Skip to main content

We use cookies to understand how you use our site and improve your experience. See our Privacy Policy.

BQ27220YZFR.A

Single-Cell Battery Fuel Gauge

The BQ27220YZFR.A is a single-cell battery fuel gauge from Texas Instruments. View the full BQ27220YZFR.A datasheet below including key specifications, electrical characteristics, absolute maximum ratings.

BQ27220YZFR.A shares its datasheet with BQ27220, whose page lists every part number it covers.

Official BQ27220YZFR.A datasheet (PDF) — the source this page was extracted from.

Manufacturer

Texas Instruments

Category

Single-Cell Battery Fuel Gauge

BQ27220YZFR.A Key Specifications

ParameterValue
NORMAL mode current50 μA typ (TA = 30 °C, VBAT = 3.6 V)
SLEEP mode current9 μA typ
SHUTDOWN mode current0.6 μA typ
LDO output voltage (VDD)1.85 V typ
UVLO2 V rising / 1.95 V falling (typ)
Cell voltage ADC15-bit effective resolution, 125 ms conversion time
Coulomb counter16-bit effective resolution, ±80 mV differential input range, 1 s single conversion
Power-up communication delay250 ms typ
Thermal resistance RθJA64.1 °C/W (YZF)
ESD±1500 V HBM, ±250 V CDM

BQ27220YZFR.A Overview

Part: bq27220 — Texas Instruments

Type: Single-Cell Li-Ion Battery Fuel Gauge (CEDV)

Description: Single-cell CEDV fuel gauge with integrated LDO, 2.45–4.5 V battery input range, 10 mΩ external sense resistor support, 50 μA NORMAL and 9 μA SLEEP current, and 400 kHz I²C interface in a 9-ball DSBGA package.

Operating Conditions:

  • Supply voltage (VBAT, BAT pin regulator input): 2.45–4.5 V
  • Operating temperature: -40 to 85 °C
  • I²C clock: up to 400 kHz (Fast Mode)
  • Open-drain pullup voltage (SDA, SCL, GPOUT): 1.62–3.6 V

Absolute Maximum Ratings:

  • BAT pin input voltage: -0.3 to 6 V
  • SRP/SRN input voltage: -0.3 to VBAT + 0.3 V
  • Differential voltage across SRP and SRN: 2 V
  • VDD pin voltage: -0.3 to 2 V
  • Open-drain IO pins (SDA, SCL): -0.3 to 6 V
  • Storage temperature: -65 to 150 °C

Key Specs:

  • NORMAL mode current: 50 μA typ (TA = 30 °C, VBAT = 3.6 V)
  • SLEEP mode current: 9 μA typ
  • SHUTDOWN mode current: 0.6 μA typ
  • LDO output voltage (VDD): 1.85 V typ
  • UVLO: 2 V rising / 1.95 V falling (typ)
  • Cell voltage ADC: 15-bit effective resolution, 125 ms conversion time
  • Coulomb counter: 16-bit effective resolution, ±80 mV differential input range, 1 s single conversion
  • Power-up communication delay: 250 ms typ
  • Thermal resistance RθJA: 64.1 °C/W (YZF)
  • ESD: ±1500 V HBM, ±250 V CDM

Features:

  • Resides in pack or on system board; supports embedded or removable batteries
  • Powers directly from battery via integrated LDO
  • Supports a low-value 10 mΩ external sense resistor (pre-calibrated)
  • CEDV fuel gauging with remaining capacity and SOC reporting with smoothing filter
  • Automatic adjustment for battery aging, self-discharge, temperature and rate changes
  • State-of-health (aging) estimation
  • Configurable SOC interrupt or battery-low digital output (GPOUT)
  • Internal temperature sensor, host-reported temperature, or external thermistor
  • Preloaded CEDV parameters in ROM, or custom parameters via GAUGEPARCAL (RAM or OTP)

Applications:

  • Smartphones and feature phones
  • Tablets
  • Wearables
  • Building automation
  • Portable medical/industrial handsets
  • Portable audio
  • Gaming

Package:

  • YZF (DSBGA, 9 balls), 1.62 mm × 1.58 mm, 0.5 mm pitch

BQ27220YZFR.A Features

  • 1 · Single-Cell Li-Ion Battery Fuel Gauge
  • -Resides in Pack or on System Board
  • -Supports Embedded or Removable Batteries
  • -Powers Directly from Battery with Integrated LDO
  • -Supports a Low-Value (10-m Ω ) External Sense Resistor
  • Ultra-Low Power Consumption in NORMAL (50 μA) and SLEEP (9 μA) Modes
  • Battery Fuel Gauging Based on Compensated End-of-Discharge Voltage (CEDV) Technology
  • -Reports Remaining Capacity and State-ofCharge (SOC) with Smoothing Filter
  • -Adjusts Automatically for Battery Aging, SelfDischarge, Temperature, and Rate Changes
  • -Provides Battery State-of-Health (Aging) Estimation
  • Microcontroller Peripheral Supports:
  • -400-kHz I 2 C™ Serial Interface
  • -Configurable SOC Interrupt OR Battery Low Digital Output Warning
  • -Internal Temperature Sensor OR Host-Reported Temperature OR External Thermistor

BQ27220YZFR.A Applications

  • Smartphones and Feature Phones
  • Tablets
  • Wearables
  • Building Automation
  • Portable Medical/Industrial Handsets
  • Portable Audio
  • Gaming

