LCZ260

Hall-effect Zero Speed Sensor

The LCZ260 is a hall-effect zero speed sensor from Honeywell. View the full LCZ260 datasheet below including key specifications, pinout.

Official LCZ260 datasheet (PDF) — the source this page was extracted from.

Manufacturer

Honeywell

LCZ260 Key Specifications

Parameter	Value
Actuator Material	Ferrous Metals, Gear Tooth
Frequency	15 kHz
Operating Temperature	-40°C ~ 125°C
Output Type	Digital
Package / Case	Barrel, Stainless Steel
Standard Pack Qty	1
Termination Style	Wire Leads
Type	Hall Effect Sensor
Supply Voltage	4.5V ~ 26V

LCZ260 Overview

Part: LCZ260 Series Type: Hall-effect Zero Speed Sensor

Description: A durable, cost-effective single Hall-effect zero speed sensor with a digital output, operating from 4.5 Vdc to 26 Vdc and capable of detecting frequencies from 0 Hz to 15 kHz.

Operating Conditions:

Supply voltage: 4.5 Vdc to 26 Vdc
Operating temperature: -40 °C to 125 °C
Operating frequency: 0 Hz to 15 kHz

Absolute Maximum Ratings:

Max supply voltage: 26 Vdc
Max continuous current: 20 mA (supply current), 20 mA (output sinking)
Max storage temperature: 125 °C

Key Specs:

Supply current: Max 20 mA (load = infinity, Vcc = 26)
Output sinking current: Max 20 mA (0.4 V max. short circuit protected)
Voltage low: Max 0.4 V (at 30 mA max. sink)
Output signal rise/fall time: Max 4.0 μs (880 Ohm, 20 pF)
Output impedance: 4.7 kOhm to 5.3 kOhm
Dielectric strength: 200 Vac (<2 mA leakage)
Sealing: IP68
Shock: 50 Gs, 11 ms

Features:

Low cost
Omni-directional sensor to target orientation
Digital output
Small size
Low power consumption

Applications:

Industrial process control
Factory automation
Rotary applications, such as pumps, rollers, mixers, fan speed measurement, transmission, spindles, gear reducer RPM and process speed
Synchronization
Generator set
Compressor speed
Dyno testing

Package:

9,5 mm [3/8 in] diameter, 50,8 mm [2.00 in] length (3/8-24UNF-2A thread)
9,5 mm [3/8 in] diameter, 76,2 mm [3.00 in] length (3/8-24UNF-2A thread)
15,9 mm [5/8 in] diameter, 50,8 mm [2.00 in] length (5/8-18UNF-2A thread)
15,9 mm [5/8 in] diameter, 76,2 mm [3.00 in] length (5/8-18UNF-2A thread)

LCZ260 Features

Low cost
Omni-directional sensor to target orientation
Digital output
Small size
Low power consumption

LCZ260 Applications

Industrial process control
Factory automation
Rotary applications, such as pumps,
rollers, mixers, fan speed measurement, transmission, spindles, gear reducer RPM and process speed

LCZ260 Pin Configuration

LCZ260 – Barrel Sensor with Three-Conductor Cable

Wire Color	Pin Name	Type	Description
Red	Power Supply (+)	Power Input	Supply voltage: 4.5–26 Vdc
White	Signal Output	Output	Digital output signal (open-drain, 20 mA max sink)
Black	Common	Ground	Ground/return (negative supply)
Shield	Shield (NC)	Shield	Shielding; not connected internally

Notes

Package: Barrel, stainless steel, 3/8-24UNF-2A thread, 50.8 mm [2.00 in] length
Cable: 1750 mm [69 in] three-conductor 24 AWG cable with shield
Output: Open-drain digital output with 4.7–5.3 kΩ internal pull-up resistor; maximum sink current 20 mA at 0.4 V
Operating conditions: 0–15 kHz frequency range, −40 to +125 °C temperature range, IP68 sealing
No pin numbers: This is a sensor with loose wire leads, not a packaged IC. Connections are identified by wire color per the electrical schematic.

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part Number	Manufacturer	Package
LCZ260-30	Honeywell Sensing and Productivity Solutions	Cylinder, Threaded
LCZ460	Honeywell	—
LCZ460-30	Honeywell	—

More datasheets

All Honeywell datasheets (7)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the LCZ260

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the LCZ260 run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.