Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

ET95101

Li-Ion Linear Battery Charger

The ET95101 is a li-ion linear battery charger from ETEK MICROELECTRONICS. View the full ET95101 datasheet below including key specifications.

Official ET95101 datasheet (PDF) — the source this page was extracted from.

Manufacturer

ETEK MICROELECTRONICS

Category

Li-Ion Linear Battery Charger

Package

-

Lifecycle

Active

ET95101 Key Specifications

ParameterValue
Battery ChemistryLithium Ion
Battery Pack Voltage4.2V
Charge Current (Max)250mA
Current - ChargingConstant
Mounting TypeSurface Mount
Number of Cells1
Operating Temperature-40°C ~ 85°C (TA)
Supplier Device Package6-WLCSP (1.36x0.76)
Input Voltage (Max)28V

ET95101 Overview

Part: ET95101

Type: Single-Cell Li-Ion Linear Battery Charger

Description: 30 V-rated input (6.5 V OVP), 10–250 mA programmable linear Li-Ion charger with 1% voltage accuracy, JEITA temperature-aware charging and a fixed 10-hour safety timer, in a 1.30 × 0.9 mm CSP6 package.

Operating Conditions:

  • Supply voltage (VIN): 3.5–28 V; IN operating voltage range 4.45–6.45 V
  • Junction temperature range: 0 to 125 °C
  • Fast-charge current: 10–250 mA (RISET 0.54–13.5 kΩ)

Absolute Maximum Ratings:

  • Max supply input voltage (VIN): 30 V
  • Other pins: 6 V
  • Input current: 300 mA
  • Output current: 300 mA
  • Output sink current: 15 mA
  • Junction temperature: -40 to 150 °C

Key Specs:

  • Output regulation voltage VOUT(REG): 4.16 / 4.2 / 4.24 V (min/typ/max; VIN = 5 V, RISET = 1.35 kΩ)
  • Hot regulation voltage: 4.0 / 4.06 / 4.12 V (battery 45–60 °C)
  • UVLO exit threshold: 3.15 / 3.3 / 3.45 V
  • Input OVP threshold: 6.50 / 6.65 / 6.8 V
  • VIN-DPM threshold: 4.15 / 4.30 / 4.45 V
  • Battery leakage into OUT (VIN = 0 V, VOUT = 4 V): 75 nA max (100 nA max at 0–85 °C)
  • Standby current into IN (TS = GND): 110 μA typ, 145 μA max
  • Dropout (VIN − VOUT) at IOUT = 0.2 A: 400 mV max
  • OUT current clamp: 550 / 650 / 750 mA

Features:

  • 1% charging voltage accuracy and 10% charging current accuracy
  • Supports ultra-low charge current (10–250 mA) and termination current down to 1 mA
  • Input over-voltage protection and input dynamic power management (IN-DPM)
  • Thermal regulation at 120 °C and thermal shutdown at 150 °C
  • OUT short-circuit protection and ISET short-circuit detection
  • JEITA-compliant NTC monitoring (current halved when cold, 4.06 V when hot)
  • Fixed 10-hour safety timer and 30-minute pre-charge timer
  • Termination and timer disable mode (TTDM) for missing battery pack
  • Open-drain CHG status output

Applications:

  • Fitness accessories
  • Smart watches
  • Bluetooth headphones
  • Low-power handheld devices

Package:

  • CSP6 (1.30 mm × 0.9 mm), MSL Level 1
Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the ET95101

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the ET95101 run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.