1

BQ27220YZFR.A Pin Configuration

PIN - NAMEPIN - NUMBERTYPEDESCRIPTION
BATC3PI, AI (1)LDO regulator input and battery voltage measurement input. Kelvin sense connect to the positive battery terminal (PACKP). Connect a capacitor (1 μF) between BAT and V SS . Place the capacitor close to the gauge.
BINB1DIBattery insertion detection input. If OpConfig [BI_PU_EN] = 1 (default), a logic low on the pin is detected as battery insertion. For a removable pack, the BIN pin can be connected to V SS through a pulldown resistor on the pack, typically the 10-k Ω thermistor; the system board should use a 1.8-M Ω pullup resistor to V DD to ensure the BIN pin is high when a battery is removed. If the battery is embedded in the system or in the pack, it is recommended to leave [BI_PU_EN] = 1 and use a 10-k Ω pulldown resistor from BIN to V SS . If [BI_PU_EN] = 0, then the host must inform the gauge of battery insertion and removal with the BAT_INSERT and BAT_REMOVE subcommands. A 10-k Ω pulldown resistor should be placed between BIN and V SS , even if this pin is unused. NOTE: The BIN pin must not be shorted directly to V CC or V SS and any pullup resistor on the BIN pin must be connected only to V DD and not an external voltage rail. If an external thermistor is used for temperature input, the thermistor should be connected between this pin and V SS .

BQ27220YZFR.A Electrical Characteristics

TA = -40°C to 85°C, typical values at TA = 30°C and VBAT = 3.6 V (unless otherwise noted)(Force Note1)

(1)

PARAMETERPARAMETERTEST CONDITIONSMINTYPMAXUNIT
V IH(OD)Input voltage, high (2)External pullup resistor to V PUV PU × 0.7V
V IH(PP)Input voltage, high (3)1.4V
V ILInput voltage, low (2) (3)0.6V
V OLOutput voltage, low (2)0.6V
I OHOutput source current, high (2)0.5mA
I OL(OD)Output sink current, low (2)-3mA
C IN (1)Input capacitance (2)(3)5pF
I lkgInput leakage current (SCL, SDA, BIN, GPOUT)1μ A

BQ27220YZFR.A Absolute Maximum Ratings

Over operating free-air temperature range (unless otherwise noted) (1)

MINMAXUNIT
V BATBAT pin input voltage range-0.36V
V SRSRP and SRN pins input voltage range-0.3V BAT + 0.3V
V SRDifferential voltage across SRP and SRN. ABS(SRP - SRN)2V
V DDV DD pin supply voltage range (LDO output)-0.32V
V IODOpen-drain IO pins (SDA, SCL)-0.36V
V IOPPPush-pull IO pins (BIN)-0.3V DD + 0.3V
T AOperating free-air temperature range-4085°C
Storage temperature, T stgStorage temperature, T stg-65150°C

TA = 30°C and VBAT = 3.6 V (unless otherwise noted)

MINNOMMAXUNIT
C BAT (1)External input capacitor for internal LDO between BAT and V SSNominal capacitor values specified. Recommend a 5% ceramic X5R-type capacitor located close to the device.0.1μ F
C LDO18 (1)External output capacitor for internal LDO between V DD and V SSNominal capacitor values specified. Recommend a 5% ceramic X5R-type capacitor located close to the device.2.2μ F
V PU (1)External pullup voltage for open-drain pins (SDA, SCL, GPOUT)1.623.6V

BQ27220YZFR.A Thermal Information

THERMAL METRIC (1)bq27220 YZF (DSBGA) - 9 PINSUNIT
R θ JAJunction-to-ambient thermal resistance64.1°C/W
R θ JCtopJunction-to-case (top) thermal resistance59.8°C/W
R θ JBJunction-to-board thermal resistance52.7°C/W
ψ JTJunction-to-top characterization parameter0.3°C/W
ψ JBJunction-to-board characterization parameter28.3°C/W
R θ JCbotJunction-to-case (bottom) thermal resistance2.4°C/W

BQ27220YZFR.A Typical Application

The bq27220 fuel gauge is a microcontroller peripheral that provides system-side or pack-side fuel gauging for single-cell Li-Ion batteries. The device requires minimal configuration and uses One-Time Programmable (OTP) Non-Volatile Memory (NVM). Battery fuel gauging with the fuel gauge requires connections only to PACK+ and PACK- for a removable battery pack or embedded battery circuit. To allow for optimal performance in the end application, special considerations must be taken to ensure minimization of measurement error through proper printed circuit board (PCB) board layout. Such requirements are detailed in Design Requirements .

Variants on the same datasheet

These parts have exact links to the same datasheet. They are candidates to compare, not verified drop-in replacements; check package, pinout and electrical limits.

Part NumberManufacturerPackage
BQ27220Texas InstrumentsDSBGA-9
BQ27220YZFRTexas Instruments
BQ27220YZFTTexas Instruments—
BQ27220YZFT.ATexas Instruments—

More datasheets

All Texas Instruments datasheets (2,670)

Data on this page is extracted from publicly available manufacturer datasheets using automated tools including AI. It may contain errors or omissions. Always verify specifications against the official manufacturer datasheet before making design or purchasing decisions. See our Terms of Service. Rights holders can submit a takedown request.

Ask your AI agent about the BQ27220YZFR.A

Connect SheetsData to Claude, Cursor, Codex or any MCP client and your agent reads this datasheet for you: pinout, limits, register maps and design checks, with the numbers taken from the PDF.

claude mcp add --transport http sheetsdata https://mcp.sheetsdata.com/mcp

Then ask: "Can the BQ27220YZFR.A run from my 12 V rail? Check it against the datasheet limits."

Create a free account $2 of usage every month, no card needed.