FE1.1S-BSOP28BPTR

Part: FE1.1s Revision B — Terminus

Type: USB 2.0 High Speed 4-Port Hub Controller

Description: A highly integrated USB 2.0 High Speed 4-port hub controller fully compliant with USB 2.0 and Battery Charging Specification 1.1/1.2, supporting Universal Charging Solution (UCS) with integrated transceivers, regulators, and power-on-reset.

Operating Conditions:

• Supply voltage: 4.5–5.5 V (VDD5), 3.0–3.6 V (VD33)
• Operating temperature: 0 to 70 °C
• Digital input high level voltage: 2.0–5.5 V

Absolute Maximum Ratings:

• Max junction/storage temperature: +150 °C

Key Specs:

• Upstream Port Speed: High-Speed (480MHz), Full-Speed (12MHz)
• Downstream Port Speed: High-Speed, Full-Speed, Low-Speed (12MHz)
• XIN input capacitance: 32 ρF (Typ.)
• Internal Pull-Up Resistor Range: 39–116 KΩ
• Digital input low level voltage: -0.3–0.8 V
• Digital output high level voltage: 2.4 V (Min.)
• Digital output low level voltage: 0.4 V (Max.)
• Crystal Frequency Accuracy: 12MHz ± 50ppm
• Crystal Load Capacitance: 16pF ~ 20pF

Features:

• Fully compliant with USB 2.0 and USB Battery Charging Specification 1.1/1.2
• Integrated USB 2.0 Transceivers
• Integrated 5V to 3.3V and 1.8V regulators
• Integrated Power-On-Reset with power failure detection circuit
• Integrated 12MHz Oscillator and 12MHz-to-480MHz Phase Lock Loop (PLL)
• Single Transaction Translator (Single TT) for all downstream ports
• Ganged Power Control and Global OverCurrent Detection support
• EEPROM configurable options (Vendor ID, Product ID, Device Release Number, Number of Downstream Ports)
• Board configurable Port Indicators (Individual, Joint, or Charging Request/Portable Device Detection)

Applications:

• Embedded applications
• Standalone hubs
• USB Charging Hubs for Universal Charging Solution compliant devices

Package:

• 24-pin WQFN (4mm x 4mm)
• 28-pin SSOP (10mm x 4mm)
• 48-pin LQFP (7mm x 7mm)

• Fully compliant with Universal Serial Bus Specification Revision 2.0 (USB 2.0);

• □ Upstream Facing Port supports HighSpeed (480MHz) and Full-Speed (12MHz) modes;

• □ 4 Downstream Facing Ports support HighSpeed, Full-Speed, and Low-Speed (12MHz) modes;

• Compliant with Universal Charging Solution, and USB Battery Charging Specification 1.1/1.2.

• Integrated USB 2.0 Transceivers;

• Integrated upstream 1.5KΩ pull-up, downstream 15KΩ pull-down, and serial resistors;

• Integrated 5V to 3.3V and 1.8V regulators;

• Integrated Power-On-Reset with power failure detection circuit;

• Integrated 12MHz Oscillator with feedback resistor and crystal load capacitors;

• Integrated 12MHz-to-480MHz Phase Lock Loop (PLL);

• Integrated Portable Device detection circuitry for UCS supporting;

• Single Transaction Translator (Single TT) -

• □ One TT for all downstream ports;

• □ The TT could handle 64 periodic StartSplit transactions, 32 periodic CompleteSplit transactions, and 6 none-periodic transactions;

• Ganged Power Control and Global OverCurrent Detection support;

• EEPROM configured options -

• □ Vendor ID, Product ID, & Device Release Number; and

• □ Number of Downstream Ports;

• Automatic re-enumeration when hub switches from self-powered mode to bus-powered mode;

• Board configured comprehensive Port Indicators support:

• □ Four Downstream Port Enabled indicator LED (Green, one for each port), plus one Active/Suspend indicator LED (Red); or

• □ One joint Downstream Port Enabled indicator LED (Green, one for all ports), plus one Active/Suspend indicator LED (Red); or

• □ One joint Downstream Port Enabled indicator LED (Green, one for all ports), plus one Charging Request/Portable Device Detection indicator LED (Blue);

• Board configure support of portable device detection mechanism for Universal Charging Solution on all 4 downstream ports.

FE1.1S-BSOP28BPTR Pinout

Package: SSOP-28-150mil

Notes

• Pin numbers and names extracted directly from the SSOP-28 pin diagram (Fig. 2).
• NC pins (12, 13, 28) are No Connect; pin 28 is also labeled NC in the diagram.
• Power pins: VSS (1), VDD5 (20), VD33F (21).
• USB data lines organized by port: DP1–DM1 (Port 1), DP2–DM2 (Port 2), DP3–DM3 (Port 3), DP4–DM4 (Port 4), DPU–DMU (Upstream).
• Crystal interface: XIN (3), XOUT (2), XRSTJ (17).