available in SOT23-5L, SOT323-5L, SOT-89 and DFN6-1.2x1.3 packages
- Temperature range: -40 °C to 125 °C
LDK220 Applications
- Battery-powered equipment
- TV
- Set-top box
- PC and laptop
- Industrial
LDK220 Electrical Characteristics
Table 6. LDK220 electrical characteristics for fixed output version. T J = 25 °C, V IN = V OUT(NOM) + 1 V, C IN = COUT = 1 μF, I OUT = 1 mA, V EN = V IN , unless otherwise specified.
| Symbol | Parameter | Test conditions | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|---|
| V IN | Operating input voltage | 2.5 | 13.2 | V | ||
| V OUT | V OUT accuracy | I OUT = 1 mA, T J = 25 °C | -2 | 2 | % | |
| V OUT | V OUT accuracy | I OUT = 1 mA, -40 °C < T J < 125 °C | -3 | 3 | % | |
| ΔV OUT | Static line regulation | V OUT + 1 V ≤ V IN ≤ 13.2 V, I OUT = 1 mA | 0.001 | 0.05 | %/V | |
| ΔV OUT | Static load regulation | I OUT = 1 mA to 200 mA I OUT = 100 mA, V OUT = 3.3 V | 0.001 100 | 0.003 | %/mA | |
| V DROP | Dropout voltage (1) | I OUT = 200 mA, V OUT = 3.3 V 40 °C < T J < 125 °C | 200 | 350 | mV | |
| e N | Output noise voltage | 10 Hz to 100 kHz, I OUT = 10 mA | 20 | μV RMS /V | ||
| SVR | Supply voltage rejection | V IN = V OUTNOM + 0.5 V+/-V RIPPLE V RIPPLE = 0.1 V frequency = 120 Hz to 1 kHz I OUT = 10 mA | 55 | dB | ||
| SVR | Supply voltage rejection | V IN = V OUTNOM + 0.5 V+/-V RIPPLE I OUT = 10 mA V RIPPLE = 0.1 V frequency = 10 kHz | 50 | dB | ||
| I Q | Quiescent current | V IN = V OUT +1 V I OUT = 0 mA,-40 °C < T J < 125 °C | 55 | 90 | μA | |
| I Q | Quiescent current | V OUT +1 V ≤ V IN ≤ 13.2 V (2) I OUT = 200 mA,-40 °C < T J < 125 °C | 60 | 100 | μA | |
| I Q | Quiescent current | V IN input current in off mode: V EN = GND, T J = 25 °C | 0.1 | 1 | μA | |
| I SC | Short-circuit current (2) | R L = 0 | 400 | mA | ||
| V EN | Enable input logic low Enable input logic high | V IN = 2.5 V to 13.2 V, -40 °C < T J < 125 °C V = 2.5 V to 13.2 V, -40 °C < T < 125 °C | 1.2 | 0.4 | V | |
| I EN | Enable pin input current | V EN = V IN | 0.1 | 100 | nA | |
| Rdis | Discharger resistor | V EN = 0 | 18 | Ω | ||
| T SHDN | Thermal shutdown Hysteresis | 160 20 | °C | |||
| C OUT | Output capacitor | Capacitance (see Section 6 Typical characteristics) | 1 | 22 | μF |
Table 7. LDK220 electrical characteristics for adjustable version. T J = 25 °C, V IN = V OUT(NOM) + 1 V, C IN = COUT = 1 μF, I OUT = 1 mA, V EN = V IN , unless otherwise specified.
| Symbol | Parameter | Test conditions | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|---|
| V IN | Operating input voltage | 2.5 | 13.2 | V | ||
| Adjustable voltage | T J = 25 °C | 1.185 | V | |||
| V ADJ | Adjustable voltage | T J = 25 °C | -2 | +2 | ||
| accuracy | 40 °C < T J < 125 °C | -3 | +3 | % | ||
| ΔV OUT | Static line regulation | V OUT +1 V ≤ V IN ≤ 13.2 V I OUT =1 mA | 0.001 | 0.05 | %/V | |
| ΔV OUT | Static load regulation | I OUT = 1 mA to 200 mA | 0.0002 | 0.003 | %/mA | |
| V | I OUT = 100 mA, V OUT = 3.3 V | 100 | ||||
| DROP | Dropout voltage (1) | I OUT = 200 mA, V OUT = 3.3 V 40 °C < T J < 125 °C | 200 | 350 | mV | |
| e N | Output noise voltage | 10 Hz to 100 kHz, I OUT = 10 mA | 100 | μV RMS /V | ||
| I ADJ | Adjust pin current | 1 | μA | |||
| SVR | Supply voltage rejection | V IN = V OUTNOM + 0.5 V+/-V RIPPLE V RIPPLE = 0.1 V frequency = 120 Hz to1 kHz, I OUT = 10 mA | 60 | dB | ||
| Supply voltage rejection | V RIPPLE = 0.1 V V IN = V OUTNOM +0.5 V+/- V RIPPLE frequency = 10 kHz, I OUT = 10 mA V OUT +1 V ≤ V IN ≤ 13.2 V I OUT = 0 mA, -40 °C < T J < 125 °C | 45 55 | 90 | dB | ||
| I Q | Quiescent current | V OUT +1 V ≤ V IN ≤ 13.2 V I OUT = 200 mA,-40 °C < T J < 125 °C (2) | 60 | 100 | μA | |
| Quiescent current | V IN input current in off mode: V EN = GND,T J = 25 °C | 0.1 | 1 | |||
| I SC | Short-circuit current (2) | R L = 0 | 400 | mA | ||
| V EN | Enable input logic low Enable input logic high | V IN = 2.5 V to 13.2 V -40 °C < T J < 125 °C V IN = 2.5 V to 13.2 V -40 °C < T J < 125 °C | 1.2 | 0.4 | V | |
| I EN | Enable pin input current | V EN = V IN | 0.1 | 100 | nA | |
| T | Thermal shutdown | 160 | °C | |||
| SHDN | Hysteresis | 20 | °C | |||
| C OUT | Output capacitor | Capacitance (see Section 6 Typical characteristics) | 1 | 22 | μF |
LDK220 Absolute Maximum Ratings
Table 4. Absolute maximum ratings
| Symbol | Parameter | Value | Unit |
|---|---|---|---|
| V IN | DC input voltage | - 0.3 to 14 | V |
| V OUT | DC output voltage | - 0.3 to VI + 0.3 | V |
| V EN | Enable input voltage | - 0.3 to VI + 0.3 | V |
| V ADJ | ADJ pin voltage | - 0.3 to 2 | V |
| I OUT | Output current | Internally limited | mA |
| P D (1) | Power dissipation | 500 | mW |
| T STG | Storage temperature range | - 65 to 150 | °C |
| T OP | Operating junction temperature range | - 40 to 125 | °C |
Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All values are referred to GND.
Table 5. Thermal data
| Symbol | Parameter | SOT23-5L | SOT323-5L | SOT-89 | DFN-6 | Unit |
|---|---|---|---|---|---|---|
| R thJA | Thermal resistance junction- ambient | 160 | 246 | 110 | 237 | °C/W |
| R thJC | Thermal resistance junction-case | 68 | 134 | 15 | 104 | °C/W |
Note:
JESD 51, 4 LAYERS 2S2P.
LDK220 Typical Application
Figure 4. Typical application circuits
Note: Adjustable version and enable pin are not available on the SOT-89 package.
LDK220 Package Information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.
7.1
Variants on the same datasheet
These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.
| Part Number | Manufacturer | Package |
|---|---|---|
| LDK220M-R | STMicroelectronics | SC-74A, SOT-753 |
More datasheets
Ask your AI agent about the LDK220
Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.
claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp
Then ask: "Can the LDK220 run from my 12 V rail? Check it against the datasheet limits."
Create a free account $2 of usage every month, no card needed.